EN ISO 6802:2008

SLOVENSKI STANDARD
01-maj-2009
1DGRPHãþD
SIST EN 26802:2000
*XPHQHLQSROLPHUQHFHYLWHUFHYQLSULNOMXþNLRMDþDQL]MHNOHQLPNRUGRP
+LGUDYOLþQRVXQNRYQRSUHVNXãDQMH]XSRJLEDQMHP,62
Rubber and plastics hoses and hose assemblies with wire reinforcements - Hydraulic
impulse test with flexing (ISO 6802:2005)
Tuyaux et flexibles en caoutchouc et en plastique renforcés par des fils métalliques -
Essai d'impulsions hydrauliques avec flexions (ISO 6802:2005)
Ta slovenski standard je istoveten z: EN ISO 6802:2008
ICS:
23.040.70 Gumene cevi in armature Hoses and hose assemblies
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 6802
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2008
ICS 23.040.70 Supersedes EN 26802:1993
English Version
Rubber and plastics hoses and hose assemblies with wire
reinforcements - Hydraulic impulse test with flexing (ISO
6802:2005)
Tuyaux et flexibles en caoutchouc et en plastique renforcés
par des fils métalliques - Essai d'impulsions hydrauliques
avec flexions (ISO 6802:2005)
This European Standard was approved by CEN on 29 October 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6802:2008: E
worldwide for CEN national Members.

Contents Page
Foreword.3

Foreword
The text of ISO 6802:2005 has been prepared by Technical Committee ISO/TC 45 “Rubber and rubber
products” of the International Organization for Standardization (ISO) and has been taken over as EN ISO
6802:2008 by Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assemblies” the
secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2009, and conflicting national standards shall be withdrawn at the
latest by May 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 26802:1993.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 6802:2005 has been approved by CEN as a EN ISO 6802:2008 without any modification.

INTERNATIONAL ISO
STANDARD 6802
Third edition
2005-10-01
Rubber and plastics hoses and hose
assemblies with wire reinforcements —
Hydraulic impulse test with flexing
Tuyaux et flexibles en caoutchouc et en plastique renforcés par des fils
métalliques — Essai d'impulsions hydrauliques avec flexions

Reference number
ISO 6802:2005(E)
©
ISO 2005
ISO 6802:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2005 – All rights reserved

ISO 6802:2005(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Test methods. 1
4 Apparatus . 1
5 Test piece .
...