EN 4122:2004

SLOVENSKI STANDARD
01-junij-2005
1DGRPHãþD
SIST EN 4122:2004
Aerospace series - Shank nuts, self-locking, in heat resisting steel FE-PA2601
(A286), silver plated on thread - Classification: 1 100 MPa (at ambient
temperature) / 650 °C
Aerospace series - Shank nuts, self-locking, in heat resisting steel FE-PA2601 (A286),
silver plated on thread - Classification: 1 100 MPa (at ambient temperature) / 650 °C
Luft- und Raumfahrt - Einnietmuttern, selbstsichernd, aus hochwarmfestem Stahl FE-
PA2601 (A286), Gewinde versilbert - Klasse: 1 100 MPa (bei Raumtemperatur) / 650 °C
Série aérospatiale - Écrous a sertir, a freinage interne, en acier résistant a chaud FE-
PA2601 (A286), argentés sur filetage - Classification : 1 100 MPa (a température
ambiante ) / 650 °C
Ta slovenski standard je istoveten z: EN 4122:2004
ICS:
49.030.30 Matice Nuts
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 4122
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2004
ICS 49.030.30 Supersedes EN 4122:2003
English version
Aerospace series - Shank nuts, self-locking, in heat resisting
steel FE-PA2601 (A286), silver plated on thread - Classification:
1 100 MPa (at ambient temperature) / 650° C
Série aérospatiale - Écrous à sertir, à freinage interne, en Luft- und Raumfahrt - Einnietmuttern, selbstsichernd, aus
acier résistant à chaud FE-PA2601 (A286), argentés sur hochwarmfestem Stahl FE-PA2601 (A286), Gewinde
filetage - Classification : 1 100 MPa (à température versilbert - Klasse: 1 100 MPa (bei Raumtemperatur) / 650°
ambiante ) / 650° C C
This European Standard was approved by CEN on 11 September 2003.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 4122:2004: E
worldwide for CEN national Members.

Contents                                                                         Page

Foreword.3
1 Scope .4
2 Normative references .4
3 Required characteristics.4
4 Designation .6
5 Marking .6
6 Technical specification .6
Foreword
This document (EN 4122:2004) has been prepared by the European Association of Aerospace
Manu
...