EN ISO 11755:2020

SLOVENSKI STANDARD
01-december-2020
Plinske jeklenke - Snopi jeklenk za stisnjene in utekočinjene pline (razen acetilena)
- Kontrola polnjenja (ISO 11755:2005)
Gas cylinders - Cylinder bundles for compressed and liquefied gases (excluding
acetylene) - Inspection at time of filling (ISO 11755:2005)
Gasflaschen - Flaschenbündel für verdichtete und verflüssigte Gase (ausgenommen
Acetylen) - Prüfung zum Zeitpunkt des Füllens (ISO 11755:2005)
Bouteilles à gaz - Cadres de bouteilles pour gaz comprimés et liquéfiés (à l'exclusion de
l'acétylène) - Inspection au moment du remplissage (ISO 11755:2005)
Ta slovenski standard je istoveten z: EN ISO 11755:2020
ICS:
23.020.35 Plinske jeklenke Gas cylinders
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 11755
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2020
EUROPÄISCHE NORM
ICS 23.020.35
English Version
Gas cylinders - Cylinder bundles for compressed and
liquefied gases (excluding acetylene) - Inspection at time
of filling (ISO 11755:2005)
Bouteilles à gaz - Cadres de bouteilles pour gaz Gasflaschen - Flaschenbündel für verdichtete und
comprimés et liquéfiés (à l'exclusion de l'acétylène) - verflüssigte Gase (ausgenommen Acetylen) - Prüfung
Inspection au moment du remplissage (ISO zum Zeitpunkt des Füllens (ISO 11755:2005)
11755:2005)
This European Standard was approved by CEN on 28 September 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11755:2020 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
The text of ISO 11755:2005 has been prepared by Technical Committee ISO/TC 58 "Gas cylinders” of
the International Organization for Standardization (ISO) and has been taken over as EN ISO 11755:2020
by Technical Committee CEN/TC 23 “Transportable gas cylinders” the secretariat of which is held by
BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2021, and conflicting national standards shall be
withdrawn at the latest by April 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 11755:2005 has been approved by CEN as EN ISO 11755:2020 without any modification.

INTERNATIONAL ISO
STANDARD 11755
Second edition
2005-06-01
Gas cylinders — Cylinder bundles for
compressed and liquefied gases
(excluding acetylene) — Inspection at
time of filling
Bouteilles à gaz — Cadres de bouteilles pour gaz comprimés et liquéfiés
(à l'exclusion de l'acétylène) — Inspection au moment du remplissage

Reference number
ISO 11755:2005(E)
©
ISO 2005
ISO 11755:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
©
ii ISO 2005 – All rights reserved

ISO 11755:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11755 was prepared by Technical Committee ISO/TC 58, Gas cylinders, Subcommittee SC 4, Operational
requirements for gas cylinders.
This second edition cancels and replaces the first edition (ISO 11755:1996), which has been technically
revised.
©
ISO 2005 – All rights reserved iii

ISO 11755:2005(E)
Introduction
Transportable gas cylinder bundles require inspection before, during and after the filling process to ensure that
all components are suitable for the intended filling conditions, and are free of serious defects and contamination
that can affect the integrity of the bundle.
©
iv ISO 2005 – All rights reserved

INTERNATIONAL STANDARD ISO 11755:2005(E)
Gas cylinders — Cylinder bundles for compressed and liquefied
gases (excluding acetylene) — Inspection at time of filling
1Scope
This International Standard specifies the requirements for inspection before, during and after the time of filling
for cylinder bundles for compressed and liquefied gases, also referred to as bu
...