EN 1865-3:2012/FprA1
(Amendment)Patient handling equipment used in road ambulances - Part 3: Heavy duty stretcher
Patient handling equipment used in road ambulances - Part 3: Heavy duty stretcher
This European Standard specifies minimum requirements for the design and performance of heavy duty stretchers used in road ambulances for the treatment and transportation of patients. It aims to ensure patient safety and minimize the physical effort required by staff operating the equipment.
Krankentransportmittel im Krankenkraftwagen - Teil 3: Schwerlastkrankentrage
Equipement d'ambulances pour le transport de patients - Partie 3 : Brancard bariatrique
Oprema za ravnanje s pacienti v reševalnih vozilih - 3. del: Bolniška nosila za večje obremenitve
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2014
2SUHPD]DUDYQDQMHVSDFLHQWLYUHãHYDOQLKYR]LOLKGHO%ROQLãNDQRVLOD]DYHþMH
REUHPHQLWYH
Patient handling equipment used in road ambulances - Part 3: Heavy duty stretcher
Krankentransportmittel im Krankenkraftwagen - Teil 3: Schwerlastkrankentrage
Equipement d'ambulances pour le transport de patients - Partie 3 : Brancard bariatrique
Ta slovenski standard je istoveten z: EN 1865-3:2012/FprA1
ICS:
11.160 3UYDSRPRþ First aid
43.160 Vozila za posebne namene Special purpose vehicles
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
FINAL DRAFT
EN 1865-3:2012
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
June 2014
ICS 11.160
English Version
Patient handling equipment used in road ambulances - Part 3:
Heavy duty stretcher
Equipement d'ambulances pour le transport de patients - Krankentransportmittel im Krankenkraftwagen - Teil 3:
Partie 3 : Brancard bariatrique Schwerlastkrankentrage
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 239.
This draft amendment A1, if approved, will modify the European Standard EN 1865-3:2012. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1865-3:2012/FprA1:2014 E
worldwide for CEN national Members.
Contents Page
Foreword .3
1 Modification to the Introduction .4
2 Modifications to Clause 2, Normative References .4
3 Modification to Clause 3, Terms and definitions .4
4 Modifications to 4.1, General .4
5 Modifications to 4.2, Dimensions .4
6 Modification to 4.3, Mass .5
7 Modification to 4.5.4, Power source.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.