EN 13042-2:2004/prA1

SLOVENSKI STANDARD
01-februar-2009
Stroji in obrati za proizvodnjo, obdelavo in predelavo votlega stekla - Varnostne
zahteve - 2. del: Upravljalni stroji za podajanje
Machines and plants for the manufacture, treatment and processing of hollow glass -
Safety requirements - Part 2: Handling machines for feeding
Maschinen und Anlagen zur Herstellung, Be- und Verarbeitung von Hohlglas -
Sicherheitsanforderungen - Teil 2: Handhabungsmaschinen zum Speisen
Machines et installations pour la production, le façonnage et la transformation du verre
creux - Exigences de sécurité - Partie 2: Machines pour charger
Ta slovenski standard je istoveten z: EN 13042-2:2004/prA1
ICS:
81.100 2SUHPD]DVWHNODUVNRLQ Equipment for the glass and
NHUDPLþQRLQGXVWULMR ceramics industries
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
FINAL DRAFT
EN 13042-2:2004
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
December 2008
ICS 81.100
English Version
Machines and plants for the manufacture, treatment and
processing of hollow glass - Safety requirements - Part 2:
Handling machines for feeding
Machines et installations pour la production, le façonnage Maschinen und Anlagen zur Herstellung, Be- und
et la transformation du verre creux - Exigences de sécurité Verarbeitung von Hohlglas - Sicherheitsanforderungen -
- Partie 2: Machines pour charger Teil 2: Handhabungsmaschinen zum Speisen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 151.
This draft amendment A1, if approved, will modify the European Standard EN 13042-2:2004. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13042-2:2004/prA1:2008: E
worldwide for CEN national Members.

Contents Page
Foreword.3
1 Modification to the Introduction.4
2 Modification to the Scope .4
3 Modification to Clause 2 .4
4 Modification to Clause 3 .5
5 Modification to 5.1 .5
6 Modification to 5.3 .5
7 Modification to 5.3.1 .5
8 Modification to 5.3.2.2 .6
9 Modification to 5.5 .6
10 Modification to 5.9 .6
11 Modification to 5.9.2 .6
12 Modification to 5.9.9.2 .6
13 Modification to 5.9.10 .6
14 Modification to 5.9.10.1 .7
15 Modification to 5.9.10.2 .7
16 Modification to 5.9.11 .7
17 Addition of 5.10.7
18 Modification to Clause 6 .8
19 Modification to 7.3.1 .9
20 Addition of 7.3.11.9
21 Addition of 7.3.12.9
22 Modifications to 7.4 .9
23 Addition of Annex ZB .10
24 Modifications to the Bibliography.10

Foreword
This document (EN 13042-2:2004/prA1:2008) has been prepared by Technical Committee CEN/TC 151
“Construction equipment and building material machines — Safety”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EC Directive(s).
For relationship with EC Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.
1 Modification to the Introduction
st
In the 1 paragraph, replace the reference to “EN 1070” with “EN ISO 12100-1”.
2 Modification to the Scope
Replace 1.2 with the following:
“1.2 This European Standard deals with all significant hazards, hazardous situations and events relevant to
handling machines for feeding, when they are used as intended and under the conditions of misuse which are
reasonably foreseeable by the manufacturer (see Clause 4). This European Standard specifies the appropri-
ate technical measures to eliminate or reduce risks arising from significant hazards during commissioning,
operation and maintenance.”
Replace 1.3 with the following:
"1.3 This European Standard does not deal with feeding with shears alone, with the transport of the melted
glass post by its own weight in free fall or by trueing (gob feeder, see EN 13042-1)."
3 Modification to Clause 2
Replace:
"EN 294:1992, Safety of machinery — Safety distance to prevent danger zones being reached by the upper
limbs"
with the following reference:
"EN ISO 113857:2008, Safety of machinery – Safety distances to prevent hazard zones being reached by up-
per and lower limbs (ISO 13857:2008)"
Delete the following references:
“EN 954-1:1996, Safety of machinery — Safety-related parts of control systems — Part 1: General principles
for design”
“EN 1050:1996, Safety of machinery — Principles for risk assessment"
"EN 1070:1998, Safety of machinery — Terminology”
Update EN 60204-1:1997 as follows:
“EN 60204-1:2006, Safety of machinery — Electrical equipment of machines — Part 1: General requirements
(IEC 60204-1:2005, modified)”.
Add the following references:
“EN 61496-1:2004, Safety of machinery — Electro-sensitive protective equipment — Part 1: General require-
ments and tests (IEC 61496-1:2004, modified)"
"EN ISO 11201:1995, Acoustics — Noise emitted by machinery and equipment — Measurement of emission
sound pressure levels at a work station and at other specified positions — Engineering method in an essen-
tially free field over a reflecting plane (ISO 11201:1995)"
"EN ISO 11202:1995, Acoustics — Noise emitted by machinery and equipment — Measuremen
...