EN ISO 4613-2:1995

SLOVENSKI STANDARD
01-maj-1999
Polimerni materiali – Materiali za oblikovanje in ekstrudiranje iz kopolimera
etilen/vinil acetata – 2. del: Priprava preskušancev in ugotavljanje lastnosti (ISO
4613-2:1995)
Plastics - Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials - Part 2:
Preparation of test specimens and determination of properties (ISO 4613-2:1995)
Kunststoffe - Ethylen-Vinylacetat (E/VAC) Formmassen - Teil 2: Herstellung von
Probekörpern und Bestimmung von Eigenschaften (ISO 4613-2:1995)
Plastiques - Matériaux a base d'éthylene/acétate de vinyle (E/VAC) pour moulage et
extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés (ISO
4613-2:1995)
Ta slovenski standard je istoveten z: EN ISO 4613-2:1995
ICS:
83.080.20 Plastomeri Thermoplastic materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

INTERNATIONAL ISO
STANDARD
4613-2
Second edition
1995-08-15
Plastics - Ethylenelvinyl acetate (E/VAC)
moulding and extrusion materials -
Part 2:
Preparation of test specimens and
determination of properties
Plas tiques - &hylene/ac&ate de vinye (E/vAC) pour moulage et
extrusion -
Partie 2: Prdpara tion des bprouve ttes et determina tion des propri&&
Reference number
ISO 46132:1995(E)
ISO 4613=2:1995(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national Standards bodies (ISO member bodies). The work
of preparing International Standards is normally carried out through ISO
technical committees. Esch member body interested in a subject for
- which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(1 EC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 4613-2 was prepared by Technical Committee
ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic materials.
This second edition cancels and replaces the first edition
(ISO 4613-2:1989) and includes the following changes:
The text has been brought into accordance with the frame text developed
by SC 9. The table of test methods has been revised in accordance with
ISO 10350.
ISO 4613 consists of the following Parts, under the general title
Plas tics - Ethylene/vinyl acetate (E/vAC) moulding and extrusion ma-
terials:
- Part 7: Designa tion and specifica tion
- Part 2: Preparation of test specimens and determination of proper-
ties
0 ISO 1995
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronie or mechanical, including photocopyrng and
microfilm, without Permission in writing from the publisher.
International anization fo r Standardiza tion
arg
Case Postale 56 . Cl-l-121 Geneve 20 l Switzerland
Pnnted in Switzerland
ii
INTERNATIONAL STANDARD 0 ISO ISO 4613=2:1995(E)
Plastics - Ethylene/vinyl acetate (E/VAC) moulding
and extrusion materials -
Part 2:
Preparation of test specimens and determination of
properties
2 Normative references
1 Scope
The following Standards contain provisions which,
through reference in this text, constitute provisions
of this part of ISO 4613. At the time of publication, the
This part of ISO 4613 specifies the methods of prep-
editions indicated were valid. All Standards are subject
aration of test specimens and the test methods to be
to revision, and Parties to agreements based on this
used in determining the properties of E/VAC moulding
part of ISO 4613 are encouraged to investigate the
and extrusion materials. Requirements for handling
possibility of applying the most recent editions of the
test material and for conditioning both the test ma-
Standards indicated below. Members of IEC and ISO
terial before moulding and the specimens before
maintain registers of currently valid International
testing are given here.
Standards.
Procedures and conditions for the preparation of test
ISO 62:1980, Plastics - Determination of water ab-
specimens and procedures for measuring properties
sorp tion.
of the materials from which these specimens are
made are given. Properties and test methods which
- Determination of tempera-
ISO 75-1: 1993, Plastics
are suitable and necessary to characterize E/VAC
ture of deflection under load - Part 1: General test
moulding and extrusion materials are listed.
method.
The properties have been selected from the general
ISO 75-2: 1993, Plastics - Determination of tempera-
test methods in ISO 10350. Other test methods in
ture of deflection under load - Part 2: Plastics and
wide use for or of particular significance to these
ebonite.
moulding and extrusion materials are also included in
this part of ISO 4613, as are the designatory proper- - Determination of flexural
ISO 178: 1993, Plastics
ties specified in part 1.
properties.
- Determination of Charpy
In Order to obtain reproducible and comparable test ISO 179: 1993, Plastics
results, it is necessary to use the methods of prep- impact strength.
aration and conditioning, the specimen dimensions
ISO 29111977, Plastics - Standard atmospheres for
and the test procedures specified herein Values de-
conditioning and testing.
termined will not necessarily be identical to those
obtained using specimens of different dimensions or
ISO 293:1986, Plastics - Compression moulding test
prepared using different procedures.
specimens of thermopfastic materiak.

ISO 4613=2:1995(E) 0 ISO
ISO 527-1 :1993, Plastics - Determination of tensile - Acquisition and presen-
ISO 10350: 1993, Plastics
Part 1: General principles.
properties - ta tion of comparable Single-poin t da ta.
ISO 527-2: 1993, Plastics - Determination of tensile IEC 93:1980, Methods of test for volume resistivity
properties - Part 2: Test conditions for moulding and and surface resistivity of solid electrical insulating
extrusion plas tics. ma terials.
ISO 527-4: -l 1, Plas tics - Determination of tensile IEC 112: 1979, Method for determining the compara-
properties - Part 4: Test conditions for isotropic and tive and the proof tracking indices of solid insulating
ortho tropic fibre-rein forced plas tic composites. ma terials under moist conditions.
ISO 899-1: 1993, Plastics - Determination of creep
IEC 243-1: 1988, Methods of test for electric strength
behaviour - Part 1: Tensile creep.
o f solid insula ting ma terials - Part 1: Tests at po wer
frequencies.
ISO 1133:1991, Plastics
- Determination of the melt
mass-flow rate (
...