EN 1762:2018
(Main)Rubber hoses and hose assemblies for liquefied petroleum gas, LPG (liquid or gaseous phase), and natural gas up to 25 bar (2,5 MPa) - Specification
Rubber hoses and hose assemblies for liquefied petroleum gas, LPG (liquid or gaseous phase), and natural gas up to 25 bar (2,5 MPa) - Specification
This European Standard specifies the requirements for rubber hoses and rubber hose assemblies used for the transfer of liquefied petroleum gas (LPG) in liquid or gaseous phase and natural gas with a maximum working pressure of 25 bar (2,5 MPa) and vacuum within the temperature range of −30 °C to +70 °C and, when designated -LT, −50 °C to +70 °C.
Gummischläuche und -schlauchleitungen für Flüssiggas LPG (flüssig oder gasförmig) und Erdgas bis 25 bar (2,5 MPa) - Spezifikation
Diese Europäische Norm legt die Anforderungen für Gummischläuche und Gummischlauchleitungen fest, die für den Transport von Flüssiggas (LPG) in der flüssigen oder gasförmigen Phase verwendet werden sowie für Erdgas mit einem maximalen Betriebsdruck von 25 bar (2,5 MPa) und einem Vakuum in einem Temperaturbereich von -30 °C bis +70 °C und, -50 °C bis +70 °C, wenn es mit -LT bezeichnet wird.
Tuyaux et flexibles en caoutchouc pour le gaz de pétrole liquéfié GPL (en phase liquide ou gazeuse) et le gaz naturel jusqu'à 25 bar (2,5 MPa) -Spécification
La présente Norme européenne spécifie les exigences relatives aux tuyaux et flexibles en caoutchouc destinés au transfert de gaz de pétrole liquéfié (GPL) en phase liquide ou gazeuse et de gaz naturel avec une pression maximale de service de 25 bar (2,5 MPa) et sous vide dans la plage de température de −30 °C à +70 °C, et pour le type LT de −50 °C à +70 °C.
Gumene cevi in cevni priključki za utekočinjeni naftni plin, LPG (tekoča ali plinska faza) in zemeljski plin do 25 barov (2,5 MPa) - Specifikacija
Ta evropski standard določa zahteve za gumene cevi in njihove priključke za prenos utekočinjenega naftnega plina (LPG) v tekočem ali plinskem stanju in zemeljskega plina z največjo vrednostjo delovnega tlaka 25 barov (2,5 MPa) ter vakuumom v temperaturnem območju od –30 ºC do 70 ºC in (kadar je določeno) –LT, od –50 ºC do 70 ºC.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Gummischläuche und -schlauchleitungen für Flüssiggas LPG (flüssig oder gasförmig) und Erdgas bis 25 bar (2,5 MPa) - SpezifikationTuyaux et flexibles en caoutchouc pour le gaz de pétrole liquéfié GPL (en phase liquide ou gazeuse) et le gaz naturel jusqu'à 25 bar (2,5 MPa) -SpécificationRubber hoses and hose assemblies for liquefied petroleum gas, LPG (liquid or gaseous phase), and natural gas up to 25 bar (2,5 MPa) - Specification83.140.40Gumene ceviHoses75.200Petroleum products and natural gas handling equipmentICS:Ta slovenski standard je istoveten z:EN 1762:2018SIST EN 1762:2019en,fr,de01-marec-2019SIST EN 1762:2019SLOVENSKI
STANDARDSIST EN 1762:20171DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1762
December
t r s z ICS
t uä r v rä y r Supersedes EN
s y x tã t r s yEnglish Version
Rubber hoses and hose assemblies for liquefied petroleum Tuyaux et flexibles en caoutchouc pour le gaz de
Gummischläuche und æschlauchleitungen für Flüssiggas This European Standard was approved by CEN on
{ November
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s y x tã t r s z ESIST EN 1762:2019
Flammability test . 14 A.1 Method . 14 A.2 Assessment . 14 Annex B (normative)
Test frequency for type tests and routine tests . 16 Annex C (informative)
Test frequency for production acceptance tests . 18 Annex D (informative)
Environmental checklist . 20 Bibliography . 22 SIST EN 1762:2019
« u r °C to +70 °C and, when designated -LTá
« w r °C to +70 °C. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing (ISO 1402) EN ISO 4671, Rubber and plastics hoses and hose assemblies — Methods of measurement of the dimensions of hoses and the lengths of hose assemblies (ISO 4671) EN ISO 6179, Rubber, vulcanized or thermoplastic — Rubber sheets and rubber-coated fabrics — Determination of transmission rate of volatile liquids (gravimetric technique) (ISO 6179) EN ISO 7233, Rubber and plastics hoses and hose assemblies — Determination of resistance to vacuum (ISO 7233) EN ISO 7326, Rubber and plastics hoses — Assessment of ozone resistance under static conditions (ISO 7326) EN ISO 8031, Rubber and plastics hoses and hose assemblies — Determination of electrical resistance and conductivity (ISO 8031) EN ISO 8033, Rubber and plastics hoses — Determination of adhesion between components (ISO 8033:2016) EN ISO 8330, Rubber and plastics hoses and hose assemblies — Vocabulary (ISO 8330) EN ISO 10619-1, Rubber and plastics hoses and tubing — Measurement of flexibility and stiffness — Part 1: Bending tests at ambient temperature (ISO 10619-1) EN ISO 10619-2, Rubber and plastics hoses and tubing — Measurement of flexibility and stiffness — Part 2: Bending tests at sub-ambient temperatures (ISO 10619-2) ISO 37, Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties ISO 188, Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests ISO 1817, Rubber, vulcanized or thermoplastic — Determination of the effect of liquids ISO 4649, Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using a rotating cylindrical drum device SIST EN 1762:2019
Electrically conductive using a conductive rubber layer Discontinuous Electrically discontinuous SIST EN 1762:2019
two or more low resistance electrical bonding wires (grade “M” only); — an outer cover of black or coloured synthetic rubber, resistant to abrasion and outdoor exposure; the cover may be pricked to allow gas permeation. If the cover is not pricked a comparative measurement of permeation between the rubber materials of
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.