EN ISO 1183-1:2019

SLOVENSKI STANDARD
01-junij-2019
Nadomešča:
SIST EN ISO 1183-1:2013
Polimerni materiali - Metode za določanje gostote nepenjenih polimernih
materialov - 1. del: Metoda s potapljanjem, metoda s tekočinskim piknometrom in
titracijska metoda (ISO 1183-1:2019, popravljena različica 2019-05)
Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion
method, liquid pycnometer method and titration method (ISO 1183-1:2019, Corrected
version 2019-05)
Kunststoffe - Verfahren zur Bestimmung der Dichte von nicht verschäumten Kunststoffen
- Teil 1: Eintauchverfahren, Verfahren mit Flüssigkeitspyknometer und
Titrationsverfahren (ISO 1183-1:2019, korrigierte Fassung 2019-05)
Plastiques - Méthodes de détermination de la masse volumique des plastiques non
alvéolaires - Partie 1: Méthode par immersion, méthode du pycnomètre en milieu liquide
et méthode par titrage (ISO 1183-1:2019, Version corrigée 2019-05)
Ta slovenski standard je istoveten z: EN ISO 1183-1:2019
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 1183-1
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2019
EUROPÄISCHE NORM
ICS 83.080.01 Supersedes EN ISO 1183-1:2012
English Version
Plastics - Methods for determining the density of non-
cellular plastics - Part 1: Immersion method, liquid
pycnometer method and titration method (ISO 1183-
1:2019, Corrected version 2019-05)
Plastiques - Méthodes de détermination de la masse Kunststoffe - Verfahren zur Bestimmung der Dichte
volumique des plastiques non alvéolaires - Partie 1: von nicht verschäumten Kunststoffen - Teil 1:
Méthode par immersion, méthode du pycnomètre en Eintauchverfahren, Verfahren mit
milieu liquide et méthode par titrage (ISO 1183- Flüssigkeitspyknometer und Titrationsverfahren (ISO
1:2019) 1183-1:2019)
This European Standard was approved by CEN on 7 March 2019.

This European Standard was corrected and reissued by the CEN-CENELEC Management Centre on 24 July 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATIO N

EUROPÄISCHES KOMITEE FÜR NORMUN G

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1183-1:2019 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 1183-1:2019) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2019, and conflicting national standards shall
be withdrawn at the latest by October 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 1183-1:2012.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 1183-1:2019, Corrected version 2019-05 has been approved by CEN as EN ISO 1183-
1:2019 without any modification.

INTERNATIONAL ISO
STANDARD 1183-1
Third edition
2019-03
Corrected version
2019-05
Plastics — Methods for determining
the density of non-cellular plastics —
Part 1:
Immersion method, liquid pycnometer
method and titration method
Plastiques — Méthodes de détermination de la masse volumique des
plastiques non alvéolaires —
Partie 1: Méthode par immersion, méthode du pycnomètre en milieu
liquide et méthode par titrage
Reference number
ISO 1183-1:2019(E)
©
ISO 2019
ISO 1183-1:2019(E)
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

ISO 1183-1:2019(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Conditioning . 2
5 Methods . 2
5.1 Method A — Immersion method . 2
5.1.1 Apparatus . 2
5.1.2 Immersion liquid . 3
5.1.3 Specimens . 3
5.1.4 Procedure . 3
5.2 Method B — Liquid pycnometer method. 4
5.2.1 Apparatus . 4
5.2.2 Immersion liquid . 5
5.2.3 Specimens . 5
5.2.4 Procedure . 5
5.3 Method C — Titration method . 6
5.3.1 Apparatus . 6
5.3.2 Immersion liquids . 6
5.3.3 Specimens . 6
5.3.4 Procedure . 6
6 Correction for buoyancy in air . 7
7 Test report . 8
Annex A (informative) Liquid systems suitable for use in Method C . 9
Annex B (informative) Correction for buoyancy in air .10
Bibliography .12
ISO 1183-1:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 5, Physical-
chemical properties.
This third edition cancels and replaces the second edition (ISO 1183-1:2012), which has been technically
revised. The main changes compared to the previous edition are as follows:
— the buoyancy correction has been revised.
A list of all parts in the ISO 1183 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
This corrected version of ISO 1183-1:2019 incorporates the following corrections:
— correction of the definition of Formula (2).
iv © ISO 2019 – All rights reserved

INTERNATIONAL STANDARD ISO 1183-1:2019(E)
Plastics — Methods for determining the density of non-
cellular plastics —
Part 1:
Immersion method, liquid pycnometer method and
titration method
WARNING — The use of this document might involve hazardous materials, operations or
equipment. This document does not purport to address all of the safety problems, if any,
associated with its use. It is the responsibility of the user of this document to establish
appropriate health and safety practices.
1 Scope
This document specifies three methods for the determination of the density of non-cellular plastics in
the form of void-free moulded or extruded objects, as well as powders, flakes and granules.
— Method A: Immersion method, for solid plastics (except for powders) in void-free form.
— Method B: Liquid pycnometer method, for particles, powders, flakes, granules or small pieces of
finished parts.
— Method C: Titration method, for plastics in any void-free form.
NOTE Density is frequently used to follow variations in physical structure or composition of plastic
materials. Density can also be useful in assessing the uniformity of samples or specimens. Often, the density of
plastic materials depend upon the choice of specimen preparation method. When this is the case, precise details
of the specimen preparation method are intended to be included in the appropriate material specification. This
note is applicable to all three methods.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 291, Plastics — Standard atmospheres for conditioning and testing
ISO 472, Plastics — Vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 472 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https: //www .iso .org/obp
— IEC Electropedia: available at http: //www .electropedia .org/
ISO 1183-1:2019(E)
3.1
mass
m
quantity of matter contained in a body
Note 1 to entry: It is expressed in kilograms (kg) or grams (g).
3.2
apparent mass
m
APP
mass of a body obtained by measuring its weight using an appropriately calibrated balance
Note 1 to entry: It is expressed in kilograms (kg) or grams (g).
3.3
density
ρ
3 3
ratio of the mass m of a sample to its volume V (at the temperature T), expressed in kg/m , kg/dm (g/
3)
cm or kg/l (g/ml)
[1]
Note 1 to entry: The following terms, based upon ISO 80000-4 , are given in Table 1 for clarification.
Table 1 — Density terms
Term Symbol Formulation Units
kg/m
3 3
Density ρ m/V kg/dm (g/cm )
kg/l (g/ml)
m /kg
3 3
Specific volume v V/m (= 1/ρ) dm /kg (cm /g)
l/kg (ml/g)
4 Conditioning
The test atmosphere shall be in accordance with ISO 291. In general, conditioning specimens to constant
temperature is not required, because the determination itself brings the specimen to the constant
te
...