EN 861:2007/prA1

SLOVENSKI STANDARD
01-april-2009
Varnost lesnoobdelovalnih strojev - Kombinirani in debelinski skobeljniki
Safety of woodworking machines - Surface planing and thicknessing machines
Sicherheit von Holzbearbeitungsmaschinen - Kombinierte Abricht- und
Dickenhobelmaschinen
Sécurité des machines pour le travail du bois - Machines combinées à raboter et à
dégauchir
Ta slovenski standard je istoveten z: EN 861:2007/prA1
ICS:
25.080.25 6WURML]DSORãþLQVNRREGHODYR Planing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
FINAL DRAFT
EN 861:2007
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
January 2009
ICS 79.120.10
English Version
Safety of woodworking machines - Surface planing and
thicknessing machines
Sécurité des machines pour le travail du bois - Machines Sicherheit von Holzbearbeitungsmaschinen - Kombinierte
combinées à raboter et à dégauchir Abricht- und Dickenhobelmaschinen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 142.
This draft amendment A1, if approved, will modify the European Standard EN 861:2007. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 861:2007/prA1:2009: E
worldwide for CEN national Members.

Contents Page
Foreword.3
1 Modification to the Foreword .4
2 Modification to Clause 2, Normative references .4
3 Modification to 5.4.5, Ergonomics and handling.4
4 Modification to 6.2, Marking .4
5 Modification to 6.3, Instruction handbook .4
6 Addition of Annex ZB .5

Foreword
This document (EN 861:2007/prA1:2009) has been prepared by Technical Committee CEN/TC 142
“Woodworking machines - Safety”, the secretariat of which is held by UNI.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of the Machinery Directive.
For relationship with EU Directive, see informative Annexes ZA and ZB, which are integral parts of this
document.
1 Modification to the Foreword
Replace the fifth paragraph with the following:
"For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.".
2 Modification to Clause 2, Normative references
Delete the reference to EN 294:1992 and add "EN ISO 13857:2008, Safety of machinery — Safety distances
to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)" and replace
"EN 294:1992" with "EN ISO 13857:2008" throughout the document.
Replace "EN ISO 13849-1:2006", "EN 13849-1:2003" and "EN ISO 13849-1:1996" with
"EN ISO 13849-1:2008" in Clause 2 and throughout the document and replace the text of footnote to text 1
with "EN ISO 13849-1:2006 superseded EN 954-1:1996.".
Replace "EN ISO 13849-2:2003" with "EN ISO 13849-2:2008" in Clause 2 and throughout the document.
3 Modification to 5.4.5, Ergonomics and handling
th
At the end of the 7 paragraph, add: "The
...