EN ISO 15615:2002
(Main)Gas welding equipment - Acetylene manifold systems for welding, cutting and allied processes - Safety requirements in high-pressure devices (ISO 15615:2002)
Gas welding equipment - Acetylene manifold systems for welding, cutting and allied processes - Safety requirements in high-pressure devices (ISO 15615:2002)
1 Scope
This standard lays down the general specifications, requirements and tests of devices located on the high-pressure side of acetylene manifold systems as defined in EN ISO 14114. The standard does not cover the high-pressure piping, flexible hoses and the regulator.
NOTE The terms "upstream" and "downstream" refer to the normal direction of gas flow in the device.
Gasschweißgeräte - Acetylenflaschen-Batterieanlagen für Schweißen, Schneiden und verwandte Prozesse - Sicherheitsanforderungen für Hochdruckeinrichtungen (ISO 15615:2002)
Diese Norm legt allgemeine Festlegungen, Anforderungen und Prüfungen für hochdruckseitig liegende Ausrüstungsteile in Acetylenflaschen-Batterieanlagen nach EN ISO 14114 fest. Diese Norm behandelt nicht die Hochdruckleitungen, Schlauchleitungen und den Druckregler.
ANMERKUNG Die Begriffe ¿anströmseitig" und ¿abströmseitig" beziehen sich auf die normale Gasdurchflussrichtung in der Einrichtung.
Matériel de soudage aux gaz - Centrales de détente pour la distribution d'acétylène pour le soudage, le coupage et les techniques connexes - Exigences de sécurité pour les dispositifs haute pression (ISO 15615:2002)
1 Domaine d'application
La présente norme fixe les spécifications générales, les exigences et les essais concernant des dispositifs utilisés sur le côté haute pression des centrales d'acétylène telles que définies dans l'EN ISO 14114. Elle ne traite pas des canalisations haute pression, des tuyaux souples et des détendeurs.
NOTE Les termes « amont » et « aval » se rapportent au sens normal de l'écoulement de gaz dans le dispositif.
Oprema za plamensko varjenje - Baterije acetilenskih jeklenk za varjenje, rezanje in sorodne postopke - Varnostne zahteve za visokotlačne naprave (ISO 15615:2002)
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.,62Gasschweißgeräte - Acetylenflaschen-Batterieanlagen für Schweißen, Schneiden und verwandte Prozesse - Sicherheitsanforderungen für Hochdruckeinrichtungen (ISO 15615:2002)Matériel de soudage aux gaz - Centrales de détente pour la distribution d'acétylene pour le soudage, le coupage et les techniques connexes - Exigences de sécurité pour les dispositifs haute pression (ISO 15615:2002)Gas welding equipment - Acetylene manifold systems for welding, cutting and allied processes - Safety requirements in high-pressure devices (ISO 15615:2002)25.160.30Varilna opremaWelding equipmentICS:Ta slovenski standard je istoveten z:EN ISO 15615:2002SIST EN ISO 15615:2003en01-maj-2003SIST EN ISO 15615:2003SLOVENSKI
STANDARD
SIST EN ISO 15615:2003
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 15615April 2002ICS 23.060.40; 25.160.30English versionGas welding equipment - Acetylene manifold systems forwelding, cutting and allied processes - Safety requirements inhigh-pressure devices (ISO 15615:2002)Matériel de soudage aux gaz - Centrales de détente pour ladistribution d'acétylène pour le soudage, le coupage et lestechniques connexes - Exigences de sécurité pour lesdispositifs haute pression (ISO 15615:2002)Gasschweißgeräte - Acetylenflaschen-Batterieanlagen fürSchweißen, Schneiden und verwandte Prozesse -Sicherheitsanforderungen für Hochdruckeinrichtungen (ISO15615:2002)This European Standard was approved by CEN on 30 December 2001.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 15615:2002 ESIST EN ISO 15615:2003
EN ISO 15615:2002 (E)2ContentspageForeword.31Scope.42Normative references.43Terms and definitions.44Design and materials.54.1Design.54.2Materials.55Requirements.55.1General.55.2General requirements.55.3Additional requirements to be met by specific types of devices.66Type tests.76.1General.76.2Reference values and accuracy of instruments.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.