EN ISO 1:2016

SLOVENSKI STANDARD
01-december-2016
1DGRPHãþD
SIST EN ISO 1:2004
6SHFLILNDFLMHJHRPHWULMVNLKYHOLþLQL]GHOND*366WDQGDUGQDUHIHUHQþQD
WHPSHUDWXUD]DVSHFLILNDFLMRJHRPHWULMVNLKLQGLPHQ]LMVNLKODVWQRVWL,62
Geometrical product specifications (GPS) - Standard reference temperature for the
specification of geometrical and dimensional properties (ISO 1:2016)
Geometrische Produktspezifikation (GPS) - Referenztemperatur für geometrische
Produktspezifikation und -prüfung (ISO 1:2016)
Spécification géométrique des produits (GPS) - Température normale de référence pour
la spécification géométrique des produits et vérification (ISO 1:2016)
Ta slovenski standard je istoveten z: EN ISO 1:2016
ICS:
17.040.40 6SHFLILNDFLMDJHRPHWULMVNLK Geometrical Product
YHOLþLQL]GHOND*36 Specification (GPS)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 1
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2016
EUROPÄISCHE NORM
ICS 17.040.01 Supersedes EN ISO 1:2002
English Version
Geometrical product specifications (GPS) - Standard
reference temperature for the specification of geometrical
and dimensional properties (ISO 1:2016)
Spécification géométrique des produits (GPS) - Geometrische Produktspezifikation (GPS) -
Température normale de référence pour la Referenztemperatur für geometrische
spécification des propriétés géométriques et Produktspezifikation und -prüfung (ISO 1:2016)
dimensionnelles (ISO 1:2016)
This European Standard was approved by CEN on 7 August 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1:2016 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 1:2016) has been prepared by Technical Committee ISO/TC 213 "Dimensional
and geometrical product specifications and verification" in collaboration with Technical Committee
CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of
which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2017, and conflicting national standards shall
be withdrawn at the latest by March 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 1:2002.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 1:2016 has been approved by CEN as EN ISO 1:2016 without any modification.

INTERNATIONAL ISO
STANDARD 1
Third edition
2016-09-01
Geometrical product specifications
(GPS) — Standard reference
temperature for the specification
of geometrical and dimensional
properties
Spécification géométrique des produits (GPS) — Température
normale de référence pour la spécification des propriétés
géométriques et dimensionnelles
Reference number
ISO 1:2016(E)
©
ISO 2016
ISO 1:2016(E)
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

ISO 1:2016(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Terms and definitions . 1
3 Standard reference temperature value for the specification of geometrical and
dimensional properties . 1
Annex A (informative) Use of the reference temperature specification . 2
Annex B (informative) Relation to the GPS matrix model . 3
Bibliography . 4
ISO 1:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declaratio
...