EN 13369:2018
(Main)Common rules for precast concrete products
Common rules for precast concrete products
This document specifies the requirements, the basic performance criteria and the Assessment and Verification of Constancy of Performance (AVCP) for unreinforced, reinforced and prestressed precast concrete products made of compact light-, normal- and heavyweight concrete according to EN 206 with no appreciable amount of entrapped air other than entrained air. Concrete containing fibres for other than mechanical properties (steel, polymer or other fibres) is also covered. It does not cover prefabricated reinforced components of lightweight aggregate concrete with open structure.
It may also be used to specify products for which there is no standard. Not all of the requirements (Clause 4) of this standard are relevant to all precast concrete products.
If a specific product standard exists, it takes precedence over this document.
The precast concrete products dealt with in this standard are factory produced for building and civil engineering works. This document can also be applied to products manufactured in temporary plants on site if the production is protected against adverse weather conditions and controlled following Clause 6 provisions.
The analysis and design of precast concrete products is not within the scope of this document but it does offer, for non-seismic zones, information about:
- the choice of partial safety factors defined by the pertinent Eurocode;
- the definition of some requirements for prestressed concrete products.
Allgemeine Regeln für Betonfertigteile
Diese Europäische Norm legt die Anforderungen, die grundlegenden Eigenschaften und die Kon-formitätsbewertung für Beton-, Stahlbeton- und Spannbetonfertigteile aus Leicht-, Normal und Schwerbeton nach EN 206 fest, der so verdichtet wurde, dass er außer den Luftporen keine nennenswerten Lufteinschlüsse enthält. Faserbetone, deren Fasern keinen Einfluss auf die mechanischen Eigenschaften haben, wie Stahl-, Polymer- oder andere Fasern, sind ebenfalls enthalten. Sie gilt nicht für Betonfertigteile aus haufwerksporigem Leichtbeton.
Diese Norm kann auch für spezielle Fertigteile verwendet werden, für die keine Produktnormen existieren. Nicht alle Anforderungen (Abschnitt 4) dieser Norm sind für alle Betonfertigteile maßgebend.
Wenn eine spezielle Produktnorm vorliegt, hat sie Vorrang gegenüber dieser Norm.
Die in der vorliegenden Norm behandelten Fertigteile sind werkmäßig hergestellte Bauteile für den Hoch- und Ingenieurbau. Diese Norm kann auch für Fertigteile angewendet werden, die in temporären Anlagen auf der Baustelle hergestellt werden, wenn die Herstellung vor ungünstigen Witterungseinflüssen geschützt ist und nach den Festlegungen in Abschnitt 6 kontrolliert wird.
Die Berechnung und Bemessung von Betonfertigteilen gehören nicht zum Anwendungsbereich dieser Norm, sie enthält jedoch für Nicht-Erdbebengebiete Angaben zur:
- Auswahl der Teilsicherheitsbeiwerte, die durch den Eurocode festgelegt sind;
- Festlegung einiger Anforderungen an Spannbetonfertigteile.
Règles communes pour les produits préfabriqués en béton
La présente Norme européenne spécifie les prescriptions, les critères relatifs aux performances de base et l’Evaluation et la Vérification de la Constance des Performances (EVCP) des produits préfabriqués non armés, armés et précontraints en béton léger, normal et lourd conformément à l’EN 206, sans quantité notable d’air occlus autre que l’air entraîné. Elle couvre également le béton contenant des fibres (acier, polymère ou autre) pour d’autres propriétés que les propriétés mécaniques. Elle ne couvre pas les produits préfabriqués armés en béton de granulats légers à structure ouverte.
Elle peut aussi être utilisée pour spécifier des produits pour lesquels il n’existe pas de norme. Les prescriptions (Article 4) de la norme ne sont pas toutes applicables à l’ensemble des produits préfabriqués en béton.
Si une norme de produit spécifique existe, elle a priorité sur la présente norme.
Les produits préfabriqués en béton considérés dans la présente norme sont fabriqués en usine et destinés à des bâtiments ou des ouvrages de génie civil. La présente norme peut également être appliquée à des éléments fabriqués dans des installations provisoires sur chantier, à condition que la fabrication soit protégée contre les conditions environnementales néfastes et soit contrôlée selon les prescriptions de l’Article 6.
L’analyse et le calcul de produits préfabriqués en béton ne sont pas inclus dans cette norme mais elle donne, pour les zones non sismiques, des informations sur :
- le choix de coefficients de sécurité partiels définis par l’Eurocode correspondant ;
- la définition de quelques prescriptions pour les produits en béton précontraint.
Splošna pravila za montažne betonske izdelke
Ta evropski standard določa zahteve, osnovna merila učinkovitosti in vrednotenje skladnosti za montažne izdelke iz nearmiranega, armiranega in prednapetega kompaktnega betona, ki je lahek, normalen ali težek, v skladu s standardom EN 206 brez znatne količine ujetega zraka, razen primešanega zraka. Standard zajema tudi beton, ki vsebuje vlakna zaradi drugih razlogov, kot so mehanske lastnosti, jeklo, polimer ali druga vlakna. Standard ne zajema montažnih armiranih komponent iz lahkega betona za agregate z odprto konstrukcijo.
Uporablja se lahko tudi za določanje izdelkov, za katere standard ne obstaja. Vse zahteve (točka 4) tega standarda ne veljajo za vse montažne betonske izdelke.
Če obstaja poseben standard za izdelek, ima prednost pred tem standardom.
Montažni betonski izdelki, obravnavani v tem standardu, so tovarniško proizvedeni za stavbe in gradbene inženirske objekte. Ta standard se lahko uporablja tudi za izdelke, proizvedene v začasnih obratih na delovišču, če je proizvodnja zaščitena pred negativnimi vremenskimi pogoji in nadzorovana v skladu z določbami iz točke 6.
Analiza in načrtovanje montažnih betonskih izdelkov nista predmet tega standarda, vendar za območja, ki niso potresna, nudi informacije o:
– izbiri delnih varnostnih dejavnikov, ki jih določa zadevni evrokod;
– opredelitvi nekaterih zahtev za prednapete betonske izdelke.
General Information
- Status
- Withdrawn
- Publication Date
- 10-Apr-2018
- Withdrawal Date
- 13-Apr-2025
- Technical Committee
- CEN/TC 229 - Precast concrete products
- Current Stage
- 9960 - Withdrawal effective - Withdrawal
- Start Date
- 15-Nov-2023
- Completion Date
- 14-Apr-2025
Relations
- Effective Date
- 30-Sep-2016
- Effective Date
- 19-Jan-2023
Frequently Asked Questions
EN 13369:2018 is a standard published by the European Committee for Standardization (CEN). Its full title is "Common rules for precast concrete products". This standard covers: This document specifies the requirements, the basic performance criteria and the Assessment and Verification of Constancy of Performance (AVCP) for unreinforced, reinforced and prestressed precast concrete products made of compact light-, normal- and heavyweight concrete according to EN 206 with no appreciable amount of entrapped air other than entrained air. Concrete containing fibres for other than mechanical properties (steel, polymer or other fibres) is also covered. It does not cover prefabricated reinforced components of lightweight aggregate concrete with open structure. It may also be used to specify products for which there is no standard. Not all of the requirements (Clause 4) of this standard are relevant to all precast concrete products. If a specific product standard exists, it takes precedence over this document. The precast concrete products dealt with in this standard are factory produced for building and civil engineering works. This document can also be applied to products manufactured in temporary plants on site if the production is protected against adverse weather conditions and controlled following Clause 6 provisions. The analysis and design of precast concrete products is not within the scope of this document but it does offer, for non-seismic zones, information about: - the choice of partial safety factors defined by the pertinent Eurocode; - the definition of some requirements for prestressed concrete products.
This document specifies the requirements, the basic performance criteria and the Assessment and Verification of Constancy of Performance (AVCP) for unreinforced, reinforced and prestressed precast concrete products made of compact light-, normal- and heavyweight concrete according to EN 206 with no appreciable amount of entrapped air other than entrained air. Concrete containing fibres for other than mechanical properties (steel, polymer or other fibres) is also covered. It does not cover prefabricated reinforced components of lightweight aggregate concrete with open structure. It may also be used to specify products for which there is no standard. Not all of the requirements (Clause 4) of this standard are relevant to all precast concrete products. If a specific product standard exists, it takes precedence over this document. The precast concrete products dealt with in this standard are factory produced for building and civil engineering works. This document can also be applied to products manufactured in temporary plants on site if the production is protected against adverse weather conditions and controlled following Clause 6 provisions. The analysis and design of precast concrete products is not within the scope of this document but it does offer, for non-seismic zones, information about: - the choice of partial safety factors defined by the pertinent Eurocode; - the definition of some requirements for prestressed concrete products.
EN 13369:2018 is classified under the following ICS (International Classification for Standards) categories: 91.100.30 - Concrete and concrete products. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 13369:2018 has the following relationships with other standards: It is inter standard links to EN 13369:2013, EN 13369:2023. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 13369:2018 is associated with the following European legislation: EU Directives/Regulations: 305/2011; Standardization Mandates: M/100. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
You can purchase EN 13369:2018 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of CEN standards.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Splošna pravila za montažne betonske izdelkeAllgemeine Regeln für BetonfertigteileRègles communes pour les produits préfabriqués en bétonCommon rules for precast concrete products91.100.30Beton in betonski izdelkiConcrete and concrete productsICS:Ta slovenski standard je istoveten z:EN 13369:2018SIST EN 13369:2018en,fr,de01-maj-2018SIST EN 13369:2018SLOVENSKI
STANDARDSIST EN 13369:20131DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13369
April
t r s z ICS
{ sä s r rä u r Supersedes EN
s u u x {ã t r s uEnglish Version
Common rules for precast concrete products Règles communes pour les produits préfabriqués en béton
Allgemeine Regeln für Betonfertigteile This European Standard was approved by CEN on
s r January
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s u u x {ã t r s z ESIST EN 13369:2018
Concrete cover as regard to corrosion . 35 A.1 Minimum concrete cover for base conditions . 35 A.2 Alternative conditions . 36 Annex B (informative)
Concrete quality control . 37 B.1 Statistical representative values . 37 B.2 Conformity criteria for potential strength . 37 B.3 Direct structural strength . 37 B.4 Indirect structural strength . 37 B.5 Direct assessment of possibly non-conforming units . 38 Annex C (informative)
Reliability considerations . 40 C.1 General . 40 C.2 Reduction based on quality control and reduced tolerances . 40 C.3 Reduction based on using reduced or measured geometrical parameters in design . 40 C.4 Reduction based on assessment of concrete strength in finished structure . 41 C.5 G based on control of self-weight . 41 Annex D (normative)
Inspection schemes . 42 D.1 General . 42 D.2 Equipment inspection . 42 D.3 Materials inspection . 44 D.4 Process inspection . 46 D.5 Finished product inspection . 49 D.6 Switching rules . 49 Annex E (informative)
Assessment of compliance . 51 E.1 General . 51 E.1.1 General remark . 51 E.1.2 Compliance of factory quality system . 51 E.1.3 Compliance of the product . 51 SIST EN 13369:2018
Test of water absorption . 53 F.1 Method . 53 F.2 Sampling . 53 F.3 Materials . 56 F.4 Apparatus . 56 F.5 Preparation . 56 F.6 Procedure. 56 F.7 Results . 57 Annex G (informative)
Shape correlation factor for cores . 58 Annex H (informative)
Measurement of dimensions . 59 H.1 Length, height, width and thickness . 59 H.2 Warp and straightness . 60 H.3 Out of squareness . 60 H.4 Surface characteristics . 60 H.5 Angular deviation lateral bow, camber and sag. 64 Annex I (informative)
Prestressing losses . 65 I.1 General . 65 I.2 Calculation of losses (general method) . 65 I.2.1 Losses before transfer of the prestress force . 65 I.2.2 Loss at transfer of the prestress force . 66 I.2.3 Losses after transfer of the prestressing force . 66 I.2.4 Final prestress loss at infinite time . 66 I.3 Simplified method . 66 Annex J (informative)
Technical documentation . 68 J.1 General . 68 J.2 Product documentation . 68 J.3 Production documentation. 68 J.4 Erection documentation . 69 Annex K (informative)
Properties of indented bars and wire . 70 Annex L (informative)
Resistance to fire: recommendations for the use of EN 1992-1-2 . 71 L.1 Use of tabulated data . 71 L.2 Use of calculation methods . 71 Annex M (informative)
Survey of type testing . 72 SIST EN 13369:2018
Use of reclaimed crushed and recycled coarse aggregates in concrete . 74 N.1 General . 74 N.2 Reclaimed crushed aggregates . 74 N.3 Recycled coarse aggregates (aggregates from external source) assessed by the manufacturer . 74 N.4 Other recycled coarse aggregates . 74 Bibliography . 75
1 As impacted by EN 1992-1-1:2004/AC:2010 and EN 1992-1-1:2004/A1:2014. 2 As impacted by EN 1992-1-2:2004/AC:2008. SIST EN 13369:2018
— ISO Online browsing platform: available at http://www.iso.org/obp
[SOURCE: EN 1992-1-1:2004] 3.1.3 concrete family group of concrete compositions for which a reliable relationship between relevant properties is established and documented
[SOURCE: EN 206:2013+A1:2016] 3.1.4 tendon prestressing unit (wire, strand or bar) subjected to pre- or post-tensioning 3.1.5 lightweight concrete concrete with a closed structure and with an oven-dry density of 800 kg/m3 to 2 000 kg/m3 3.1.6 normal weight concrete concrete with an oven-dry density of 2 000 kg/m3 to 2 600 kg/m3 3.1.7 heavyweight concrete concrete with an oven-dry density of more than 2 600 kg/m3 3.1.8 product-type set of representative performance levels or classes of construction product, in relation to its characteristics, produced using a given combination of raw materials or other elements in a specific production process 3.2 Dimensions 3.2.1 principal dimensions length, width, depth or thickness SIST EN 13369:2018
% Cylinder/cube fc,L
MPa X0, XC1 only requirements on fc,L apply. 12/15 XC2, XC3, XC4, XD1, XD2, XF1 35 12/15 a All other exposure conditions (wetting/drying cycles) 50 16/20 b a This value has to be substituted by 0,25.fck if 0,25.fck
· 12 MPa (cylinder); 15 MPa (cube). b This value has to be substituted by 0,35.fck if 0,35.fck
· 16 MPa (cylinder); 20 MPa (cube). Other means than those defined in Table 1 may be employed if the value of the water absorption of the concrete, measured according to the test procedure defined in Annex F, does not exceed 10 % (in relative proportion) of the value of water absorption of the concrete complying with the requirements in Table 2. SIST EN 13369:2018
¶ 85 °C b Wet and cyclic wet — Tmean
¶ 65 °C a Individual values may be 5 °C higher. b When 70 °C < Tmean
¶ 85 °C initial tests shall have demonstrated that the structural strength at 90 d corresponds with normal evolution of hardening with respect to the structural strength obtained at 28 days. For wet and cyclic wet environments, in case of no long term positive experience, the suitability of the higher temperature treatment shall be demonstrated; the following limits may be a basis for this demonstration: for concrete: Na2Oeq content
¶ 3,5 kg/m3, for cement SO3 content
¶ 3,5 % by mass. The above limits for Na2Oeq and SO3 content may be changed in value, or limits on other constituents may be put, according to the res
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...