EN 10152:2009
(Main)Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions
Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions
This European Standard specifies requirements for continuously electrolytic zinc coated cold rolled flat products of low carbon steels suitable for cold forming according to Table 1 in rolled widths above or equal to 600 mm and thicknesses from 0,35 mm up to and including 3 mm, delivered as strip (in coil form), sheet, slit strip or cut lengths obtained from slit strip or sheet.
NOTE 1 This European Standard can also be applied to continuously electrolytic zinc coated flat products of:
a) steels according to EN 10139 (cold rolled strip in rolled widths < 600 mm),
b) steels normally characterized by minimum yield strength or minimum tensile strength values in addition to formability parameters, e. g.
1) steels with high yield strength and improved formability according to EN 10268 (cold rolled flat products),
2) multiphase steels (cold rolled or hot rolled) according to prEN 10338,
3) steels for construction according to national or regional standards (see e. g. DIN 1623).
NOTE 2 By agreement at the time of enquiry and order this European Standard can be applied to continuously electrolytic zinc coated hot-rolled steel flat products (e.g. according to EN 10025-1 and -2, EN 10111, EN 10149-1 to EN 10149-3, etc.).
NOTE 3 As the mass of the zinc coating applied is relatively small, the material is not intended to withstand outside exposure without further chemical treatment and painting.
Elektrolytisch verzinkte kaltgewalzte Flacherzeugnisse aus Stahl zum Kaltumformen - Technische Lieferbedingungen
Diese Europäische Norm legt die Anforderungen an kontinuierlich elektrolytisch verzinkte, kaltgewalzte Flacherzeugnisse
aus weichen Stählen zum Kaltumformen nach Tabelle 1 in gewalzten Breiten ≥ 600 mm und mit
einer Dicke von 0,35 mm bis 3 mm fest, die als Band (in Rollen), Blech, längs geteiltes Band oder daraus
abgelängte Stäbe geliefert werden.
ANMERKUNG 1 Diese Europäische Norm kann auch auf kontinuierlich elektrolytisch verzinkte, kaltgewalzte
Flacherzeugnisse aus
a) Stählen nach EN 10139 (Kaltband in Walzbreiten < 600 mm),
b) Stählen, die üblicherweise in Ergänzung zu den Anforderungen an die Umformbarkeit durch Mindestwerte für die
Streckgrenze oder Zugfestigkeit gekennzeichnet sind, z. B.
⎯ Stähle mit hoher Streckgrenze und verbesserter Umformbarkeit nach EN 10268 (kaltgewalzte Flacherzeugnisse),
⎯ Mehrphasenstähle (kaltgewalzt oder warmgewalzt) nach prEN 10338,
⎯ Stähle für die Anwendung im Bauwesen nach nationalen oder regionalen Normen (siehe z. B. DIN 1623)
angewendet werden.
ANMERKUNG 2 Nach Vereinbarung bei der Anfrage und Bestellung kann diese Europäische Norm auf kontinuierlich
elektrolytisch verzinkte, warmgewalzte Flacherzeugnisse aus Stahl (z. B. nach EN 10025, EN 10111, EN 10149-1 bis
EN 10149-3 usw.) angewendet werden.
ANMERKUNG 3 Da die Masse der Zinkauflage verhältnismäßig klein ist, sind die Erzeugnisse nicht ohne weitere
chemische Behandlung und Beschichtungen für die Verwendung im Außeneinsatz vorzusehen.
Produits plats en acier, laminés à froid, revêtus de zinc par voie électrolytique pour formage à froid - Conditions techniques de livraison
La présente Norme européenne définit les prescriptions relatives aux produits plats laminés à froid revêtus
de zinc en continu par voie électrolytique, en aciers à bas carbone aptes au formage à froid selon les
indications du Tableau 1, en largeurs laminées ≥ 600 mm et en épaisseurs comprises entre 0,35 mm et 3 mm
inclus, livrés sous forme de bandes (en bobines), de tôles, de bandes refendues coupées à longueur ou non
ou dans des tôles.
NOTE 1 La présente Norme européenne peut également s'appliquer aux produits plats revêtus de zinc en continu, par
voie électrolytique, en :
a) aciers conformes à l'EN 10139 (feuillards laminés à froid en largeurs de laminage < 600 mm),
b) aciers normalement caractérisés par une valeur minimale de limite d'élasticité ou de résistance à la traction en plus
de leur aptitude au formage et par exemple ;
- aciers à haute limite d'élasticité et à formabilité améliorée conformes à l’EN 10268 (produits plats laminés à
froid) ;
- aciers multiphasés (laminés à froid ou laminés à chaud) conformes au prEN 10338 ;
- aciers pour la construction conformes aux normes nationales ou régionales (voir par exemple DIN 1623).
NOTE 2 Par accord au moment de l’appel d’offres et à la commande, cette Norme européenne peut être appliquée aux
produits plats laminés à chaud revêtus de zinc en continu par voie électrolytique (par exemple, conforme aux normes EN
10025-1 et -2, EN 10111, EN 10149-1 à EN 10149-3, etc.).
NOTE 3 Comme la masse du revêtement de zinc appliqué est relativement faible, le matériau n'est pas censé résister
à une exposition extérieure sans traitement chimique supplémentaire et application de peinture.
Elektrolizno cinkani hladno valjani ploščati izdelki za hladno preoblikovanje - Tehnični dobavni pogoji
Ta evropski standard določa zahteve za trajno elektrolizno cinkane hladno valjane ploščate izdelke iz maloogljičnega jekla, primerne za hladno preoblikovanje v skladu s preglednico 1, z valjano širino ≥ 600 mm in debelino od 0,35 mm do vključno 3 mm, dobavljene v obliki traka (zvitki), pločevine, razrezanega traka ali narezanih dolžin iz razrezanega traka oziroma pločevine. OPOMBA 1: Ta evropski standard se lahko uporablja za trajno elektrolizno cinkane ploščate izdelke iz:
a) jekla v skladu s standardom EN 10139 (hladno valjan trak v valjanih širinah < 600 mm),
b) jekla, ki ga poleg parametrov oblikovalnosti običajno opredeljujejo najmanjše vrednosti meje tečenja ali natezne trdnosti , npr.
1) jekla z visoko mejo tečenja in izboljšano oblikovalnostjo v skladu s standardom EN 10268 (hladno valjani ploščati izdelki),
2) večfazna jekla (hladno valjana ali vroče valjana) v skladu s standardom prEN 10338,
3) jekla za gradnjo v skladu z nacionalnimi ali regionalnimi standardi (glejte npr. DIN 1623).
OPOMBA 2: Ta evropski standard je mogoče po dogovoru v času povpraševanja in naročila uporabiti za trajno elektrolizno cinkane vroče valjane ploščate izdelke (npr. v skladu s standardi EN 10025-1 in -2, EN 10111, EN 10149-1 do EN 10149-3 itd.). OPOMBA 3: Ker je masa nanesenega cinkovega premaza sorazmerno majhna, material ni namenjen za uporabo na prostem brez dodatne kemične obdelave in barvanja.
General Information
- Status
- Withdrawn
- Publication Date
- 10-Mar-2009
- Withdrawal Date
- 20-Jan-2026
- Technical Committee
- ECISS/TC 109 - Coated and uncoated flat products to be used for cold forming
- Current Stage
- 9960 - Withdrawal effective - Withdrawal
- Start Date
- 25-Jan-2017
- Completion Date
- 28-Jan-2026
Relations
- Effective Date
- 08-Jun-2022
- Effective Date
- 23-Mar-2009
- Effective Date
- 01-Jan-2014
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
Frequently Asked Questions
EN 10152:2009 is a standard published by the European Committee for Standardization (CEN). Its full title is "Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions". This standard covers: This European Standard specifies requirements for continuously electrolytic zinc coated cold rolled flat products of low carbon steels suitable for cold forming according to Table 1 in rolled widths above or equal to 600 mm and thicknesses from 0,35 mm up to and including 3 mm, delivered as strip (in coil form), sheet, slit strip or cut lengths obtained from slit strip or sheet. NOTE 1 This European Standard can also be applied to continuously electrolytic zinc coated flat products of: a) steels according to EN 10139 (cold rolled strip in rolled widths < 600 mm), b) steels normally characterized by minimum yield strength or minimum tensile strength values in addition to formability parameters, e. g. 1) steels with high yield strength and improved formability according to EN 10268 (cold rolled flat products), 2) multiphase steels (cold rolled or hot rolled) according to prEN 10338, 3) steels for construction according to national or regional standards (see e. g. DIN 1623). NOTE 2 By agreement at the time of enquiry and order this European Standard can be applied to continuously electrolytic zinc coated hot-rolled steel flat products (e.g. according to EN 10025-1 and -2, EN 10111, EN 10149-1 to EN 10149-3, etc.). NOTE 3 As the mass of the zinc coating applied is relatively small, the material is not intended to withstand outside exposure without further chemical treatment and painting.
This European Standard specifies requirements for continuously electrolytic zinc coated cold rolled flat products of low carbon steels suitable for cold forming according to Table 1 in rolled widths above or equal to 600 mm and thicknesses from 0,35 mm up to and including 3 mm, delivered as strip (in coil form), sheet, slit strip or cut lengths obtained from slit strip or sheet. NOTE 1 This European Standard can also be applied to continuously electrolytic zinc coated flat products of: a) steels according to EN 10139 (cold rolled strip in rolled widths < 600 mm), b) steels normally characterized by minimum yield strength or minimum tensile strength values in addition to formability parameters, e. g. 1) steels with high yield strength and improved formability according to EN 10268 (cold rolled flat products), 2) multiphase steels (cold rolled or hot rolled) according to prEN 10338, 3) steels for construction according to national or regional standards (see e. g. DIN 1623). NOTE 2 By agreement at the time of enquiry and order this European Standard can be applied to continuously electrolytic zinc coated hot-rolled steel flat products (e.g. according to EN 10025-1 and -2, EN 10111, EN 10149-1 to EN 10149-3, etc.). NOTE 3 As the mass of the zinc coating applied is relatively small, the material is not intended to withstand outside exposure without further chemical treatment and painting.
EN 10152:2009 is classified under the following ICS (International Classification for Standards) categories: 77.140.50 - Flat steel products and semi-products. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 10152:2009 has the following relationships with other standards: It is inter standard links to EN 10336:2007, EN 10152:2003, EN 10152:2017, EN 10027-2:2015, EN 16603-50-53:2015, EN 10204:2004, EN 10027-1:2016, EN 10002-1:2001, EN ISO 23553-1:2014, EN 10131:2006, EN ISO 7438:2020, EN 10020:2000, EN 10079:2007, EN 10021:2006, EN ISO 14915-3:2002. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 10152:2009 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Elektrolytisch verzinkte kaltgewalzte Flacherzeugnisse aus Stahl zum Kaltumformen - Technische LieferbedingungenProduits plats en acier, laminés à froid, revêtus de zinc par voie électrolytique pour formage à froid - Conditions techniques de livraisonElectrolytically zincdip coated cold rolled steel flat products for cold forming - Technical delivery conditions77.140.50SROL]GHONLFlat steel products and semi-productsICS:Ta slovenski standard je istoveten z:EN 10152:2009SIST EN 10152:2009en,fr,de01-junij-2009SIST EN 10152:2009SLOVENSKI
STANDARDSIST EN 10336:2007SIST EN 10152:20031DGRPHãþD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10152March 2009ICS 77.140.50Supersedes EN 10152:2003, EN 10336:2007
English VersionElectrolytically zinc coated cold rolled steel flat products for coldforming - Technical delivery conditionsProduits plats en acier, laminés à froid, revêtus de zinc parvoie électrolytique pour formage à froid - Conditionstechniques de livraisonElektrolytisch verzinkte kaltgewalzte Flacherzeugnisse ausStahl zum Kaltumformen - Technische LieferbedingungenThis European Standard was approved by CEN on 31 January 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10152:2009: ESIST EN 10152:2009
Reference method for determination of the zinc coating mass . 16A.1Principle . 16A.2Reagent and preparation of the solution . 16A.2.1Reagent . 16A.2.2Preparation of the solution . 16A.3Apparatus . 16A.4Procedure . 16Bibliography . 18 SIST EN 10152:2009
EN 10079:2007, Definition of steel products EN 10131, Cold rolled uncoated and zinc or zinc-nickel electrolytically coated low carbon and high yield strength steel flat products for cold forming – Tolerances on dimensions and shape EN 10204:2004, Metallic materials – Types of inspection documents EN ISO 7438, Metallic materials – Bend test (ISO 7438:2005) ISO 10113, Metallic materials – Sheet and strip – Determination of plastic strain ratio SIST EN 10152:2009
EN 10079:2007, EN 10204:2004 and the following apply. 3.1
electrolytic zinc coating (ZE) application of a zinc coating by electrolysis on a suitably prepared steel surface from an aqueous zinc salt solution by the use of an electric current NOTE Flat products can have a zinc coating on one or both surfaces. If both surfaces are zinc coated, a different coating thickness can be applied on each side (this process being referred to as differential zinc coating). 4 Classification and designation 4.1 Classification The steel grades specified in this European Standard are classified in accordance with EN 10020:2000 as non-alloy quality steels (DC01, DC03, DC04, DC05) and alloy quality steels (DC06, DC07) and by their increasing suitability for cold forming as follows: DC01:
drawing quality; DC03:
deep drawing quality; DC04, DC05:
special deep drawing quality;
DC06: extra deep drawing quality; DC07: super deep drawing quality. 4.2 Designation 4.2.1 The steel names are allocated in accordance with EN 10027-1. The steel numbers are allocated in accordance with EN 10027-2. 4.2.2 The products covered by this document shall be designated as follows in the given order: 1) Type of product (e. g. strip, sheet, cut length); 2) Number of this European Standard (EN 10152); 3) Steel name or steel number and symbol for the type of electrolytical coating (see Table 1); 4) Numbers denoting the nominal coating thickness on each surface (e. g. 50/50 = nominal coating thickness of 5,0 µm on each side, see Table 2 and 6.9.2); 5) Letters A or B indicating the surface quality (see 6.11.2); 6) Letters denoting the surface treatment (see 6.12 and Table 3). EXAMPLE 1
Designation of strip made of steel DC03+ZE (1.0347+ZE), electrolytically zinc coated with a nominal thickness of 5,0 µm on each surface (50/50), surface quality A, surface treatment phosphated (P): SIST EN 10152:2009
Designation of sheet made of steel DC05+ZE (1.0312+ZE), electrolytically zinc coated with a nominal thickness of 7,5 µm on one surface and of 2,5 µm on the other surface (75/25), surface quality B, surface treatment phosphated and oiled (PO): Sheet EN 10152-DC05+ZE75/25-B-PO or Sheet EN 10152-1.0312+ZE75/25-B-PO 4.2.3 Where appropriate, additional information to the designation as specified in 4.2.2 shall be given to describe clearly the delivery requirements (see Clause 5). 5 Information to be supplied by the purchaser 5.1 Mandatory information The following information shall be supplied by the purchaser at the time of enquiry and order: a) complete designation (see 4.2.2); b) nominal dimensions (thickness, width and, in the case of sheet and cut lengths, length); c) quantity; d) limiting mass and sizes of the coils and individual bundles of sheets; e) surface quality and surface finish (see 6.11); f) type of surface treatment (see 6.12 and Table 3). 5.2 Options A number of options are specified in this document and listed below; if the purchaser does not indicate a wish to implement any of these options, the products shall be supplied in accordance with the basis specification of this document (see 5.1): 1) Delivery of hot rolled products (see NOTE 2 to Clause 1); 2) Use of substrates not specified in Table 1 (see 6.1); 3) Steelmaking and manufacturing processes (see 6.2); 4) Non-skin passed products (see 6.5); 5) Products supplied suitable for the manufacture of a specific part (see 6.6); 6) Delivery of several steel grades as alloy steels (see Table 1, footnote f); 7) Differential coatings (see 6.9.4); SIST EN 10152:2009
NOTE 2 Prolonged storage of products of grade DC01+ZE could result in some change in the mechanical properties leading to a reduction in formability. 6.7.2 The tensile test values apply to transverse samples and relate to the test piece cross-section without zinc coating. 6.7.3 Strain ratio r90 (see Table 1) and the strain hardening exponent n90 shall be determined in the range of homogeneous deformation, within the strain range of 10 % to 20 %.
NOTE
The uniform elongation of the material to be tested may be lower than 20 %. In this case an upper limit of the strain range of ≥ 15 % may be applied. SIST EN 10152:2009
Definition and classification according to EN 10020:2000 Deoxidation Validity of mechanical properties Surface appea-rance Absence of stretcher strain marks Re
MPa Rm
MPa A80 % min. r9
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...