EN 10149-2:1995
(Main)Hot-rolled flat products made of high yield strength steels for cold forming - Part 2: Delivery conditions for thermomechanically rolled steels
Hot-rolled flat products made of high yield strength steels for cold forming - Part 2: Delivery conditions for thermomechanically rolled steels
Part 2 of this European Standard, in addition to part 1, specifies requirements for flat products made of weldable, hot-rolled, high yield strength steels for cold forming. The grades are given in table 1 (chemical composition) and table 2 (mechanical properties) and are supplied in the thermomechanically rolled delivery condition as given in 7.2. The steels specified in this European Standard are applicable to hot-rolled flat products in the thickness range of 1,5 mm to 20 mm for the steels which have a specified minimum yield strength of 315 N/mm2 up to and including 460 N/mm2 and 1,5 mm to 16 mm for the steels which have a specified minimum yield strength of 500 N/mm2 up to and including 700 N/mm2.
Warmgewalzte Flacherzeugnisse aus Stählen mit hoher Streckgrenze zum Kaltumformen - Teil 2: Lieferbedingungen für thermomechanisch gewalzte Stähle
Der Teil 2 dieser Europäischen Norm gilt in Verbindung mit Teil 1 für Flacherzeugnisse aus warmgewalzten, schweißbaren Stählen mit hoher Streckgrenze, die für die Kaltumformung bestimmt sind. Die Stahlsorten werden mit den Anforderungen nach Tabelle 1 (chemische Zusammensetzung) sowie nach Tabelle 2 (mechanische Eigenschaften) im thermomechanisch gewalzten Zustand nach 7.2 geliefert.
Produits plats laminés à chaud en aciers à haute limite d'élasticité pour formage à froid - Partie 2: Conditions de livraison des aciers obtenus par laminage thermomécanique
La partie 2 de la présente norme européenne, vient s'ajouter à la partie 1, et spécifie les caractéristiques des produits plats en aciers soudables à haute limite d'élasticité, laminés à chaud pour formage à froid. Les nuances sont données au tableau 1 (composition chimique) et au tableau 2 (caractéristiques mécaniques) et sont livrées à l'état de laminage thermomécanique comme indiqué en 7.2.
Vroče valjani ploščati izdelki za hladno preoblikovanje iz jekel z veliko napetostjo tečenja - 2. del: Dobavni pogoji za termomehansko valjana jekla
General Information
- Status
- Withdrawn
- Publication Date
- 09-Sep-1995
- Withdrawal Date
- 24-Sep-2013
- Technical Committee
- ECISS/TC 103 - Structural steels other than reinforcements
- Drafting Committee
- ECISS/TC 10 - Structural steels - Qualities
- Current Stage
- 9960 - Withdrawal effective - Withdrawal
- Start Date
- 25-Sep-2013
- Completion Date
- 25-Sep-2013
Relations
- Effective Date
- 19-Sep-2009
- Effective Date
- 28-Jan-2026
Frequently Asked Questions
EN 10149-2:1995 is a standard published by the European Committee for Standardization (CEN). Its full title is "Hot-rolled flat products made of high yield strength steels for cold forming - Part 2: Delivery conditions for thermomechanically rolled steels". This standard covers: Part 2 of this European Standard, in addition to part 1, specifies requirements for flat products made of weldable, hot-rolled, high yield strength steels for cold forming. The grades are given in table 1 (chemical composition) and table 2 (mechanical properties) and are supplied in the thermomechanically rolled delivery condition as given in 7.2. The steels specified in this European Standard are applicable to hot-rolled flat products in the thickness range of 1,5 mm to 20 mm for the steels which have a specified minimum yield strength of 315 N/mm2 up to and including 460 N/mm2 and 1,5 mm to 16 mm for the steels which have a specified minimum yield strength of 500 N/mm2 up to and including 700 N/mm2.
Part 2 of this European Standard, in addition to part 1, specifies requirements for flat products made of weldable, hot-rolled, high yield strength steels for cold forming. The grades are given in table 1 (chemical composition) and table 2 (mechanical properties) and are supplied in the thermomechanically rolled delivery condition as given in 7.2. The steels specified in this European Standard are applicable to hot-rolled flat products in the thickness range of 1,5 mm to 20 mm for the steels which have a specified minimum yield strength of 315 N/mm2 up to and including 460 N/mm2 and 1,5 mm to 16 mm for the steels which have a specified minimum yield strength of 500 N/mm2 up to and including 700 N/mm2.
EN 10149-2:1995 is classified under the following ICS (International Classification for Standards) categories: 77.140.50 - Flat steel products and semi-products. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 10149-2:1995 has the following relationships with other standards: It is inter standard links to EN 10149-2:2013, EN 13001-3-1:2012. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 10149-2:1995 is associated with the following European legislation: EU Directives/Regulations: 97/23/EC; Standardization Mandates: M/005, M/071. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
EN 10149-2:1995 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Warmgewalzte Flacherzeugnisse aus Stählen mit hoher Streckgrenze zum Kaltumformen - Teil 2: Lieferbedingungen für thermomechanisch gewalzte StähleProduits plats laminés a chaud en aciers a haute limite d'élasticité pour formage a froid - Partie 2: Conditions de livraison des aciers obtenus par laminage thermomécaniqueHot-rolled flat products made of high yield strength steels for cold forming - Part 2: Delivery conditions for thermomechanically rolle
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...