EN 13443-1:2002+A1:2007
(Main)Water conditioning equipment inside buildings - Mechanical filters - Part 1: Particle rating 80 µm to 150 µm - Requirements for performances, safety and testing
Water conditioning equipment inside buildings - Mechanical filters - Part 1: Particle rating 80 µm to 150 µm - Requirements for performances, safety and testing
Part 1 of this European standard applies to mechanical filters for drinking water installations inside buildings, of nominal size from DN 15 to DN 100, minimum nominal pressure PN10, particle rating of 80 to 150 µm, and minimum design temperature of 30°C. It specifies requirements relating to the construction and mode of operation of filters and describes relevant methods of testing. It only concerns units which are permanently connected to the mains supply at the point of entry into the building.
Anlagen zur Behandlung von Trinkwasser innerhalb von Gebäuden - Mechanisch wirkende Filter - Teil 1: Filterfeinheit 80 µm bis 150 µm - Anforderungen an Ausführung, Sicherheit und Prüfung
Teil 1 dieser Europäischen Norm gilt für mechanisch wirkende Filter in der Trinkwasser-Installation innerhalb von Gebäuden mit einer Nennweite von DN 15 bis DN 100, einem minimalen Nenndruck von PN10, einer Durchlassweite 80 µm bis 150 µm und einer minimalen Auslegungstemperatur von 30 °C. Die Norm spezifiziert Anforderungen in Bezug auf Konstruktion und Funktion von Filtergeräten und beschreibt relevante Prüfverfahren. Sie bezieht sich nur auf fest installierte Geräte am Eintrittspunkt der Anschlussleitung in die Hausinstallation.
Teil 2 dieser Europäischen Norm (prEN 13443-2) ist ein weiteres Dokument und gilt für Filtergeräte mit einer Filterfeinheit geringer als 80 µm.
Appareils de traitement d'eau à l'intérieur des bâtiments - Filtres mécaniques - Partie 1: Particules de dimension comprise entre 80 µm et 150 µm - Exigences de performances et de sécurité, essais
La première partie de la présente Norme européenne s'applique aux filtres mécaniques utilisés dans les installations d'eau potable à l'intérieur des bâtiments, de diamètre nominal compris entre DN 15 et DN 100, de pression nominale PN 10, de seuil de filtration des particules compris entre 80 m et 150 m et de température opérationnelle minimale de 30 °C. Elle spécifie les exigences relatives à la fabrication et au mode de fonctionnement des filtres et décrit les méthodes d'essais adaptées. Elle ne concerne que les éléments raccordés en permanence au point d'entrée du réseau de distribution d'eau dans le bâtiment.
La seconde partie de la présente norme (prEN 13443-2) est un document séparé qui traite des filtres dont le seuil de filtration est limité aux particules de taille inférieure à 80 m.
Oprema, ki se uporablja za pripravo pitne vode v stavbah - Mehanski filtri - 1. del: Filtri za izločitev delcev z velikostjo 80 µm do 150 µm - Zahteve za delovanje, varnost in preskušanje
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Water conditioning equipment inside buildings - Mechanical filters - Part 1: Particle rating 80 µm to 150 µm - Requirements for performances, safety and testingAppareils de traitement d'eau a l'intérieur des bâtiments - Filtres mécaniques - Partie 1: Particules de dimension comprise entre 80 µm et 150 µm - Exigences de performances et de sécurité, essaisAnlagen zur Behandlung von Trinkwasser innerhalb von Gebäuden - Mechanisch wirkende Filter - Teil 1: Filterfeinheit 80 µm bis 150 µm - Anforderungen an Ausführung, Sicherheit und PrüfungTa slovenski standard je istoveten z:EN 13443-1:2002+A1:2007SIST EN 13443-1:2003+A1:2007en,fr,de91.140.60Sistemi za oskrbo z vodoWater supply systems13.060.20Pitna vodaDrinking waterICS:SLOVENSKI
STANDARDSIST EN 13443-1:2003+A1:200701-december-2007
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13443-1:2002+A1
September 2007 ICS 13.060.20; 91.140.60 Supersedes EN 13443-1:2002 English Version
Water conditioning equipment inside buildings - Mechanical filters - Part 1: Particle rating 80 µm to 150 µm - Requirements for performances, safety and testing
Appareils de traitement d'eau à l'intérieur des bâtiments - Filtres mécaniques - Partie 1: Particules de dimension comprise entre 80 µm et 150 µm - Exigences de performances et de sécurité, essais
Anlagen zur Behandlung von Trinkwasser innerhalb von Gebäuden - Mechanisch wirkende Filter - Teil 1: Filterfeinheit 80 µm bis 150 µm - Anforderungen an Ausführung, Sicherheit und Prüfung This European Standard was approved by CEN on 23 October 2002 and includes Amendment 1 approved by CEN on 9 August 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2007 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13443-1:2002+A1:2007: E
Bibliographical information.19 Annex B (normative)
!!!!Installation, operation and maintenance.22 Bibliography.26
(ISO 6509:1981) !deleted text" ! ISO 2591-1, Test sieving — Part 1: Methods using test sieves of woven wire cloth and perforated metal plate ISO 9276-1, Representation of results of particle size analysis — Part 1: Graphical representation ISO 13320-1, Particle size analysis — Laser diffraction methods — Part 1: General principles" 3 Terms and definitions For the purposes of this European Standard, the following terms and definitions apply. 3.1 !!!!drinking water"""" water intended for human consumption as defined in Directive 98/83/EC !(see Annex A)" 3.2 !!!!mechanical filter"""" !appliance" designed to remove undissolved substances from water, down to a specified particle size 3.3 filter element part of a filter designed to ensure the retention of particles
pressure drop does not exceed a value of 50 kPa (0,5 bar), or the filter surface velocity does not exceed the maximum specified value, whichever is lower 4 Classification 4.1 Principle Mechanical filters shall be designated by: nominal size DN; end connections; filter type; nominal pressure PN. The designation shall be clearly identified on the manufacturer's rating plate or in the instruction manual. Examples are given in !Annex A". 4.2 Nominal size (DN) The nominal size DN shall correspond to the flow rates in Table 2. The inlet connection of the filter may be DN or one size larger or one size smaller than the nominal size DN. In the case of flange connections the nominal size DN is determined by the DN of the inlet connection. 4.3 !!!!End connections"""" Examples of end connections are shown in !Annex A". Combinations of two kinds of connections are possible. 4.4 !!!!Filter type"""" Filters conforming to this standard shall be presented as one of the following types: filters requiring single use filter elements;
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.