EN 13445-4:2021+A1:2023
(Main + Amendment)Unfired pressure vessels - Part 4: Fabrication
Unfired pressure vessels - Part 4: Fabrication
This document specifies requirements for the manufacture of unfired pressure vessels and their parts, made of steels, including their connections to non-pressure parts. It specifies requirements for material traceability, manufacturing tolerances, welding requirements, requirements for permanent joints other than welding, production tests, forming requirements, heat treatment, repairs and finishing operations.
Unbefeuerte Druckbehälter - Teil 4: Herstellung
Dieses Dokument enthält Anforderungen an die Herstellung von unbefeuerten Druckbehältern und Druckbehälterteilen aus Stählen, einschließlich deren Verbindungen zu nicht drucktragenden Teilen. Es enthält Anforderungen an die Rückverfolgbarkeit von Werkstoffen, Fertigungstoleranzen, Schweißanforderungen, Anforderungen an nicht geschweißte dauerhafte Verbindungen, Arbeitsproben, Umformanforderungen, Wärmebehandlung, Reparaturen und Fertigbearbeitung.
Récipients sous pression non soumis à la flamme - Partie 4 : Fabrication
Le présent document spécifie les exigences relatives à la fabrication des récipients sous pression non soumis à la flamme et de leurs parties sous pression, réalisés en acier, y compris leur raccordement avec des parties non soumises à la pression. Il spécifie des exigences concernant la traçabilité des matériaux, les tolérances de fabrication, les exigences de soudage, les exigences concernant les assemblages permanents autres que le soudage, les coupons-témoins, les exigences de formage, les traitements thermiques, les réparations, et la finition.
Nekurjene tlačne posode - 4. del: Proizvodnja (vključuje dopolnilo A1)
Ta dokument določa zahteve za proizvodnjo nekurjenih tlačnih posod in njihovih delov, izdelanih iz jekel, vključno z njihovimi priključki na netlačne dele. Določa zahteve za sledljivost materiala, proizvodna odstopanja, zahteve za varjenje, zahteve za trajne spoje, ki niso varjeni, proizvodne preskuse, zahteve za oblikovanje, toplotno obdelavo, popravila in zaključne operacije.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2023
Nadomešča:
SIST EN 13445-4:2021
SIST EN 13445-4:2021/A1:2023
Nekurjene tlačne posode - 4. del: Proizvodnja (vključuje dopolnilo A1)
Unfired pressure vessels - Part 4: Fabrication
Unbefeuerte Druckbehälter - Teil 4: Herstellung
Récipients sous pression non soumis à la flamme - Partie 4 : Fabrication
Ta slovenski standard je istoveten z: EN 13445-4:2021+A1:2023
ICS:
23.020.32 Tlačne posode Pressure vessels
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 13445-4:2021+A1
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2023
EUROPÄISCHE NORM
ICS 23.020.30
English Version
Unfired pressure vessels - Part 4: Fabrication
Récipients sous pression non soumis à la flamme - Unbefeuerte Druckbehälter - Teil 4: Herstellung
Partie 4 : Fabrication
This European Standard was approved by CEN on 24 February 2021 and includes Amendment 1 approved by CEN on 3 March
2023 and Amendment 1 approved by CEN on 13 June 2023.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13445-4:2021+A1:2023 E
worldwide for CEN national Members.
Contents
Page
European foreword . 5
1 Scope . 5
2 Normative references . 7
3 Terms and definitions . 8
4 Requirements for manufacturing and subcontracting . 8
4.1 Manufacturing . 8
4.2 Subcontracting . 9
5 Materials . 9
5.1 General . 9
5.2 Material traceability . 9
5.2.1 General . 9
5.2.2 Identification system . 9
5.2.3 Visibility. 10
5.2.4 Review of material certification and material identification . 10
5.2.5 Transfer of markings . 10
6 Manufacturing tolerances . 11
6.1 Surface geometry of welds . 11
6.2 Middle line alignment . 11
6.3 Surface alignment . 13
6.3.1 Surface misalignment between parts . 13
6.3.2 Joining of parts of different thickness . 13
6.4 Tolerances for vessels subjected to internal pressure . 13
6.4.1 External diameter . 13
6.4.2 Out of roundness . 13
6.4.3 Deviation from the longitudinal axis . 14
6.4.4 Irregularities in profile . 14
6.4.5 Local thinning . 16
6.4.6 Dished ends . 17
6.5 Tolerances for vessels subjected to external pressure . 20
6.6 Structural tolerances . 20
7 Weld details . 20
7.1 General . 20
7.2 Vessels or parts made of more than one course . 20
7.3 Lapped joints, joggle joints, permanent backing strips . 20
8 Welding . 20
8.1 General . 20
8.2 Welding procedure specification (WPS) . 21
8.3 Welding procedure qualification record (WPQR) . 21
8.4 Qualification of welders and welding operators . 22
8.5 Filler metals and auxiliary materials . 23
8.6 Joint preparation . 23
8.7 Execution of welded joints . 24
8.8 Attachments, supports and stiffeners . 24
8.9 Preheat . 24
8.10 Permanent joints other than welding . 24
8.10.1 General . 24
8.10.2 Mechanical roller expansion . 25
8.10.3 Brazing . 25
9 Manufacture and testing of welds — Production test . 25
9.1 General . 25
9.2 Reference criteria . 26
9.3 Extent of testing . 30
9.4 Performance of tests and acceptance criteria . 32
9.4.1 General . 32
9.4.2 Transverse tensile test . 32
9.4.3 Longitudinal weld tensile test . 32
9.4.4 Impact test . 32
9.4.5 Bend test . 32
9.4.6 Macro examination . 33
9.4.7 Micro examination . 33
9.4.8 Hardness test . 33
9.4.9 Retests . 33
9.4.10 Test report . 34
10 Forming of pressure parts . 34
10.1 General . 34
10.2 Ratio of deformation . 34
10.2.1 Dished circular products . 34
10.2.2 Cylinders and cones made by rolling . 35
10.2.3 Other product types . 36
10.2.4 Tube bends . 37
10.2.5 Forming of Segments . 37
10.3 Forming procedures . 38
10.3.1 Cold forming . 38
10.3.2 Hot forming . 39
10.4 Heat treatment after forming . 41
10.4.1 General .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.