ECISS/TC 103 - Structural steels other than reinforcements

This document specifies the tolerances on dimensions, squareness of ends, straightness and mass of cold formed steel sheet piles and is designed to be read in conjunction with EN 10249-1.
This document specifies the tolerances of cold formed steel sheet piles produced from hot rolled strip or sheet with a thickness equal to or greater than 3 mm.
The products specified are for general, structural and civil engineering works. The types of steel sheet piles covered by this document are: Z-shaped, Omega-shaped and trench sheets.
This document also specifies options that can be agreed between the purchaser and the manufacturer at the time of the order and enquiry.

This document specifies the tolerances on dimensions, squareness of ends, straightness and mass of hot rolled steel sheet piles and is designed to be read in conjunction with EN 10248-1.
The products specified are for general, structural and civil engineering works. The types of steel sheet piles covered by this document are: Z-shaped, U-shaped, straight web, H-shaped with their interlocking bars.
This document also specifies options that can be agreed between the purchaser and the manufacturer at the time of the order and enquiry.

This document specifies tolerances on dimensions and shape for continuously hot-rolled uncoated plate/sheet and strip with a maximum width of 2 200 mm and a maximum thickness of 25 mm of non-alloy and alloy steels in accordance with Table 1 (see also Annex B). This document also applies to hot-rolled strip for cold rolling.
Table 1 - Field of application
[...table not represented...]
NOTE 1   This document does not apply to:
-   hot-rolled strip rolled in widths w < 600 mm (see EN 10048);
-   hot-rolled patterned steel strip and plate/sheet cut from wide strip (EN 10363);
-   uncoated or electrolytically coated cold rolled sheet and strip (see EN 10131);
-   hot-dip coated steel sheet and strip (EN 10143);
-   stainless steels.
NOTE 2   This document can also be used for steels from other standards, e. g. steels for shipbuilding.

This document provides requirements for the statistical distribution of material properties and dimensional parameters of structural steel products, allowing the proof of consistency of the safety approach of the properties of the product standards compared to those of the design standards for the design of steel buildings. It also describes the evaluation procedures for the verification of the compliance of structural steels with these requirements.
This document applies for the following structural steel products intended for buildings: hot rolled and welded I- and H-sections, hot rolled plates rolled on a reversing mill, sheets/plates cut from hot-rolled wide strip and hot finished and cold formed welded structural hollow sections.
It is intended to be used as a background document to support the assessment of the partial factors for steel constructions (as detailed in EN 1993-1-1).
This document can be used for neither product ordering nor certification.
NOTE   The background of statistical requirements on mechanical properties and geometrical parameters is detailed in EN 1993-1-1:2022, Annex E.

This document specifies requirements for weldable structural steels made of hot finished seamless and high frequency welded hollow sections to be used in the fabrication of fixed offshore structures.
The following thickness limitations are given in this standard:
-   for seamless hollow sections up to and including 65 mm;
-   for HFW hollow sections up to and including 25,4 mm.
Greater thicknesses can be agreed, provided the technical requirements of this European Standard are maintained.
This European Standard is applicable to steels for offshore structures, designed to operate in the offshore sector but not to steels supplied for the fabrication of subsea pipelines, risers, process equipment, process piping and other utilities. It is primarily applicable to the North Sea Sector, but may also be applicable in other areas provided that due consideration is given to local conditions e.g. design temperature.
NOTE   This document has an informative Annex E on the prequalification of steels for fixed offshore structures in arctic areas.
Minimum yield strengths up to 770 MPa are specified together with impact properties at temperatures down to -40 °C.

This document specifies the requirements for hot rolled steel sheet piles in respect of its chemical composition, mechanical properties and conditions of delivery.
The products specified are for general, structural and civil engineering works. The types of steel sheet piles covered by this document are: Z-shaped, U-shaped, straight web, H-shaped with their interlocking bars. The types of interlocks and the requirements in respect of tolerances on shape and dimensions are specified in Part 2 of this document.

This document specifies technical delivery conditions for flat and long products of hot rolled weldable fine grain structural steels in the thermomechanical rolled condition in the grades and qualities given in Tables 1 to 3 (chemical composition) and Tables 4 to 6 (mechanical properties) in thickness ≤ 150 mm.
The steels specified in this document are especially intended for use in heavily loaded parts of welded structures such as, bridges, flood gates, storage tanks, water supply tanks, etc., for service at ambient and low temperatures.

This document specifies technical delivery conditions for flat products of high yield strength alloy special steels. The grades and qualities are given in Tables 1 to 3 (chemical composition) and Tables 4 to 6 (mechanical properties) and are supplied in the quenched and tempered condition.
The steels specified in this document are applicable to hot-rolled flat products with a minimum nominal thickness of 3 mm and a maximum nominal thickness of 200 mm for grades S460, S500, S550, S620 and S690, a maximum nominal thickness of 125 mm for grades S890 and S960, in steels which, after quenching and tempering, have a specified minimum yield strength of 460 MPa to 960 MPa.

This document specifies technical delivery conditions for high strength and weather resistant hot-finished seamless, electric welded and submerged arc welded steel structural hollow sections of circular, square, rectangular or elliptical forms.
It applies to hollow sections formed hot, with or without subsequent heat treatment, or formed cold with subsequent heat treatment above 580 °C to obtain equivalent mechanical properties to those obtained in the hot formed product.
NOTE 1   The requirements for tolerances, dimensions and sectional properties are specified in EN 10210-2.
NOTE 2   The attention of users is drawn to the fact that whilst cold formed grades in EN 10219-3 can have equivalent mechanical properties to hot-finished grades in this document the sectional properties of square and rectangular hollow sections in EN 10210-2 and EN 10219-2 are not equivalent.
NOTE 3   A range of material grades is specified in this document and the user can select the grade most appropriate to the intended use and service conditions. The grades and mechanical properties of the finished hollow sections are generally comparable with those in EN 10025-4, EN 10025-5 and EN 10025-6.
NOTE 4   The requirements for seamless and welded steel structural hollow sections for use in offshore structures are covered in the EN 10225 series.
NOTE 5    Spiral welded hollow sections are expected to be used with caution in applications involving dynamic behaviour (fatigue stress) as, up to now, there is insufficient data regarding their performance.

This document specifies the technical delivery conditions for high strength and weather resistant electric welded and submerged arc welded cold formed steel structural hollow sections of circular, square, rectangular or elliptical forms and formed cold without subsequent heat treatment other than the heat treatment of the weld line.
NOTE 1   The requirements for tolerances, dimensions and sectional properties can be found in EN 10219 2.
NOTE 2   The attention of users is drawn to the fact that whilst cold formed grades in this document can have equivalent mechanical properties to hot-finished grades in EN 10210 3, the sectional properties of square and rectangular hollow sections in EN 10219 2 and EN 10210 2 are not equivalent.
NOTE 3   A range of steel grades is specified in this document and the user can select the grade most appropriate to the intended use and service conditions. The grades and mechanical properties, but not the final supply condition of cold formed hollow sections are generally comparable with those in EN 10025 3, EN 10025 4, EN 10025 5, EN 10025 6, EN 10149 2 and EN 10149 3.

This document specifies technical delivery conditions for flat and long products of hot rolled steels with improved atmospheric corrosion resistance in the grades and qualities given in Tables 2 and 3 (chemical composition) and Tables 4 and 5 (mechanical properties) in the usual delivery conditions as given in 6.3.
The thicknesses in which products of the steel grades and qualities specified in this document can be supplied are given in Table 1.
Table 1 - Product forms for the different steel grades with improved atmospheric corrosion resistance depending on their thickness
[table not reproduced]
The steels specified in this document are not intended to be heat treated except products delivered in the delivery condition +N. Stress relieving is accepted. Products delivered in +N condition can be hot formed and/or normalized after delivery (see Clause 3).

This document specifies the technical delivery conditions for flat and long products as well as semi-finished products which are meant for further processing to flat and long products of hot rolled non-alloy quality steels in the grades and qualities given in Tables 1 to 5 (chemical composition) and Tables 6 to 8 (mechanical properties) in the usual delivery conditions as given in 6.3. Three engineering steels are also specified in this document (see Tables 2 and 4) (chemical composition) and Table 7 (mechanical properties). This document does not apply to structural hollow sections (see EN 10210 1 and EN 10219 1) and tubes.
The technical delivery conditions apply to:
-   thicknesses ≥ 3 mm and ≤ 150 mm for long products of steel grade S460JR, J0, J2, K2 and S500J0;
-   thicknesses ≤ 400 mm for flat products of qualities JR, J0, J2 and K2;
-   thicknesses ≤ 250 mm for flat and long products of all other grades and qualities.
The steels specified in this document are not intended to be heat treated except products delivered in the delivery condition +N. Stress relieving is accepted. Products delivered in +N condition can be hot formed and/or normalized after delivery (see Clause 3).
This document foresees that semi-finished products which are to be converted to rolled finished products conforming to this document are the subject of special agreements at the time of the order. The chemical compositions are also agreed to at the time of the order; the values are within the limits of Tables 1 and 2.
For certain grades and product forms suitability for particular applications are specified at the time of the order (see 7.4.2, 7.4.3 and Table 9).

This document specifies technical delivery conditions for flat and long products of hot rolled weldable fine grain structural steels in the normalized/normalized rolled delivery condition in the grades and qualities given in Tables 1 to 3 (chemical composition) and Tables 4 to 6 (mechanical properties) in thickness ≤ 250 mm.
The steels specified in this document are especially intended for use in heavily loaded parts of welded structures such as, bridges, flood gates, storages tanks, water supply tanks, etc., for service at ambient and low temperatures.

This document specifies requirements for submerged arc welded (SAW) and high frequency welded (HFW) cold formed hollow sections to be used in the fabrication of fixed offshore structures.
The thickness limit for SAWL circular hollow sections is up to and including 50,8 mm, for HFW circular hollow sections up to and including 25,4 mm and for HFW square and rectangular hollow sections up to and including 12,5 mm.
Greater thicknesses for SAWL hollow sections can be agreed provided the technical requirements of this European Standard are maintained.
NOTE 1   This document has an Annex E for SAWH round hollow sections with a thickness limit of 30,0 mm, and an Annex F for high strength square and rectangular HFW hollow sections made of steel grades S500 to S700.
This European Standard is applicable to steels for offshore structures designed to operate in the offshore sector but not to steels supplied for the fabrication of subsea pipelines, risers, process equipment, process piping and other utilities. It is primarily applicable to the North Sea Sector, but may also be applicable in other areas provided that due consideration is given to local conditions e.g. design temperature.
NOTE 2   This document has an informative Annex G on the prequalification of steels for fixed offshore structures in arctic areas.
Minimum yield strengths up to 700 MPa are specified together with impact properties at temperatures down to -40 °C.
NOTE 3   A range of material grades is specified in this standard and the user can select the grade most appropriate to the intended use and its service condition.

This document specifies requirements for weldable structural steels, in the form of sections (e.g. H-, I-, Z-sections, U-channels, angles and tees) excluding hollow sections, to be used in the fabrication of fixed offshore structures. The thickness limitation in this standard is up to and including 63 mm.
For steel qualities with mechanical properties in the transverse direction (named xL1O) sections with flange widths smaller than 180 mm and channels with flange widths smaller than 90 mm cannot be ordered.
Greater thicknesses may be agreed, provided the technical requirements of this European Standard are maintained.
This European Standard is applicable to steels for offshore structures, designed to operate in the offshore sector but not to steels supplied for the fabrication of subsea pipelines, risers, process equipment, process piping and other utilities. It is primarily applicable to the North Sea Sector, but may also be applicable in other areas provided that due consideration is given to local conditions e.g. design temperature.
NOTE   This document has an informative Annex C on the prequalification of steels for fixed offshore structures in arctic areas.
Minimum yield strengths up to 460 MPa are specified together with impact properties at temperatures down to -40 °C.

This document specifies requirements for weldable structural steels, in the form of plates, to be used in the fabrication of fixed offshore structures.
The following thickness limitations are given in this standard:
- S355NLO up to and including 200 mm;
- S355MLO, S420MLO, S460MLO, S500MLO up to and including 120 mm;
- S420QLO, S460QLO, S500QLO, S550QLO, S620QLO, S690QLO up to and including 150 mm.
Greater thicknesses can be agreed, provided the technical requirements of this European Standard are maintained.
This European Standard is applicable to steels for offshore structures, designed to operate in the offshore sector, including plate for structural hollow sections (see EN 10225-4). It does not apply to plates supplied for the fabrication of subsea pipelines, risers, process equipment, process piping and other utilities. It is primarily applicable to the North Sea Sector, but may also be applicable in other areas provided that due consideration is given to local conditions e.g. design temperature.
NOTE   This document has an informative Annex F on the prequalification of steels for fixed offshore structures in arctic areas.
Minimum yield strengths up to 690 MPa are specified together with impact properties at temperatures down to -40 °C.

This document specifies tolerances for hot finished circular, square, rectangular and elliptical structural hollow sections, manufactured in wall thicknesses up to 120 mm, in the following size ranges:
-   Circular: Outside diameters up to 2 500 mm;
-   Square: Outside dimensions up to 800 mm × 800 mm;
-   Rectangular: Outside dimensions up to 750 mm × 500 mm;
-   Elliptical: Outside dimensions up to 500 mm × 250 mm.
The formulae for calculating sectional properties of sections manufactured to the dimensional tolerances of this standard, to be used for the purposes of structural design, are given in Annex A.
Dimensions and sectional properties for a limited range covering the more common sizes are given in Annex B.
NOTE   The designation of the sections' major axis (yy) and minor axis (zz) aligns with the axis designation used for structural design in the structural Eurocodes.

This document specifies tolerances for cold formed welded circular, square, rectangular and elliptical structural hollow sections, manufactured in wall thicknesses up to 40 mm, in the following size ranges:
-   circular: Outside diameters up to 2 500 mm;
-   square: Outside dimensions up to 500 mm × 500 mm;
-   rectangular: Outside dimensions up to 500 mm × 300 mm;
-   elliptical: Outside dimensions up to 480 mm × 240 mm.
The formulae for calculating sectional properties of sections manufactured to the dimensional tolerances of this standard, to be used for the purposes of structural design, are given in Annex A.
Dimensions and sectional properties for a limited range of more common sizes are given in Annex B.
NOTE   The designation of the sections' major axis (yy) and minor axis (zz) aligns with the axis designation used for structural design in the structural Eurocodes.

This document specifies the nominal dimensions and the tolerances on dimensions and shape of hot-rolled steel flat bars and steel wide flats for general purposes.
This document is not applicable to spring leaves, see EN 10092-1.

This document specifies deformation properties perpendicular to the surface of the product.
This document may be applied as a supplement to all product standards for flat products and sections of fully killed steels, except stainless steels. It covers products having a nominal thickness (t) between 15 mm and 400 mm of steels with a specified minimum upper yield strength ReH or proof strength Rp0,2 ≤ 960 MPa ) for which improved through thickness properties are required.
This document may be applied to other steel types if agreed at the time of the order.
This document may be applied to products with thickness between 10 mm ≤ t <15 mm if agreed at the time of the order. See option 1.
This document may be applied to products with thickness t > 400 mm if agreed at the time of the order. See Option 2.

This European Standard specifies requirements for the nominal dimensions of hot-rolled equal and unequal leg angles. This European Standard does not apply to angles with square roots. These requirements do not apply to equal and unequal leg angles rolled from stainless steel.

This European standard specifies the nominal dimensions and masses of the hot rolled steel channels, I and H sections.
The following shapes are covered by this standard:
Sections:
-   Parallel flange I sections IPE;
-   Wide flange beams HE;
-   Extra wide flange beams HL and HLZ;
-   Wide flange columns HD;
-   Wide flange bearing piles HP and UBP;
-   Universal beams UB;
-   Universal columns UC;
-   Taper flange I sections IPN and J.
Channels:
-   Parallel flange channels UPE and PFC;
-   Taper flange channels UPN, U and CH.
These requirements do not apply to hot rolled steel channels, I and H sections from stainless steel.

This European Standard specifies tolerances on dimensions and shape for continuously hot-rolled uncoated patterned steel strip and plate/sheet cut of it in nominal thicknesses up to 20 mm inclusive, of non-alloy and alloy steels in accordance with Table 1 (see also Annex A).
(...)
Steel grades other than those given in Table 1 may be used by agreement only.
This European standard does not apply to stainless steels.

This European Standard, in addition to EN 10149-1, specifies requirements for flat products made of weldable, hot-rolled, high yield strength steels for cold forming.
The grades are given in Table 1 (chemical composition) and Table 2 (mechanical properties) and are supplied in the thermomechanically rolled delivery condition as given in 7.2.
The steels specified in this European Standard are applicable to hot-rolled flat products in the thickness range of:
-   1,5 mm to 20 mm for the steels which have a specified minimum yield strength of 315 MPa ) up to and including 460 MPa1);
-   1,5 mm to 16 mm for the steels which have a specified minimum yield strength of 500 MPa1) up to and including 700 MPa1); and
-   from 2 mm up to 10 mm for the steels with a minimum yield stress in the range from 900 MPa1) to 960 MPa1).

1.1   This European Standard specifies requirements for flat products made of weldable, hot-rolled, high yield strength alloy quality and special steels for cold forming.
EN 10149-1 specifies the general delivery conditions.
EN 10149-2 specifies the delivery conditions for thermomechanically rolled steels in the grades given in Table 1 (chemical composition) and Table 2 (mechanical properties) of Part 2.
EN 10149-3 specifies the delivery conditions for normalised or normalised rolled steels in the grades given in Table 1 (chemical composition) and Table 2 (mechanical properties) of Part 3.
1.2   This European Standard does not apply to products for pressure vessels and products for which other European Standards exist or European Standards dealing with steels for general structural applications are being prepared:
-   Hot-rolled products of structural steels (see EN 10025 parts 1 to 6);
-   Hot finished structural hollow sections of non-alloy and fine grain steels (see EN 10210-1).

This European Standard, in addition to EN 10149-1, specifies requirements for flat products made of weldable, hot-rolled, high yield strength steels for cold forming.
The grades are given in Table 1 (chemical composition) and Table 2 (mechanical properties) and are supplied in the normalised or normalised rolled delivery condition as given in 7.2.
The steels specified in this European Standard are applicable to hot-rolled flat products in the thickness range of ≥ 1,5 mm and ≤ 20 mm.

This European Standard specifies tolerances on dimensions and shape for hot-rolled non-alloy and alloy steel plates with the following characteristics:
a)   Nominal thickness: 3 mm < or = t < or = 400 mm;
b)   Nominal width: w > or = 600 mm.
Tolerances for products of width w < 600 mm cut or slit from plate should be agreed between manufacturer and purchaser at the time of enquiry and order.
This European Standard applies, but is not limited, to steel grades defined in EN 10025-2 to
EN 10025-6:2004+A1:2009, EN 10028-2 to EN 10028-6, EN 10083-2 and EN 10083-3, EN 10084, EN 10085, EN 10149-2 and EN 10149-3, EN 10207 and EN 10225 (see also Annex A). It does not apply to stainless steels.
This European Standard does not include round plates, custom-made plates, chequer or bulb plate for flooring and wide flats.

This European Standard specifies requirements for automatically blast-cleaned and automatically
prefabrication primed structural steel products.
This European Standard does not cover manual blast cleaning and/or manual spray painting.
NOTE Where the steel is less than 5 mm thick, care should be exercised to ensure it is not deformed by blast
cleaning.

CMC - Modification to Clause 2

This part of this European Standard specifies the technical delivery conditions for cold formed welded structural hollow sections of circular, square or rectangular forms and applies to structural hollow sections formed cold without subsequent heat treatment.
Requirements for tolerances, dimensions and sectional properties are contained in EN 10219-2.
NOTE   A range of steel grades is specified in this European Standard and the user should select the grade appropriate to the intended use and service conditions. The grades and mechanical properties of the finished hollow sections are compatible with those in EN 10025-2 and EN 10025-3.

This part of this European Standard specifies technical delivery conditions for hot finished hollow sections of circular, square, rectangular or elliptical forms and applies to hollow sections formed hot, with or without subsequent heat treatment, or formed cold with subsequent heat treatment to obtain equivalent metallurgical conditions to those obtained in the hot formed product.
Requirements for tolerances, dimensions and sectional properties are contained in EN 10210-2.
NOTE   A range of material grades is specified in this standard and the user should select the grade appropriate to the intended use and service conditions. The grades and mechanical properties of the finished hollow sections are compatible with those in EN 10025-2 and EN 10025-3.

This CEN Technical Report provides guidance for forming during processing of structural steel products conforming to EN 10025 Parts 2 to 6 and EN 10149 Parts 2 and 3. This Technical Report covers hot and cold forming processes and local hot forming used in flame-straightening operations.
This Technical Report does not cover the special measures necessary for the fabrication of structural components that are subjected predominantly to alternating stresses or that come into contact with aggressive media.

1.1   This European Standard specifies the general requirements for the surface condition of hot-rolled steel plates, wide flats and sections. It covers the requirements on the type, the permissible depth and the permissible size of the surface area affected by:
¾ discontinuities (imperfections ant defects) and
¾ repairs by grinding and/or welding.
1.2   This European Standard shall be applied so far as no other requirements for the surface condition exist in the appropriate material or product standard. The requirements laid down in the appropriate material or product standard shall always prevail.
1.3   This Part 1 of this European Standard covers the general delivery requirements for the surface condition of hot-rolled steel products such as:
¾ plates and wide flats, see Part 2;
¾ sections, see Part 3;

This Part 3 in addition to Part 1 of this European Standard specifies the delivery requirements for surface condition of sections to which the European Standards mentioned in clause 2 apply and applies to all surfaces excluding edges.
NOTE   In this European Standard section toes (see EN 10055) are considered as part of the surfaces of a section.

This Part 2 in addition to Part 1 of this European Standard specifies the delivery requirements which apply to the surface condition of hot-rolled plates and surface condition of the faces of wide flats with thicknesses of 3 mm = t = 400 mm.
NOTE   For plates with a thickness > 400 mm special agreements should be made at the time of the order.

1.1 This document specifies requirements for flat and long products (see Clause 3) of hot rolled structural
steels excluding structural hollow sections and tubes. Part 1 of this document specifies the general delivery
conditions.
The specific requirements for structural steels are given in the following Parts:
Part 2: Technical delivery conditions for non-alloy structural steels
Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels
Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance
Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched
and tempered condition
The steels specified in this document are intended for use in welded, bolted and riveted structures.
1.2 This document does not apply to coated products or to steel products for general structural
applications in accordance with the standards and draft standards listed in the Bibliography.

This European Standard specifies the nominal dimensions and the tolerances on dimensions and shape of hot-rolled finished square steel bars for general purposes.

This European Standard specifies the nominal dimensions and the tolerances on dimensions and shape of hot-rolled steel hexagon bars.

This Part of this European Standard specifies the nominal dimensions and the tolerances on dimensions and shape of hot rolled steel flat bars for springs with three different types of profiles (A, B, and C). Formulas for calculation the moment of inertia are specified in annex A.
This standard is applicable only to spring steel flat bars produced from steel grades specified in EN 10089.

This European Standard specifies the nominal dimensions and the tolerances on dimensions and shape of hot-rolled round steel bars.

This Part of this European Standard specifies the nominal dimensions and the tolerances on dimensions and shape of hot rolled spring steel flat bars for ribbed and grooved spring leaves.
This standard is applicable only to steel flats produced from steel grades specified in EN 10089.

This European Standard specifies requirements for the tolerances on dimensions, shape and mass of hot-rolled steel channels with tapered flanges or parallel flanges. These requirements do not apply to channels produced from stainless steel.

This European Standard specifies requirements for the nominal dimensions and tolerances on shape, dimensions and mass of hot-rolled bulb flats. These requirements do not apply to bulb flats rolled from stainless steel.

This European Standard applies to uncoated hot rolled narrow steel strip, of width less than 600 mm, made of the steel grades covered by the following: EURONORMS 84, 96, 120, 156; European Standards EN 10025, EN 10028, EN 10083-1, EN 10083-2, EN 10083-3, EN 10113-2, EN 10113-3, EN 10155 and EN 10207; draft European Standards prEN 10088-2, prEN 10111, prEN 10137-2, prEN 10137-3, prEN 10149-2, prEN 10149-3 and prEN 10208-2. Note: This European Standard may be applied to other types of steels if agreed at the time of ordering.

This European standard specifies requirements for the nominal dimensions and the tolerances on dimensions, shape and mass of hot-rolled steel equal flange tees with radiused root and toes. These requirements do not apply to equal flange tees produced from stainless steel.

This part of this European Standard specifies the requirements for cold formed non alloy steel sheet piling produced from hot rolled strip or sheet with a thickness equal to or greater than 2mm in respect of its chemical composition, mechanical and technological properties and delivery conditions. The products specified are for general, structural and civil engineering works. Requirements concerning the tolerances on shape and dimensions are specified in Part 2 of this European Standard.

This European standard specifies requirements for tolerances on dimensions, shape and mass of hot-rolled taper flange I sections. These requirements do not apply to taper flange I sections produced from stainless steel.

This European standard specifies tolerances on shape dimensions and mass of structural steel I and H sections. These requirements do not apply to I and H sections rolled from stainless steel. These requirements do not apply to taper flange sections. Note: Until a European standard for dimensions of I and H beams is published, Euronorm 19 and Euronorm 53 or corresponding national standards may be used.

This part of this European standard specifies tolerances on shape dimensions and mass of hot-rolled structural steel equal and unequal leg angles. The sizes of these angles are given in EN 10056-1. These tolerances do not apply to equal and unequal leg angles produced from stainless steel. Note: until EN 10056-1 is published, either Euronorms 56 and 57 or the corresponding national standards may be used.

This document specifies the requirement for testing of special properties of hot-rolled steel sheet piles.