EN ISO 13165-2:2020

SLOVENSKI STANDARD
01-maj-2020
Kakovost vode - Radij Ra-226 - 2. del: Preskusna metoda z emanometrijo (ISO
13165-2:2014)
Water quality - Radium-226 - Part 2: Test method using emanometry (ISO 13165-
2:2014)
Wasserbeschaffenheit - Radium 226 - Teil 2: Untersuchungsverfahren mittels
Emanometrie (ISO 13165-2:2014)
Qualité de l'eau - Radium 226 - Partie 2: Méthode d'essai par émanométrie (ISO 13165-
2:2014)
Ta slovenski standard je istoveten z: EN ISO 13165-2:2020
ICS:
13.060.60 Preiskava fizikalnih lastnosti Examination of physical
vode properties of water
17.240 Merjenje sevanja Radiation measurements
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 13165-2
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2020
EUROPÄISCHE NORM
ICS 13.060.60; 17.240
English Version
Water quality - Radium-226 - Part 2: Test method using
emanometry (ISO 13165-2:2014)
Qualité de l'eau - Radium 226 - Partie 2: Méthode Wasserbeschaffenheit - Radium 226 - Teil 2:
d'essai par émanométrie (ISO 13165-2:2014) Untersuchungsverfahren mittels Emanometrie (ISO
13165-2:2014)
This European Standard was approved by CEN on 6 October 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13165-2:2020 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
The text of ISO 13165-2:2014 has been prepared by Technical Committee ISO/TC 147 "Water quality”
of the International Organization for Standardization (ISO) and has been taken over as EN ISO 13165-
2:2020 by Technical Committee CEN/TC 230 “Water analysis” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2020, and conflicting national standards shall
be withdrawn at the latest by August 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 13165-2:2014 has been approved by CEN as EN ISO 13165-2:2020 without any
modification.
INTERNATIONAL ISO
STANDARD 13165-2
First edition
2014-04-15
Water quality — Radium-226 —
Part 2:
Test method using emanometry
Qualité de l’eau — Radium 226 —
Partie 2: Méthode d’essai par émanométrie
Reference number
ISO 13165-2:2014(E)
©
ISO 2014
ISO 13165-2:2014(E)
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved

ISO 13165-2:2014(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms, definitions and symbols . 1
3.1 Terms and definitions . 1
3.2 Symbols . 2
4 Principle . 2
5 Reagents and equipment . 3
5.1 Reagents. 3
5.2 Equipment . 3
6 Sampling and storage . 4
6.1 Sampling . 4
6.2 Sample storage . 4
7 Procedures . 4
7.1 Sample preparation . 4
7.2 Measurement conditions . . 5
7.3 Counting procedure . 5
8 Quality assurance and quality control programme . 5
8.1 General . 5
8.2 Influence parameters . 5
8.3 Instrument verification and calibration . 6
8.4 Method verification . 6
8.5 Demonstration of analyst capability . 6
9 Expression of results . 6
9.1 Activity concentration of water-soluble Ra . 6
9.2 Standard uncertainty of activity concentration . 7
9.3 Limits of the confidence interval . 8
9.4 Example . 8
10 Test report . 8
Annex A (informative) Decay chains of uranium-238 and thorium-232.10
Annex B (informative) Bubbler .12
Annex C (informative) Glass scintillation cell .14
Bibliography .15
ISO 13165-2:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 147, Water quality, Subcommittee SC 3,
Radioactivity measurements.
ISO 13165 consists of the following parts, under the general t
...