EN 14758-1:2005
(Main)Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system
Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system
This European Standard specifies the requirements for solid-wall pipes, fittings and the system of piping systems made from mineral modified polypropylene materials (PP-MD) in the field of non-pressure underground drainage and sewerage outside the building structure (application area code "U"), and non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code "D") and outside the building structure.
This is reflected in the marking of products by "U" and "UD".
It also specifies the test parameters for the test methods referred to in this European Standard.
This European Standard covers a range of nominal sizes, a range of pipe series/stiffness classes and gives recommendations concerning colours.
NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
In conjunction with Part 2 and Part 3 of EN 14758 (see Foreword) it is applicable to PP-MD pipes and fittings, their elastomeric sealing ring joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage.
This European Standard is applicable to PP-MD pipes with or without an integral socket.
NOTE 2 The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings.
NOTE 3 Requirements and limiting values for application area code "D" are given in Table 4, Table 7 and Table 13.
NOTE 4 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this European Standard, when they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 13.
Kunststoff-Rohrleitungssysteme für erdverlegte Abwasserkanäle und -leitungen - Polypropylen mit mineralischen Additiven (PP-MD) - Teil 1: Anforderungen an Rohre, Formstücke und das Rohrleitungssystem
Dieses Dokument legt für Rohrleitungssysteme aus mineralverstärktem Polypropylen (PP M) Anforderungen an Vollwandrohre, Formstücke und das Rohrleitungssystem für Abwasserkanäle und leitungen fest, die in erdverlegten Schwerkraftentwässerungssystemen
außerhalb der Gebäudestruktur (Anwendungskennzeichen "U") und
sowohl innerhalb (Anwendungskennzeichen "D") als auch außerhalb der Gebäudestruktur
eingesetzt werden.
Die Wahl des Anwendungsgebietes wird durch die Kennzeichnung der Erzeugnisse mit "U" bzw. "UD" angezeigt.
Dieser Teil legt auch die Prüfparameter für die Prüfverfahren fest, auf die in diesem Dokument verwiesen wird.
Dieses Dokument enthält eine Reihe von Nennweiten sowie Rohrreihen/Steifigkeitsklassen und gibt Empfehlungen hinsichtlich der Einfärbung.
ANMERKUNG 1 Der Anwender bzw. Auftraggeber ist unter Berücksichtigung der eigenen Anforderungen sowie der geltenden nationalen Festlegungen und Verlegepraktiken für die entsprechende Auswahl dieser Kriterien verantwortlich.
Zusammen mit Teil 2 und Teil 3 der prEN 14758 (siehe Vorwort) gilt dieser Teil für Rohre und Formstücke aus PP M, für deren Verbindungen mit elastomeren Dichtringen sowie für Verbindungen mit Rohrleitungsteilen aus anderen Kunststoffen oder Rohrwerkstoffen, die für erdverlegte drucklose Abwasserkanäle und leitungen vorgesehen sind.
Dieses Dokument ist für Rohre aus PP M sowohl mit als auch ohne angeformte Muffe anwendbar.
ANMERKUNG 2 Die Formstücke können im Spritzgießverfahren oder aus Rohren und/oder aus Spritzgussteilen hergestellt sein.
ANMERKUNG 3 Anforderungen und Grenzwerte für Anwendungsgebiete mit Anwendungskennzeichen "D" sind in Tabelle 4, Tabelle 7 und Tabelle 13 aufgeführt.
ANMERKUNG 4 Rohre, Formstücke oder andere Rohrleitungsteile, die einer der in Anhang B aufgeführten Produktnormen entsprechen, können mit Rohren und Formstücken nach diesem Dokument verwendet werden, sofern sie die Anforderungen an die Maße der Verbindungen nach Abschnitt 6 sowie die Anforderung
Systèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissement enterrés sans pression - Polypropylène avec modificateurs minéraux (PP-MD) - Partie 1: Spécifications pour les tubes, les raccords et le système
Le présent document spécifie les exigences pour les tubes, les raccords et le système de canalisations à
paroi compacte, fabriqués à partir de polypropylène avec modificateurs minéraux (PP-M) et destinés à être
utilisés pour les branchements et les collecteurs d�assainissement enterrés sans pression à l�extérieur de la
structure du bâtiment (code de zone d�application « U »), et pour les branchements et les collecteurs
d�assainissement enterrés sans pression aussi bien à l�intérieur de la structure du bâtiment (code de zone
d�application « D ») qu�à l�extérieur de celle-ci.
Ces informations sont précisées dans le marquage des produits par les lettres « U » et « UD ».
Le présent document spécifie également les paramètres d�essai pour les méthodes d�essai référencées dans
ce document.
Il couvre une gamme de dimensions nominales, une gamme de séries de tubes/classes de rigidité et donne
des recommandations concernant les couleurs.
NOTE 1 Il est de la responsabilité de l�acheteur ou du prescripteur d�effectuer les choix appropriés à partir de ces
données, en tenant compte des exigences particulières et de toute réglementation nationale applicable ainsi que des
pratiques ou codes de pose.
En relation avec la Partie 2 et la Partie 3 du prEN 14758 (voir l�Avant-propos), ce document s�applique aux
tubes et aux raccords en PP-M, à leurs assemblages à bague d�étanchéité en élastomère et aux
assemblages avec des composants en matières plastiques et non plastiques différentes destinés à être
utilisés dans les systèmes de canalisations enterrés pour les branchements et l�assainissement sans pression.
Le présent document est applicable aux tubes PP-M avec et sans emboîtures.
NOTE 2 Les raccords peuvent être fabriqués par moulage par injection ou être façonnés à partir de tubes et/ou de
pièces moulées.
Cevni sistemi iz polimernih materialov za odvodnjavanje in kanalizacijo, ki delujejo po težnostnem principu - Polipropilen z mineralnimi modifikatorji (PP-MD) – 1. del: Specifikacije za cevi, fitinge in cevni sistem
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2006
Cevni sistemi iz polimernih materialov za odvodnjavanje in kanalizacijo, ki delujejo
po težnostnem principu - Polipropilen z mineralnimi modifikatorji (PP-MD) – 1. del:
Specifikacije za cevi, fitinge in cevni sistem
Plastics piping systems for non-pressure underground drainage and sewerage -
Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings
and the system
Kunststoff-Rohrleitungssysteme für erdverlegte Abwasserkanäle und -leitungen -
Polypropylen mit mineralischen Additiven (PP-MD) - Teil 1: Anforderungen an Rohre,
Formstücke und das Rohrleitungssystem
Systemes de canalisations en plastique pour les branchements et les collecteurs
d'assainissement enterrés sans pression - Polypropylene avec modificateurs minéraux
(PP-MD) - Partie 1: Spécifications pour les tubes, les raccords et le systeme
Ta slovenski standard je istoveten z: EN 14758-1:2005
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 14758-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2005
ICS 93.030
English Version
Plastics piping systems for non-pressure underground drainage
and sewerage - Polypropylene with mineral modifiers (PP-MD) -
Part 1: Specifications for pipes, fittings and the system
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für erdverlegte
branchements et les collecteurs d'assainissement enterrés Abwasserkanäle und -leitungen - Polypropylen mit
sans pression - Polypropylène avec modificateurs minéraux mineralischen Additiven (PP-MD) - Teil 1: Anforderungen
(PP-MD) - Partie 1: Spécifications pour les tubes, les an Rohre, Formstücke und das Rohrleitungssystem
raccords et le système
This European Standard was approved by CEN on 24 November 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14758-1:2005: E
worldwide for CEN national Members.
Contents Page
Foreword .4
1 Scope .5
2 Normative references.5
3 Terms, definitions, symbols and abbreviations.6
3.1 Terms and definitions.6
3.2 Symbols .9
3.3 Abbreviations .9
4 Material .10
4.1 PP-MD material.10
4.2 Reprocessable and recyclable material.10
4.3 Melt mass-flow rate .10
4.4 Mineral modifiers.10
4.5 Durability .11
4.6 Sealing ring retaining means.13
5 General characteristics.13
5.1 Appearance.13
5.2 Colour .13
6 Geometrical characteristics .13
6.1 General .13
6.2 Dimensions of pipes.13
6.3 Ring stiffness classes.17
6.4 Dimensions of fittings .17
6.5 Dimensions of sockets and spigots .18
6.6 Types of fittings.22
7 Mechanical characteristics of pipes .24
7.1 Mechanical characteristics of pipes.24
7.2 Mechanical characteristics of fittings .26
8 Physical characteristics .27
8.1 Physical characteristics of pipes.27
8.2 Physical characteristics of fittings.27
9 Performance requirements.28
10 Sealing rings.29
11 Marking .29
11.1 General .29
11.2 Minimum required marking of pipes .29
11.3 Minimum required marking of fittings.30
11.4 Additional marking.31
Annex A (informative) General characteristics of PP-MD pipes and fittings .32
A.1 General.32
A.2 Material characteristics .32
A.3 Ring stiffness .32
A.4 Chemical resistance.33
A.5 Abrasion resistance.33
A.6 Hydraulic roughness.33
A.7 Diametric deflection.33
Annex B (informative) Standards for pipes and fittings of a material other than PP-MD.34
Bibliography.35
Foreword
This European Standard (EN 14758-1:2005) has been prepared by Technical Committee CEN/TC 155
“Plastics piping systems and ducting systems”, the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2006, and conflicting national standards shall be withdrawn at
the latest by June 2006.
This European Standard is a part of a system standard for plastics piping systems of a particular material for a
specified application. There are a number of such system standards.
They are supported by separate standards on test methods to which references are made throughout the
system standard.
The system standards are consistent with general standards on functional requirements and on recommended
practice for installation.
EN 14758 consists of the following parts under the general title Plastics piping systems for non-pressure
underground drainage and sewerage — Polypropylene with mineral modifiers (PP-MD)
Part 1: Specifications for pipes, fittings and the system (this document)
Part 2: Guidance for the assessment of conformity (intended to be published as CEN/Technical Specification)
Part 3: Guidance for installation (intended to be published as CEN/Technical Specification).
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland
and United Kingdom.
1 Scope
This European Standard specifies the requirements for solid-wall pipes, fittings and the system of piping
systems made from mineral modified polypropylene materials (PP-MD) in the field of non-pressure
underground drainage and sewerage outside the building structure (application area code "U"), and non-
pressure underground drainage and sewerage for both buried in ground within the building structure
(application area code "D") and outside the building structure.
This is reflected in the marking of products by "U" and "UD".
It also specifies the test parameters for the test methods referred to in this European Standard.
This European Standard covers a range of nominal sizes, a range of pipe series/stiffness classes and gives
recommendations concerning colours.
NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects,
taking into account their particular requirements and any relevant national regulations and installation practices or codes.
In conjunction with Part 2 and Part 3 of EN 14758 (see Foreword) it is applicable to PP-MD pipes and fittings,
their elastomeric sealing ring joints and to joints with components of other plastics and non-plastics materials
intended to be used for buried piping systems for non-pressure underground drainage and sewerage.
This European Standard is applicable to PP-MD pipes with or without an integral socket.
NOTE 2 The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings.
NOTE 3 Requirements and limiting values for application area code "D" are given in Table 4, Table 7 and Table 13.
NOTE 4 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can
be used with pipes and fittings conforming to this European Standard, when they conform to the requirements for joint
dimensions given in Clause 6 and to the requirements of Table 13.
2 Normative references
The following referenced documents are indispensable for the application of this European Standard. For
dated references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 681-1, Elastomeric seals — Material requirements for pipe joint seals used in water and drainage
applications — Part 1: Vulcanized rubber
EN 681-2, Elastomeric seals — Material requirements for pipe joint seals used in water and drainage
applications — Part 2: Thermoplastic elastomers
EN 744:1995, Plastics piping and ducting systems — Thermoplastics pipes — Test method for resistance to
external blows by the round-the-clock method
EN 921:1994,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.