EN 17106-3-2:2021

SLOVENSKI STANDARD
01-december-2021
Nadomešča:
SIST EN 13019:2002+A1:2009
SIST EN 13021:2004+A1:2009
SIST EN 13524:2004+A2:2014
Obratovanje cestnih strojev - Varnost - 3-2. del: Stroji za storitve zimske službe -
Posebne zahteve za posipalnike
Road operation machinery - Safety - Part 3-2: Winter service machines - Specific
requirements for spreading machines
Maschinen für den Straßenbetriebsdienst - Sicherheit - Teil 3-2: Maschinen für den
Winterdienst - Spezifische Anforderungen für Streumaschinen
Machines d’exploitation des routes - Sécurité - Partie 3-2 : Machines de service hivernal
- Prescriptions spécifiques pour les machines d’épandage
Ta slovenski standard je istoveten z: EN 17106-3-2:2021
ICS:
43.160 Vozila za posebne namene Special purpose vehicles
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 17106-3-2
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2021
EUROPÄISCHE NORM
ICS 43.160; C Supersedes EN 13019:2001+A1:2008, EN
13021:2003+A1:2008, EN 13524:2003+A2:2014
English Version
Road operation machinery - Safety - Part 3-2: Winter
service machines - Specific requirements for spreading
machines
Machines d'exploitation des routes - Sécurité - Partie 3- Maschinen für den Straßenbetriebsdienst - Sicherheit -
2 : Machines de service hivernal - Prescriptions Teil 3-2: Maschinen für den Winterdienst - Spezifische
spécifiques pour les machines d'épandage Anforderungen für Streumaschinen
This European Standard was approved by CEN on 16 August 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 17106-3-2:2021 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Safety requirements and/or protective/risk reduction measures . 6
4.1 General . 6
4.2 Noise . 6
4.3 Controls . 6
4.4 Guards . 7
4.5 Operator stations . 9
4.6 Electrical and electronic systems . 9
4.7 Provisions for lifting and lashing of machine parts or the whole machine. 9
4.8 Maintenance . 10
5 Verification of the safety requirements and/or protective/risk reduction measures . 10
6 Information for use . 12
Annex A (informative) List of significant hazards . 13
Annex B (informative) Terminology . 18
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive2006/42/EC aimed to be covered . 20
European foreword
This document (EN 17106-3-2:2021) has been prepared by Technical Committee CEN/TC 151
“Construction equipment and building material machines - Safety”, the secretariat of which is held by
DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2022, and conflicting national standards shall be
withdrawn at the latest by April 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13019:2001+A1:2008, EN 13021:2003+A1:2008,
EN 13524:2003+A2:2014.
This document has been prepared under a standardization request given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of
EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
EN 17106:2021 consists of the following parts under the general title “Road operation machinery –
Safety”:
— Part 1: General requirements
— Part 2: Specific requirements for road surface cleaning machines
— Part 3-1: Winter service machines - Specific requirements for snow clearing machines with rotating
tools and snow ploughs
— Part 3-2: Winter service machines - Specific requirements for spreading machines
— Part 4: Road service area maintenance machines - Specific requirements for grass and brush cutting
machines
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
Introduction
This document is a type-C standard as stated in EN ISO 12100:2010.
This document is of relevance, in particular, for the following stakeholder groups representing the market
players with regard to machinery safety:
— machine manufacturers (small, medium and large enterprises);
— health and safety bodies (regulators, accident prevention organizations, market surveillance etc.).
Others can be affected by the level of machinery safety achieved with the means of the document by the
above-mentioned stakeholder groups:
— machine users/employers (small, medium and large enterprises);
— machine users/employees (e.g. trade unions, organizations for people with special needs);
— service providers, e.g. for maintenance (small, medium and large enterprises);
— consumers (in case of machinery intended for use by consumers).
The above-mentioned stakeholder groups have been given the possibility to participate at the drafting
process of this document.
The machinery concerned and the extent to which hazards, hazardous situations or hazardous events are
covered are indicated in the scope of this document.
When requirements of this type-C standard are different from those which are stated in type-A or type-B
standards, the requirements of this type-C standard take precedence over the requirements of the other
standards for machines that have been designed and built according to the requirements of this type-C
standard.
1 Scope
This document together with EN 17106-1:2021 deals with all significant hazards, hazardous situations
and events relevant to winter service machines – spreading machines when used as intended and under
the conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A) associated
with the whole lifetime of the machine as described in EN ISO 12100:2010, 5.4.
The requirements of this document are complementary to the common requirements formulated in
EN 17106-1:2021. This document does not repeat the requirements from EN 17106-1:2021 but
supplements or modifies the requirements for winter service machines – spreading machines.
This document is not applicable to spreading machines manufactured before the date of its publication.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 12195-1:2010, Load restraining on road vehicles - Safety - Part 1: Calculation of securing forces
EN 15144:2007, Winter maintenance equipment - Terminology - Terms for winter maintenance
EN 17106-1:2021, Road operation machinery — Safety — Part 1: General requirements
EN ISO 6682:2008, Earth-moving machinery - Zones of comfort and reach for controls (ISO 6682:1986,
including Amd 1:1989)
EN ISO 12100:2010, Safety of machinery - General principles for design - Risk assessment and risk reduction
(ISO 12100:2010)
EN ISO 13850:2015, Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015)
EN ISO 13857:2019, Safety of machinery — Safety distances to prevent hazard zones being reached by
upper and lower limbs (ISO 13857:2019)
EN ISO 14119:2013, Safety of machinery - Interlocking devices associated with guards - Principles for
design and selection (ISO 14119:2013)
ISO 15818:2017, Earth-moving machinery — Lifting and tying-down attachment points — Performance
requirements
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 15144:2007, EN 17106-1:2021
and EN ISO 12100:2010 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org/
3.1
operating area
section of surface covered with spreading material while machine is stationary, according to all possible
spreading widths and other settings
4 Safety requirements and/or protective/risk reduction measures
4.1 General
Winter service machines – spreading machines shall comply with the safety requirements and/or
protective/risk reduction measures of this clause. In addition, the machines shall be designed according
to the principles of EN ISO 12100:2010 for relevant but not significant hazards which are not dealt with
by this document.
Winter service machines – spreading machines shall comply with the requirements of EN 17106-1:2021,
as far as not modified or replaced by the requirements of this part.
4.2 Noise
4.2.1 Noise reduction by protective measures
EN 17106-1:2021, 4.1.2.1.2 applies with the following modifications:
A cab is not considered as a suitable measure to reduce the noise level.
4.2.2 Noise measurement - Operating conditions
EN 17106-1:2021, Annex B applies with the following addition:
Spreaders shall be tested in a stationary position. The spreader shall, according to the manufacturer’s
recommendations, operate with the working equipment at its maximum speed and the engine at the
corresponding speed.
The period of observation shall at least be 15 s.
4.3 Controls
4.3.1 General
EN 17106-1:2021, 4.1.4.1 applies with the following addition:
Controls for adjusting the amount and width of spreading shall be positioned outside the operating area.
This requirement is considered to be satisfied when spreading machines are controlled by remote control
from the cab of the carrier vehicle.
Operation modes shall be activated by a lockable mode selector.
The activation of the selected operation mode shall be optically indicated at the operator's station(s).
...