EN ISO 14034:2018

SLOVENSKI STANDARD
01-januar-2019
Ravnanje z okoljem - Preverjanje okoljske tehnologije (ETV) (ISO 14034:2016)
Environmental management - Environmental technology verification (ETV) (ISO
14034:2016)
Umweltmanagement - Verifizierung von Umwelttechnologien (ETV) (ISO 14034:2016)
Management environnemental - Vérification des technologies environnementales (ETV)
(ISO 14034:2016)
Ta slovenski standard je istoveten z: EN ISO 14034:2018
ICS:
13.020.10 Ravnanje z okoljem Environmental management
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 14034
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2018
EUROPÄISCHE NORM
ICS 13.020.10
English Version
Environmental management - Environmental technology
verification (ETV) (ISO 14034:2016)
Management environnemental - Vérification des Umweltmanagement - Verifizierung von
technologies environnementales (ETV) (ISO Umwelttechnologien (ETV) (ISO 14034:2016)
14034:2016)
This European Standard was approved by CEN on 8 January 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14034:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
The text of ISO 14034:2016 has been prepared by Technical Committee 207 "Environmental
management” of the International Organization for Standardization (ISO) and has been taken over as
of which is held by CCMC.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2019, and conflicting national standards shall be
withdrawn at the latest by April 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 14034:2016 has been approved by CEN as EN ISO 14034:2018 without any modification.
INTERNATIONAL ISO
STANDARD 14034
First edition
2016-11-15
Environmental management —
Environmental technology
verification (ETV)
Management environnemental — Vérification des technologies
environnementales (ETV)
Reference number
ISO 14034:2016(E)
©
ISO 2016
ISO 14034:2016(E)
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

ISO 14034:2016(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
3.1 Terms related to organization. 1
3.2 Terms related to verification . 2
3.3 Terms related to technology . 2
3.4 Terms related to performance . 3
4 General principles and requirements . 4
4.1 Principles . 4
4.1.1 General. 4
4.1.2 Factual approach . 4
4.1.3 Sustainability . 4
4.1.4 Transparency and credibility . 4
4.1.5 Flexibility . 4
4.2 Requirements . 4
5 Environmental technology verification . 4
5.1 General . 4
5.2 Application . 5
5.2.1 Application requirements . 5
5.2.2 Application review . 6
5.3 Pre-verification . 6
5.3.1 Specification of performance to be verified . 6
5.3.2 Verification planning . 6
5.4 Verification . 7
5.4.1 General. 7
5.4.2 Acceptance of existing test data . 7
5.4.3 Generation of additional test data . 7
5.4.4 Confirmation of performance . 7
5.5 Reporting . 8
5.5.1 Verification report . 8
5.5.2 Verification statement . 8
5.6 Post-verification . 9
5.6.1 Publication . 9
5.6.2 Validity of the verification report/verification statement . 9
Annex A (informative) Relationship between ISO/IEC 17020:2012 and this document .10
Annex B (informative) Overview of environmental technology verification process .14
Annex C (informative) Guidance on the use of this document .16
Bibliography .25
ISO 14034:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given f
...