EN 10363:2016

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kontinuierlich warmgewalztes Riffelband und -blech abgelängt aus Warmbreitband - Grenzabmaße und FormtoleranzenContinuously hot-rolled patterned steel strip and plate/sheet cut from wide strip - Tolerances on dimensions and shape77.140.50SROL]GHONLFlat steel products and semi-products17.040.10Tolerance in ujemiLimits and fitsICS:Ta slovenski standard je istoveten z:EN 10363:2016SIST EN 10363:2016en,fr,de01-oktober-2016SIST EN 10363:2016SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10363
July
t r s x ICS
y yä s v rä w r English Version
Continuously hotærolled patterned steel strip and dimensions and shape larges bandes en acier laminß à chaud en continu æ tolßrances sur les dimensions et la forme
Kontinuierlich warmgewalztes Riffelband und æblech abgelängt aus Warmbreitband aus Stahl æ Grenzabmaße und Formtoleranzen This European Standard was approved by CEN on
s w April
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s x CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s r u x uã t r s x ESIST EN 10363:2016

Standards with steel grades for this dimensional standard . 14 Annex B (informative)
Indicative typical weight . 15 Bibliography . 16
· 600 mm)a Sheet/plate cut from wide strip Strip w < 600 mm slit from wide strip
¶ 20 mm EN 10025–2 EN 10025–3 EN 10025–4 EN 10025–5 EN 10149–2 a Usually these steel products are delivered in widths up to and including 2 200 mm. For widths values w over 2 200 mm, see 4.2, Option 4.
Steel grades other than those given in Table 1 may be used by agreement only. This European standard does not apply to stainless steels. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10020:2000, Definition and classification of grades of steel EN 10079:2007, Definition of steel products 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 10020:2000, EN 10079:2007 and the following apply. 3.1 hot-rolled patterned steel strip hot-rolled steel strip which has been provided with a regular raised pattern (chequer or bulb) on one side to render the surface more non-slip and safer underfoot, with the reverse side usually smooth 4 Information to be supplied by the purchaser 4.1 General The following information shall be supplied by the purchaser at the time of enquiry and order: a) quantity to be supplied; b) product designation (wide strip, sheet/plate cut from wide strip, strip slit from wide strip); c) the number of this standard (EN 10363); SIST EN 10363:2016

t
t r r mm (see Table 2, Footnote a); 5) special tolerances on width for products with trimmed edges (see Table 3, Footnote b). If the customer does not specify otherwise, delivery shall be in accordance with the specifications of 4.1 and 5.1. 4.3 Example of designations The designation shall be followed by the complete designation of the steel ordered. EXAMPLE 1 Designation of an order of 20 t of hot-rolled patterned wide strip according to this European Standard, of surface design T, a nominal thickness of 5 mm and a nominal width of 1 300 mm, made from steel of grade S235JR (material number 1.0038) in accordance with EN 10025–2: 20 t strip EN 10363 — T – 5 × 1300 Steel EN 10025–2 — S235JR or 20 t strip EN 10363 — T – 5 × 1300 Steel EN 10025–2 — 1.0038 SIST EN 10363:2016

3,0 mm and between 0,5 mm and 2,2 mm for nominal thicknesses t < 3,0 mm. 5.2.3 Informative values for nominal masses are given in Annex B, Table B.1. 5.2.4 The dimensions given in Figures 1, 2 and 3 are guideline values. 5.2.5 Embossing need not run parallel with the longitudinal edges of the strip or sheet/plate. SIST EN 10363:2016

Figure 1 — Example of surface design T
Figure 2 — Example of surface design R SIST EN 10363:2016

Figure 3 — Example of surface design A 6 Tolerances for sheet/plate 6.1 Thickness 6.1.1 The nominal thickness of the product t is always the thickness of the core without the pattern (see Figure 4). The height of the pattern h is at the discretion of manufacturer in the following ranges (see also 5.2.2): a) 1,0 mm
¶ h
¶ 2,2 mm for nominal thickness t ≥ 3,0 mm; and b) 0
...