prEN 2087

SLOVENSKI STANDARD
01-september-2023
Aeronavtika - Aluminijeva zlitina AL-P2014A - T6 ali T62 - Pločevine in trakovi,
platirani - 0,4 mm ≤ a ≤ 6 mm
Aerospace series - Aluminium alloy AL-P2014A - T6 or T62 - Clad sheet and strip - 0,4
mm ≤ a ≤ 6 mm
Luft- und Raumfahrt - Aluminiumlegierung AL-P2014A - T6 oder T62 - Bleche und
Bänder, plattiert - 0,4 mm ≤ a ≤ 6 mm
Série aérospatiale - Alliage d'aluminium AL-P2014A - T6 ou T62 - Tôles et bandes
plaquées - 0,4 mm ≤ a ≤ 6 mm
Ta slovenski standard je istoveten z: prEN 2087
ICS:
49.025.20 Aluminij Aluminium
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2023
ICS 49.025.20 Will supersede EN 2087:2005
English Version
Aerospace series - Aluminium alloy AL-P2014A - T6 or
T62 - Clad sheet and strip - 0,4 mm  a  6 mm
Série aérospatiale - Alliage d'aluminium AL-P2014A - Luft- und Raumfahrt - Aluminiumlegierung AL-P2014A
T6 ou T62 - Tôles et bandes plaquées - 0,4 mm  a  6 - T6 oder T62 - Bleche und Bänder, plattiert - 0,4 mm 
mm a  6 mm
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee ASD-
STAN.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 2087:2023 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Requirements . 5
Annex A (informative) Standard evolution form . 9
Bibliography . 10

European foreword
This document (prEN 2087:2023) has been prepared by the Aerospace and Defence Industries
Association of Europe — Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this document has
received the approval of the National Associations and the Official Services of the member countries of
ASD-STAN, prior to its presentation to CEN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 2087:2005.
The main changes with respect to the previous edition are as follows:
— EN 2087 (P2), 10/2005 — Editorial improvements and update of Clause 2 “Normative references”.
— Correction of a typo in Table 1, line 2, as the max. value for Zr + Ti is meant to be 0,20 rather than
0,02.
— Addition of Annex A “Standard evolution form”. Addition of a bibliography.
Introduction
This document is part of the series of EN metallic material standards for aerospace applications.
The general organization of this series is described in EN 4258.
This document
...