EN 13042-1:2007/FprA1

SLOVENSKI STANDARD
01-junij-2009
Stroji in obrati za proizvodnjo, obdelavo in predelavo votlega stekla - Varnostne
zahteve - 1. del: Dovajalnik za regulacijo kaplje
Machines and plants for the manufacture, treatment and processing of hollow glass -
Safety requirements - Part 1: Gob feeder
Maschinen und Anlagen für die Herstellung, Be- und Verarbeitung von Hohlglas -
Sicherheitsanforderungen - Teil 1: Tropfenspeiser
Machines et installations pour la production, le façonnage et la transformation du verre
creux - Exigences de sécurité - Partie 1: Mécanisme d'alimentation en paraisons
Ta slovenski standard je istoveten z: EN 13042-1:2007/FprA1
ICS:
81.100 2SUHPD]DVWHNODUVNRLQ Equipment for the glass and
NHUDPLþQRLQGXVWULMR ceramics industries
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
FINAL DRAFT
EN 13042-1:2007
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
April 2009
ICS 81.100
English Version
Machines and plants for the manufacture, treatment and
processing of hollow glass - Safety requirements - Part 1: Gob
feeder
Machines et installations pour la production, le façonnage Maschinen und Anlagen für die Herstellung, Be- und
et la transformation du verre creux - Exigences de sécurité Verarbeitung von Hohlglas - Sicherheitsanforderungen -
- Partie 1: Mécanisme d'alimentation en paraisons Teil 1: Tropfenspeiser
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 151.
This draft amendment A1, if approved, will modify the European Standard EN 13042-1:2007. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13042-1:2007/FprA1:2009: E
worldwide for CEN national Members.

Contents Page
Foreword .3
1 Modification to the Foreword .3
2 Modification to the Scope .3
3 Modifications to Clause 2 .3
4 Modifications to Clause 5 .4
5 Modification to Clause 6 .6
6 Modifications to Clause 7 .6
7 Addition of Annex ZB .7
8 Modification to the Bibliography .7

Foreword
This document (EN 13042-1:2007/FprA1:2009) has been prepared by Technical Committee CEN/TC 151
“Construction equipment and building material machines — Safety”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EC Directive(s).
For relationship with EC Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.
1 Modification to the Foreword
th
Replace the 4 paragraph with the following:
”For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.”
2 Modification to the Scope
Replace 1.2 with the following:
“1.2 This European Standard deals with the significant hazards, hazardous situations and events relevant to
gob feeders, when they are used as intended and under the conditions of misuse which are reasonably fore-
seeable by the manufacturer (see Clause 4). Noise is not a significant hazard for this type of machine. This
European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the
significant hazards during commissioning, operation and maintenance.”
3 Modifications to Clause 2
Delete the following references:
“EN 418:1992, Safety of machinery — Emergency stop equipment, functional aspects — Principles for design
EN 954-1:1996, Safety of machinery — Safety-related parts of control systems — Part 1: General principles
for design
EN 1050:1996, Safety of machinery — Principles for risk assessment”.
Add the following references:
“EN ISO 11201:1995, Acoustics — Noise emitted by machinery and equipment — Measurement of emission
sound pressure levels at a work station and at other specified positions — Engineering method in an essen-
tially free field over a reflecting plane (ISO 11201:1995)
EN ISO 11202:1995, Acoustics — Noise emitted by machinery and equipment — Measurement of emission
sound pressure levels at a work station and at other specified positions — Survey method in situ
(ISO 11202:1995)
EN ISO 11204:1995, Acoustics — Noise emitted by machinery and equipment — Measurement of emission
sound pressure levels at a work station and at other specified positions — Method requiring environmental
corrections (ISO 11204:1995)
EN ISO 13849-1:2008, Safety of machinery — Safety-related parts of control systems — Part 1: General prin-
ciples for design (ISO 13849-1:2006)
EN ISO 13850:2008, Safety of machinery — Emergency stop — Principles for design (ISO 13850:2006)
EN ISO 4871:1996, Acoustics — Declaration and verification of noise emission values of machinery and
equipment (ISO 4871:1996)”.
4 Modifications to Clause 5
rd
In 5.1, replace the 3 paragraph with the following:
“For applications of a B-level standard such as EN 953, EN 982, EN 983, EN 1037, EN 60204-1 and
EN ISO 13850, the manufacturer shall carry out an adequate risk assessment for the requirements thereof
where choice is necessary. This specific risk assessment is part of the general risk assessment relating to the
...