EN 3716-004:2014

SLOVENSKI STANDARD
01-februar-2015
1DGRPHãþD
SIST EN 3716-004:2009
$HURQDYWLND.RQHNWRUMLHQRSROQLVWULRVQLPYPHVQLNRP]DGLJLWDOQLSUHQRV
SRGDWNRYGHO6SDMNDOQLYWLþLQSULNOMXþHN6WDQGDUG]DSURL]YRG
Aerospace series - Connectors, single-way with triaxial interface for transmission of
digital data - Part 004: Solder plug and terminator - Product standard
Luft- und Raumfahrt - Steckverbinder, einpolig, triaxial für digitale Datenübertragung -
Teil 004: Freier Steckverbinder lätbar und Abschlusswiderstand - Produktnorm
Série aérospatiale - Connecteur, monovoie, avec interface triaxiale, pour transmission de
données numériques - Partie 004: Fiche à souder et impédance de terminaison - Norme
de produit
Ta slovenski standard je istoveten z: EN 3716-004:2014
ICS:
49.060 /HWDOVNDLQYHVROMVND Aerospace electric
HOHNWULþQDRSUHPDLQVLVWHPL equipment and systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 3716-004
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2014
ICS 49.060; 49.090 Supersedes EN 3716-004:2006
English Version
Aerospace series - Connectors, single-way with triaxial interface
for transmission of digital data - Part 004: Solder plug and
terminator - Product standard
Série aérospatiale - Connecteur, monovoie, avec interface Luft- und Raumfahrt - Steckverbinder, einpolig, triaxial für
triaxiale, pour transmission de données numériques - Partie digitale Datenübertragung - Teil 004: Freier Steckverbinder
004: Fiche à souder et impédance de terminaison - Norme lätbar und Abschlusswiderstand - Produktnorm
de produit
This European Standard was approved by CEN on 22 November 2014.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 3716-004:2014 E
worldwide for CEN national Members.

Contents Page
Foreword .3
1 Scope .4
2 Normative references .4
3 Terms and definitions .4
4 Required characteristics .5
4.1 Dimensions and mass .5
4.1.1 Dimensions .5
4.1.2 Mass .6
4.2 Material and surface treatment .6
4.3 Main general characteristics .6
4.4 Plug and receptacle combination options .7
5 Technical specification .7
6 Designation .7
6.1 Connector (see Figure 1) .7
6.2 Terminator (see Figure 2 and Figure 3) .7
7 Marking .8
7.1 Connector .8
7.2 Terminator .8
8 Assembly instructions .8
8.1 Tooling .8
8.2 Procedure .8
8.3 Procedure with screen connection .9
8.4 Procedure without screen connection . 10

Foreword
This document (EN 3716-004:2014) has been prepared by the Aerospace and Defence Industries Association
of Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of ASD,
prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2015, and conflicting national standards shall be withdrawn at
the latest by June 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 3716-004:2006.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, Fra
...