EN ISO 4210-2:2015
(Main)Cycles - Safety requirements for bicycles - Part 2: Requirements for city and trekking, young adult, mountain and racing bicycles (ISO 4210-2:2015)
Cycles - Safety requirements for bicycles - Part 2: Requirements for city and trekking, young adult, mountain and racing bicycles (ISO 4210-2:2015)
ISO 4210-2:2015 specifies safety and performance requirements for the design, assembly, and testing of bicycles and sub-assemblies having saddle height as given in Table 1, and lays down guidelines for manufacturer's instructions on the use and care of such bicycles.
This part of ISO 4210 applies to young adult bicycles with maximum saddle height of 635 mm or more and less than 750 mm, city and trekking bicycles, mountain bicycles, and racing bicycles that have a maximum saddle height of 635 mm or more including folding bicycles (see Table 1 and Figure 1).
This part of ISO 4210 does not apply to specialized types of bicycle, such as delivery bicycles, recumbent bicycles, tandems, BMX bicycles, and bicycles designed and equipped for use in severe applications such as sanctioned competition events, stunting, or aerobatic manoeuvres.
NOTE For bicycles with a maximum saddle height of 435 mm or less, see ISO 8124‑1, and with a maximum saddle height of more than 435 mm and less than 635 mm, see ISO 8098.
Fahrräder - Sicherheitstechnische Anforderungen an Fahrräder - Teil 2: Anforderungen für City- und Trekkingfahrräder, Jugendfahrräder, Geländefahrräder (Mountainbikes) und Rennräder (ISO 4210-2:2015)
Cycles - Exigences de sécurité des bicyclettes - Partie 2: Exigences pour bicyclettes de ville et de randonnée, de jeune adulte, de montagne et de course (ISO 4210-2:2015)
L'ISO 4210-2:2015 spécifie les exigences de sécurité et de performance à observer lors de la conception, de l'assemblage et des essais des bicyclettes et de leurs sous-ensembles et précise les lignes directrices concernant les instructions d'utilisation et d'entretien fournies par les fabricants de ces bicyclettes.
L'ISO 4210-2:2015 s'applique aux bicyclettes jeunes adultes ayant une hauteur maximale de selle supérieure ou égale à 635 mm et inférieure à 750 mm, aux bicyclettes de ville et tout chemin (trekking), aux bicyclettes tout terrain et aux bicyclettes de course ayant une hauteur maximale de selle supérieure ou égale à 635 mm, y compris les bicyclettes pliantes.
L'ISO 4210-2:2015 ne s'applique pas aux types spécialisés de bicyclettes comme les bicyclettes de livraison, les bicyclettes couchées, les tandems, les bicyclettes BMX et les bicyclettes conçues et équipées pour une utilisation dans des usages sévères telles que des compétitions réglementées, des cascades ou des figures acrobatiques.
Kolesa - Varnostne zahteve za kolesa - 2. del: Zahteve za mestna in treking kolesa, kolesa za mlade, gorska in tekmovalna kolesa (ISO 4210-2:2015)
Ta del standarda ISO 4210 določa varnostne in tehnične zahteve za zasnovo, sestavo in
preskušanje koles in njihovih podsestavov z višino sedeža, podano v preglednici 1, ter določa smernice za proizvajalčeva navodila za uporabo in nego takšnih koles.
Ta del standarda ISO 4210 velja za kolesa za mlade z maksimalno višino sedeža najmanj 635 mm in največ 750 mm, mestna in treking kolesa, gorska kolesa in tekmovalna kolesa z maksimalno višino sedeža najmanj 635 mm, vključno z zložljivimi kolesi (glejte preglednico 1 in sliko 1).
Ta del standarda ISO 4210 ne velja za specializirane vrste koles, na primer dostavna kolesa, ležeča kolesa, tandemska kolesa, kolesa BMX in kolesa, zasnovana in opremljena za uporabo v zahtevnih pogojih, na primer na sankcioniranih tekmovanjih, za izvajanje trikov in akrobacij.
OPOMBA Za kolesa z maksimalno višino sedeža 435 mm ali manj glejte standard ISO 8124-1, za kolesa z maksimalno višino sedeža najmanj 435 mm in največ 635 mm pa glejte standard ISO 8098.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2015
1DGRPHãþD
SIST EN ISO 4210-2:2014
Kolesa - Varnostne zahteve za kolesa - 2. del: Zahteve za mestna in treking kolesa,
kolesa za mlade, gorska in tekmovalna kolesa (ISO 4210-2:2015)
Cycles - Safety requirements for bicycles - Part 2: Requirements for city and trekking,
young adult, mountain and racing bicycles (ISO 4210-2:2015)
Fahrräder - Sicherheitstechnische Anforderungen an Fahrräder - Teil 2: Anforderungen
für City- und Trekkingfahrräder, Jugendfahrräder, Geländefahrräder (Mountainbikes) und
Rennräder (ISO 4210-2:2015)
Cycles - Exigences de sécurité des bicyclettes - Partie 2: Exigences pour bicyclettes de
ville et de randonnée, de jeune adulte, de montagne et de course (ISO 4210-2:2015)
Ta slovenski standard je istoveten z: EN ISO 4210-2:2015
ICS:
43.150 Kolesa Cycles
97.220.40 Oprema za športe na Outdoor and water sports
prostem in vodne športe equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 4210-2
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2015
EUROPÄISCHE NORM
ICS 43.150 Supersedes EN ISO 4210-2:2014
English Version
Cycles - Safety requirements for bicycles - Part 2:
Requirements for city and trekking, young adult, mountain
and racing bicycles (ISO 4210-2:2015)
Cycles - Exigences de sécurité des bicyclettes - Partie 2: Fahrräder - Sicherheitstechnische Anforderungen an
Exigences pour bicyclettes de ville et de randonnée, de Fahrräder - Teil 2: Anforderungen für City- und
jeune adulte, de montagne et de course (ISO 4210- Trekkingfahrräder, Jugendfahrräder, Geländefahrräder
2:2015) (Mountainbikes) und Rennräder (ISO 4210-2:2015)
This European Standard was approved by CEN on 8 August 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4210-2:2015 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 4210-2:2015) has been prepared by Technical Committee ISO/TC 149 “Cycles”
in collaboration with Technical Committee CEN/TC 333 “Cycles” the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2016, and conflicting national standards shall
be withdrawn at the latest by March 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 4210-2:2014.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 4210-2:2015 has been approved by CEN as EN ISO 4210-2:2015 without any
modification.
INTERNATIONAL ISO
STANDARD 4210-2
Second edition
2015-09-01
Cycles — Safety requirements for
bicycles —
Part 2:
Requirements for city and trekking,
young adult, mountain and racing
bicycles
Cycles — Exigences de sécurité des bicyclettes —
Partie 2: Exigences pour bicyclettes de ville et de randonnée, de jeune
adulte, de montagne et de course
Reference number
ISO 4210-2:2015(E)
©
ISO 2015
ISO 4210-2:2015(E)
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
ISO 4210-2:2015(E)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 2
4 Requirements . 2
4.1 Toxicity . 2
4.2 Sharp edges . 2
4.3 Security and strength of safety-related fasteners . 2
4.3.1 Security of screws . 2
4.3.2 Minimum failure torque . 3
4.3.3 Folding bicycle mechanism . 3
4.4 Crack detection methods . 3
4.5 Protrusions . 3
4.6 Brakes . 3
4.6.1 Braking systems. 3
4.6.2 Hand-operated brakes . 4
4.6.3 Attachment of brake assembly and cable requirements . 5
4.6.4 Brake-block and brake-pad assemblies — Security test . 5
4.6.5 Brake adjustment . 6
4.6.6 Hand-operated braking-system — Strength test . 6
4.6.7 Back-pedal braking system — Strength test . 6
4.6.8 Braking performance . 6
4.6.9 Brakes — Heat-resistance test . 9
4.7 Steering . 9
4.7.1 Handlebar — Dimensions . 9
4.7.2 Handlebar grips and plugs .10
4.7.3 Handlebar stem — Insertion-depth mark or positive stop .10
4.7.4 Handlebar stem to fork steerer — Clamping requirements . .10
4.7.5 Steering stability .11
4.7.6 Steering assembly — Static strength and security tests . .11
4.7.7 Handlebar and stem assembly — Fatigue test .13
4.8 Frames .13
4.8.1 Suspension-frames — Special requirements .13
4.8.2 Frame — Impact test (falling mass) .13
4.8.3 Frame and front fork assembly — Impact test (falling frame) .14
4.8.4 Frame — Fatigue test with pedalling forces .14
4.8.5 Frame — Fatigue test with horizontal forces .14
4.8.6 Frame — Fatigue test with a vertical force .14
4.9 Front fork .14
4.9.1 General.14
4.9.2 Means of location of the axle and wheel retention .14
4.9.3 Suspension forks — Special requirements .15
4.9.4 Front fork — Static bending test .15
4.9.5 Front fork — Rearward impact test .15
4.9.6 Front fork — Bending fatigue test plus rearward impact test.15
4.9.7 Forks intended for use with hub- or disc-brakes .16
4.9.8 Tensile test for a non-welded fork .16
4.10 Wheels and wheel/tyre assembly .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.