CEN ISO/TS 24534-2:2007

SLOVENSKI STANDARD
01-april-2008
$YWRPDWLþQDLGHQWLILNDFLMDYR]LOLQRSUHPH(OHNWURQVNDLGHQWLILNDFLMDUHJLVWUDFLMH
(5,]DYR]LODGHO2SHUDWLYQH]DKWHYH,6276
Automatic vehicle and equipment identification - Electronic Registration Identification
(ERI) for vehicles - Part 2: Operational requirements (ISO/TS 24534-2:2007)
Straßenverkehrstelematik (RTTT) - Automatische Identifizierung von Fahrzeugen und
Ausrüstungen - Elektronische Identifizierung für die Registrierung (ERI) - Teil 2:
Betriebsanforderungen (ISO/TS 24534-2:2007)
Identification automatique des véhicules et des équipements - Identification
d'enregistrement électronique (ERI) pour les véhicules - Partie 2: Exigences de
fonctionnement (ISO/TS 24534-2:2007)
Ta slovenski standard je istoveten z: CEN ISO/TS 24534-2:2007
ICS:
03.220.20
35.240.60
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

TECHNICAL SPECIFICATION
CEN ISO/TS 24534-2
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
December 2007
ICS 35.240.60; 03.220.20
English Version
Automatic vehicle and equipment identification - Electronic
Registration Identification (ERI) for vehicles - Part 2: Operational
requirements (ISO/TS 24534-2:2007)
Identification automatique des véhicules et des Straßenverkehrstelematik (RTTT) - Automatische
équipements - Identification d'enregistrement électronique Identifizierung von Fahrzeugen und Ausrüstungen -
(ERI) pour les véhicules - Partie 2: Exigences de Elektronische Identifizierung für die Registrierung (ERI) -
fonctionnement (ISO/TS 24534-2:2007) Teil 2: Betriebsanforderungen (ISO/TS 24534-2:2007)
This Technical Specification (CEN/TS) was approved by CEN on 24 July 2006 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TS 24534-2:2007: E
worldwide for CEN national Members.

Contents Page
Foreword.3

Foreword
This document (CEN ISO/TS 24534-2:2007) has been prepared by Technical Committee CEN/TC 278 "Road
transport and traffic telematics", the secretariat of which is held by NEN, in collaboration with Technical
Committee ISO/TC 204 "Transport information and control systems".
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this CEN Technical Specification: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
TECHNICAL ISO/TS
SPECIFICATION 24534-2
First edition
2007-12-15
Automatic vehicle and equipment
identification — Electronic Registration
Identification (ERI) for vehicles —
Part 2:
Operational requirements
Identification automatique des véhicules et des équipements —
Identification d'enregistrement électronique (ERI) pour les véhicules —
Partie 2: Exigences de fonctionnement

Reference number
ISO/TS 24534-2:2007(E)
©
ISO 2007
ISO/TS 24534-2:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved

ISO/TS 24534-2:2007(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 2
4 Abbreviations . 4
5 Onboard ERI equipment requirements. 5
5.1 ERI System context . 5
5.2 ERT. 5
5.3 Operational parameters . 5
5.4 ERT memory allocation. 7
5.5 Security of ERI data. 8
5.6 Onboard ERI equipment categories. 8
5.7 ERT location . 8
5.8 Onboard ERI equipment safety . 8
5.9 Environmental requirements . 9
5.10 ERT security . 9
5.11 ERT Life cycle . 9
6 ERI system organizational framework. 10
Annex A (informative) Example user requirements and operational scenarios. 11
Annex B (informative) Typical operational usage of onboard ERI equipment. 15
Annex C (informative) Example of ERI system stakeholders . 16
Bibliography . 17

ISO/TS 24534-2:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
In other circumstances, particularly when there is an urgent market requirement for such documents, a
technical committee may decide to publish other types of normative document:
— an ISO Publicly Available Specification (ISO/PAS) represents an agreement between technical experts in
an ISO working group and is accepted for publication if it is approved by more than 50 % of the members
of the parent committee casting a vote;
— an ISO Technical Specification (ISO/TS) represents an agreement between the members of a technical
committee and is accepted for publication if it is approved by 2/3 of the members of the committee casting
a vote.
An ISO/PAS or ISO/TS is reviewed after three years in order to decide whether it will be confirmed for a
further three years, revised to become an International Standard, or withdrawn. If the ISO/PAS or ISO/TS is
confirmed, it is reviewed again after a further three years, at which time it must either be transformed into an
International Standard or be withdrawn.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO/TS 24534-2 was prepared by Technical Committee ISO/TC 204, Intelligent transport systems, and by
Technical Committee CEN/TC 278, Road transport and traffic telematics in collaboration.
ISO/TS 24534 consists of the following parts, under the general title Automatic vehicle and equipment
identification — Electronic Registration Identification (ERI) for vehicles:
— Part 1: Architecture
— Part 2: Operational requirements
— Part 3: Vehicle data
— Part 4: Secure communications using asymmetrical techniques
⎯ Part 5: Secure communications using symmetrical techniques
iv © ISO 2007 – All rights reserved

ISO/TS 24534-2:2007(E)
Introduction
A quickly emerging need has been identified with administrations to improve the unique identification of
vehicles for a variety of services. Situations are already occurring where manufacturers intend to fit lifetime
tags to vehicles. Various governments are considering the needs and benefits of Electronic Registration
Identification (ERI) as a legal proof of vehicle identity with potential mandatory uses. There is commercial and
economic justification both in respect of tags and infrastructure that a standard enables an interoperable
solution.
ERI is a means of uniquely identifying road vehicles. The application of ERI will offer significant benefits over
existing techniques for vehicle identification. It will be a suitable tool for the future management and
administration of traffic and transport, including applications in free-flow, multi-lane traffic conditions with the
capability to support mobile transactions. ERI addresses the need of authorities and other road users for a
trusted electronic identification, including roaming vehicles.
The unique vehicle identifier is held in a secure environment within an Electronic Registration Tag (ERT) fitted
to a vehicle. The identifier used to identify a vehicle is called the vehicle identifier or vehicleId. The preferred
identifier is the VIN, assigned to the vehicle by its manufacturer in accordance with ISO 3779, or it may be a
variant of this identifier.
The ERT may contain vehicle data in addition to the unique identifier, as required by authorities or their agents
for ERI applications (e.g. vehicle registration details). An ERT is the core component for simple to complex
applications of ERI, ranging from a simple read-only device, with more
...