prEN 16477-2

SLOVENSKI STANDARD
01-oktober-2012
Steklo v gradbeništvu - Poslikano steklo za interno uporabo - 2. del: Vrednotenje
skladnosti
Glass in building - Painted glass for internal use - Part 2: Evaluation of conformity
Glas im Bauwesen - Farbiges Glas für den Innenbereich - Teil 2: Konformitätsbewertung
Verre dans la construction - Verre laqué destiné à un usage à l’intérieur - Partie 2:
Évaluation de la conformité
Ta slovenski standard je istoveten z: prEN 16477-2
ICS:
81.040.20 Steklo v gradbeništvu Glass in building
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
DRAFT
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2012
ICS 81.040.20
English Version
Glass in building - Painted glass for internal use - Part 2:
Evaluation of conformity
Verre dans la construction - Verre laqué destiné à un usage Glas im Bauwesen - Farbiges Glas für den Innenbereich -
à l'intérieur - Partie 2: Évaluation de la conformité Teil 2: Konformitätsbewertung
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 129.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 16477-2:2012: E
worldwide for CEN national Members.

Contents Page
Foreword .3
1 Scope .3
2 Normative references .3
3 Terms and definitions .4
4 Requirements .4
4.1 Product description .4
4.2 Conformity with the definition of painted glass .5
4.3 Determination of the characteristic's performances.5
4.3.1 Characterisitcs of painted glass .5
4.3.2 Determination of characteristics of painted glass .6
4.4 Durability .8
4.5 Dangerous substances .9
5 Evaluation of conformity .9
5.1 General .9
5.2 Initial type testing of the product (see 5.1, 2) .9
5.2.1 General .9
5.2.2 Initial type testing of painted glass . 11
5.2.3 Initial type testing of characteristic’s performances . 12
5.3 Factory production control and inspection of samples in accordance with a prescribed
test plan (see 5.1, 1a and b) . 12
5.4 Initial inspection of factory and of factory production control (see 5.1, 1c) . 12
6 Marking and/or labelling . 14
6.1 General . 14
6.2 Product marking . 14
6.3 Product characteristics . 14
6.4 “Characteristics/performance identification paper” . 14
Annex A (normative) Factory production control . 15
Annex B (informative) Tests for ensuring conformity during factory production control . 20
Annex C (informative) Provisions for voluntary involvement of third party(ies) . 21
C.1 General . 21
C.2 Voluntary tasks for third parties . 21
C.3 Marking and labelling . 21
Annex ZA (informative) Clauses of this European Standard addressing the provisions of EU
Construction Products Directive . 22

Foreword
This document (prEN 16477-2:2012) has been prepared by Technical Committee CEN/TC 129 “Glass in
Building”, the secretariat of which is held by NBN.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
1 Scope
This European Standard covers requirements, the evaluation of conformity and the factory production control
of flat painted glass for internal use in buildings.
NOTE For glass products with electrical wiring or connections for, e.g. alarm or heating purposes, other directives,
e.g. Low Voltage Directive, may apply.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 356, Glass in Building - Security glazing - Testing and classification of resistance against manual attack
EN 410, Glass in Building - Determination of luminous and solar characteristics of glazing
EN 572–1, Glass in Building - Basic soda lime silicate glass products – Part 1: Definition and general physical
and mechanical properties
EN 572–2, Glass in Building - Basic soda lime silicate glass products – Part 2: -Float glass
EN 572-8, Glass in building – Basic soda lime silicate glass products – Part 8: supplied and final cut sizes
EN 673, Glass in Building – Determination of thermal transmittance (U value) – Calculation method
prEN 16477-1, Glass in building – Painted glass for internal use – Part 1: Requirements
EN 1063, Glass in Building - Security glazing - Testing and classification of resistance against bullet attack
EN 12600, Glass in Building - Pendulum test - Impact test method and classification for flat glass
EN 12758, Glass in Building - Glazing and airborne sound insulation – Product descriptions and determination
of properties
EN 12898, Glass in Building - Determination of the emissivity
prEN 13474 (all parts), Glass in Building - Design of glass panes
EN 13501-1:2007+A1:2009, Fire classification of construction products and building elements – Part 1:
Classification using data from reaction to fire tests
EN 13501-2:2007+A1:2009, Fire classification of construction products and building elements – Part 2:
Classification using data from resistance to fire tests excluding ventilation services
EN 13501-5:2005+A1:2009, Fire classification of construction products and building elements - Part 5:
Classification using data from external fire exposure to roofs tests
EN 13541, Glass in Building - Security glazing - Testing and classification of resistance against explosion
pressure
3 Terms and definitions
For the purposes of this document, the terms and definitions given in prEN 16477-1 and the following apply.
3.1
initial type testing
determination of the performance of a product (characteristic, durability), on the basis of either actual tests or
other procedures (such as conventional, standardised, tabulated or general accepted values, standardised or
recognised calculation methods, test reports when made available, …), in accordance with this standard that
demonstrates compliance with this standard.
3.2
test report
document that covers the results of tests undertaken on a representative sample of the product from
production or on a prototype design of the product.
3.3
product description
document that details the relevant parameters, e.g. process conditions, structure, etc., for defining a product
that complies with the standard. It includes specific reference(s) to characteristics that are modified by the
production process.
3.4
significant change
variation in performance beyond the permitted tolerance for the characteristic.
4 Requirements
4.1 Product description
For conformity purposes the painted glass manufacturer is responsible for the preparation and maintenance of
the product description. This description shall describe the product and/or product families.
Disclosure of the product description shall be at the discretion of the painted glass manufacturer or his agent
except in the case of regulatory requirements.
The description shall contain at least a normative part. The description may also contain an informative part,
when the manufacturer foresees further development of the product.
The normative part of the description shall contain the following information:
 reference to prEN 16477 Parts 1 and 2 and all other standards with which the manufacturer claims
compliance.
 materials making up the layers of the painted glass.
 glass substrates
The layers may be listed either in full, i.e. chemical composition, or by manufacturers’ code.
The substitution of materials shall maintain the conformity with the product description. The substituting
material can be added to the product description when compliance has been demonstrated.
4.2 Conformity with the definition of painted glass
Products shall conform to the definition and fulfil the requirements of painted glass as defined in prEN 16477-
1.
4.3 Determination of the characteristic's performances
4.3.1 Characteristics of painted glass
4.3.1.1 General
The characteristics of painted glass are in general those of the glass substrate (see 4.3.1.2).
4.3.1.2 Characteristics of the glass panes used for the production of painted glass
Panes shall be made of soda lime silicate float glass according to EN 572-1, EN 572-2, 572-8.
For the characteristics listed in Table 1, for the soda lime silicate glass panes, generally accepted values or
calculated values shall be used.
Since the painted glass production process does not change the majority of the characteristics of table 1
significantly they shall be used for painted glass. The characteristics that are significantly changed are the
light transmittance/reflectance and solar heat transmittance/reflectance.
Table 1 — Information on the characteristics of soda lime silicate glass panes, according to EN 572-1,
used for the production of painted glass

Characteristic Symbol Unit
ρ
- density kg/m³
- hardness HK GPa
0,1/20
- Young's modulus E
...