EN ISO 19076:2023

SLOVENSKI STANDARD
01-april-2023
Usnje - Merjenje usnjene površine - Elektronske tehnike (ISO 19076:2023)
Leather - Measurement of leather surface - Electronic techniques (ISO 19076:2023)
Leder - Messung der Oberfläche des Leders - Elektronische Verfahren (ISO 19076:2023)
Cuir - Mesurage de la surface du cuir - Techniques électroniques (ISO 19076:2023)
Ta slovenski standard je istoveten z: EN ISO 19076:2023
ICS:
59.140.30 Usnje in krzno Leather and furs
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 19076
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2023
EUROPÄISCHE NORM
ICS 59.140.30 Supersedes EN ISO 19076:2016
English Version
Leather - Measurement of leather surface - Electronic
techniques (ISO 19076:2023)
Cuir - Mesurage de la surface du cuir - Techniques Leder - Messung der Oberfläche des Leders -
électroniques (ISO 19076:2023) Elektronische Verfahren (ISO 19076:2023)
This European Standard was approved by CEN on 22 January 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19076:2023 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 19076:2023) has been prepared by Technical Committee ISO/IULTCS
"International Union of Leather Technologists and Chemists Societies" in collaboration with Technical
Committee CEN/TC 289 “Leather” the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2023, and conflicting national standards shall
be withdrawn at the latest by August 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 19076:2016.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 19076:2023 has been approved by CEN as EN ISO 19076:2023 without any modification.

INTERNATIONAL ISO
STANDARD 19076
IULTCS
IUP 58
Second edition
2023-01
Leather — Measurement of leather
surface — Electronic techniques
Cuir — Mesurage de la surface du cuir — Techniques électroniques
Reference numbers
ISO 19076:2023(E)
IULTCS/IUP 58:2023(E)
ISO 19076:2023(E)
IULTCS/IUP 58:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 19076:2023(E)
IULTCS/IUP 58:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus and materials .2
5.1 Measuring machines. 2
5.1.1 General . 2
5.1.2 Measuring machine types with linear sensor array (types A, B and C) . 2
5.1.3 Type A roller measuring machine . 3
5.1.4 Roller measuring machine with transport roller (type A1) . 3
5.1.5 Roller measuring machine with transport conveyor (type A2) . 3
5.1.6 Conveyor measuring machine (type B) . 4
5.1.7 Standard conveyor measuring machine (type B1) . . 4
5.1.8 Vacuum tape conveyor measuring machine (type B2) . 4
5.1.9 Flatbed scanning machines (type C) . 4
5.1.10 Camera measuring machine (type D) . 5
5.2 Reference calibrated templates for machine verification . 5
6 Sampling and conditioning . 5
7 General measurement criteria .6
7.1 General requirement . 6
7.2 Leather orientation during measurement . 6
7.2.1 General . 6
7.2.2 Measuring whole leather pieces . 6
7.2.3 Measuring half-leather pieces . 6
7.2.4 Measuring leather cut pieces . . 7
7.3 Measurement operations . 7
7.3.1 Roller machines . 7
7.3.2 Conveyor machines . 7
7.3.3 Flatbed scanner machines and bi-dimensional static measuring devices. 8
8 Measurement procedure . 8
9 Calculation and expression of results . 9
10 Test report . 9
Annex A (normative) Manufacturing characteristics of calibrated templates for the
verification of electronic measuring machines .11
Annex B (normative) Procedure for the verification of a measuring machine by calibrated
templates .13
Annex C (normative) Laboratory record of calibrated templates .15
Annex D (informative) Repeatability and reproducibility .16
Annex E (informative) Pickled and wet leather conditioning before testing .18
Bibliography .19
iii
ISO 19076:2023(E)
IULTCS/IUP 58:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given
...