EN 13963:2005

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Jointing materials for gypsum plasterboards - Definitions, requirements and test methodsMatériaux de jointoiement pour plaques de plâtre - Définitions, exigences et méthodes d'essaiMaterialien für das Verspachteln von Gipsplatten-Fugen - Begriffe, Anforderungen und Prüfverfahren91.100.10Cement. Mavec. Apno. MaltaCement. Gypsum. Lime. MortarICS:SIST EN 13963:2005enTa slovenski standard je istoveten z:EN 13963:200501-september-2005SIST EN 13963:2005SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13963May 2005ICS 91.100.10English versionJointing materials for gypsum plasterboards - Definitions,requirements and test methodsMatériaux de jointoiement pour plaques de plâtre -Définitions, exigences et méthodes d'essaiMaterialien für das Verspachteln von Gipsplatten-Fugen -Begriffe, Anforderungen und PrüfverfahrenThis European Standard was approved by CEN on 14 February 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2005 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13963:2005: E

Sampling procedure for testing.23 Annex B (informative)
Guidance on the use of jointing materials.24 Annex C (normative)
Mounting and fixing in the test according to EN 13823 (SBI test).25 Annex ZA (informative)
Clauses of this European Standard addressing provisions of EU Construction Products Directive.26 Bibliography.31

Diagram 1 – General diagram showing families of gypsum products

Diagram 2 – Families of ancillary products The jointing compounds specified in this document are used to fill and finish the joints formed at the edges and ends of gypsum plasterboard complying with EN 520, products from secondary processing of this board and gypsum boards with fibrous reinforcement.

(powder or ready-mix) Setting
(powder only) Bedding compound 1A 1B Finishing compound 2A 2B Dual-purpose compound 3A 3B Tapeless jointing compound 4A 4B NOTE See Annex B for guidance for use. 4 Requirements 4.1 Reaction to fire Jointing materials for gypsum plasterboards are classified in Euroclass A1 (no contribution to fire) without testing when they contain less than 1 % by weight or by volume (whichever is the more onerous) of organic materials1). If the products contain 1 % or more by weight or by volume (whichever is the more onerous) of organic material, they shall be tested and then classified in accordance with EN 13501-1. Jointing materials tested according to EN 13823 (SBI test) shall be mounted and fixed in accordance with Annex C or, when the producer wishes to claim performance for a specific intended use, the mounting and fixing shall be representative of that intended use. 4.2 Flexural strength (expressed as breaking load) Breaking load shall be measured according to test method 5.8.2 for types 1, 2 and 3 and according to test method 5.8.1 for types 4A and 4B (tapeless jointing compound). 4.3 Regulated substances Materials used in products shall not release any regulated substances in excess of the maximum permitted levels specified in a relevant European Standard for the material or permitted in the national regulations of the member state of destination. 4.4 Setting time When compound types 1B, 2B, 3B and 4B are tested by the method given in 5.2, the setting time shall be not less than 20 min but less than 60 min for a short setting compound.
It shall not be less than 60 min b
...