EN ISO 11960:2001

SLOVENSKI STANDARD
SIST EN ISO 11960:2004
01-maj-2004
1DGRPHãþD
SIST EN ISO 11960:2001
Petroleum and natural gas industries - Steel pipes for use as casing or tubing for
wells (ISO 11960:2001)
Petroleum and natural gas industries - Steel pipes for use as casing or tubing for wells
(ISO 11960:2001)
Erdöl- und Erdgasindustrie - Stahlrohre zur Verwendung als Futter- oder Steigrohre für
Bohrungen (ISO 11960:2001)
Industries du pétrole et du gaz naturel - Tubes d'acier utilisés comme cuvelage ou tubes
de production dans les puits (ISO 11960:2001)
Ta slovenski standard je istoveten z: EN ISO 11960:2001
ICS:
75.180.10 Oprema za raziskovanje in Exploratory and extraction
odkopavanje equipment
77.140.75 Jeklene cevi in cevni profili Steel pipes and tubes for
za posebne namene specific use
SIST EN ISO 11960:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 11960:2004

---------------------- Page: 2 ----------------------

SIST EN ISO 11960:2004

---------------------- Page: 3 ----------------------

SIST EN ISO 11960:2004

---------------------- Page: 4 ----------------------

SIST EN ISO 11960:2004
INTERNATIONAL ISO
STANDARD 11960
Second edition
2001-10-01
Petroleum and natural gas industries —
Steel pipes for use as casing or tubing for
wells
Industries du pétrole et du gaz naturel — Tubes d'acier utilisés comme
cuvelage ou tubes de production dans les puits
Reference number
ISO 11960:2001(E)
©
ISO 2001

---------------------- Page: 5 ----------------------

SIST EN ISO 11960:2004
ISO 11960:2001(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2001
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2001 – All rights reserved

---------------------- Page: 6 ----------------------

SIST EN ISO 11960:2004
ISO 11960:2001(E)
Contents Page
Foreword.vi
Introduction.vii
1 Scope .1
2 Conformance.2
2.1 Normative references .2
2.2 Units of measurement .2
2.3 Tables and figures .2
3 Normative references .2
4 Terms, definitions, symbols and abbreviated terms.4
4.1 Terms and definitions .4
4.2 Symbols and abbreviated terms .8
5 Information to be supplied by the purchaser .9
5.1 Casing .9
5.2 Tubing.10
6 Process of manufacture.12
6.1 General.12
6.2 Heat treatment.12
6.3 Straightening.13
6.4 Traceability.13
7 Material requirements .14
7.1 Chemical composition .14
7.2 Tensile properties.14
7.3 Charpy V-notch test properties — General requirements.15
7.4 Charpy V-notch (CVN) — Absorbed energy requirements for coupling stock, coupling blanks
and couplings.16
7.5 Charpy V-notch — Absorbed energy requirements for pipe .17
7.6 Charpy V-notch test — Absorbed energy requirements for casing and tubing accessories.19
7.7 Hardness maxima .20
7.8 Hardness variation — Grades C90, T95 and Q125 .20
7.9 Process control — Grades C90, T95 and Q125 .20
7.10 Hardenability — Minimum percentage martensite for quenched and tempered products.21
7.11 Grain size — Grades C90 and T95 .21
7.12 Surface condition — Grades L80 9Cr and L80 13Cr .21
7.13 Flattening — Electric-welded pipe .21
7.14 Sulfide stress corrosion cracking (SSCC) test — Grades C90 and T95 .21
8 Dimensions, masses, tolerances, pipe ends and defects .23
8.1 Labels and sizes .23
8.2 Dimensions and masses.23
8.3 Diameter.23
8.4 Wall thickness.24
8.5 Mass.24
8.6 Length.24
8.7 Casing jointers.24
8.8 Height and trim of electric-weld flash.24
8.9 Straightness .25
8.10 Drift requirements.25
8.11 Tolerances on dimensions and masses.26
8.12 Pipe ends.27
© ISO 2001 – All rights reserved iii

---------------------- Page: 7 ----------------------

SIST EN ISO 11960:2004
ISO 11960:2001(E)
8.13 Defects .28
8.14 Coupling make-up and thread protection .29
9 Couplings.29
9.1 General requirements.29
9.2 Alternative grades or heat treatments .29
9.3 Process of manufacture — Groups 1, 2 and 3.30
9.4 Process of manufacture — Grade Q125.30
9.5 Mechanical properties.30
9.6 Dimensions and tolerances .31
9.7 Regular couplings.31
9.8 Special-clearance couplings — Groups 1, 2 and 3 .31
9.9 Combination couplings.31
9.10 Reducing couplings.31
9.11 Seal-ring couplings.31
9.12 Special-bevel couplings — Groups 1, 2 and 3.32
9.13 Threading.32
9.14 Surface inspection.32
9.15 Measurement of imperfections.33
9.16 Repair and removal of imperfections and defects .33
9.17 Thread surface treatment — Grade Q125.33
9.18 Couplings and coupling blank protection — Grade Q125.33
10 Inspection and testing.33
10.1 Test equipment .33
10.2 Lot definition for testing of mechanical properties.34
10.3 Testing of chemical composition.34
10.4 Tensile tests .35
10.5 Flattening test .37
10.6 Hardness test .38
10.7 Impact test .41
10.8 Grain size determination — Grades C90 and T95 .43
10.9 Hardenability — Grades C90 and T95.43
10.10 Sulfide stress cracking test — Grades C90 and T95.43
10.11 Metallographic evaluation — EW Grades P110 and Q125.43
10.12 Hydrostatic test.43
10.13 Dimensional testing.45
10.14 Visual inspection .47
10.15 Non-destructive examination (NDE) .48
11 Marking .53
11.1 General.53
11.2 Stamp marking requirements .54
11.3 Stencil marking requirements .55
11.4 Colour identification .55
11.5 Thread and end-finish marking — All groups.56
11.6 Pipe-threader marking requirements — All groups .56
12 Coating and protection.57
12.1 Coatings — All groups .57
12.2 Thread protectors .57
13 Documents.58
13.1 Electronic media — All groups.58
13.2 Certification — Groups 1, 2 and 3 .58
13.3 Certification requirements — Grade Q125 .58
13.4 Retention of records.58
14 Minimum facility requirements for various categories of manufacturer .58
14.1 Pipe mill .58
14.2 Processor.59
14.3 Threader.59
14.4 Coupling, pup-joint, and accessory manufacturer.59
iv © ISO 2001 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 11960:2004
ISO 11960:2001(E)
Annex A (normative) Supplementary requirements.60
Annex B (normative) Purchaser inspection .72
Annex C (normative) Tables in SI units .73
Annex D (normative) Figures in SI (USC) units.136
Annex E (normative) Tables in USC units .158
Annex F (informative) Marking instructions for API licensees.217
Annex G (informative) Procedures used to convert from USC units to SI units .221
Bibliography.234
© ISO 2001 – All rights reserved v

---------------------- Page: 9 ----------------------

SIST EN ISO 11960:2004
ISO 11960:2001(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 11960 was prepared by Technical Committee ISO/TC 67, Materials, equipment and
offshore structures for petroleum and natural gas industries, Subcommittee SC 5, Casing, tubing and drill pipe.
This second edition replaces the first edition (ISO 11960:1996) which has been technically revised. It is the intent of
TC 67 that the first and second editions of ISO 11960 both be applicable, at the user's option, for a period of six
months after the date of publication of this second edition, after which the first edition will no longer be applicable.
Annexes A to E form a normative part of this International Standard. Annexes F and G are for information only.
vi © ISO 2001 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 11960:2004
ISO 11960:2001(E)
Introduction
This International Standard is based on API 5CT (Specification for Casing and Tubing).
Users of this International Standard should be aware that further or differing requirements may be needed for
individual applications. This International Standard is not intended to inhibit a vendor from offering, or the purchaser
from accepting, alternative equipment or engineering solutions for the individual application. This may be
particularly applicable where there is innovative or developing technology. Where an alternative is offered, the
vendor should identify any variations from this International Standard and provide details.
This International Standard includes requirements of various nature. These are identified by the use of certain
verbal forms:
� SHALL is used to indicate that a provision is MANDATORY;
� SHOULD is used to indicate that a provision is not mandatory, but RECOMMENDED as good practice;
� MAYis usedto indicatethat aprovision is OPTIONAL.
© ISO 2001 – All rights reserved vii

---------------------- Page: 11 ----------------------

SIST EN ISO 11960:2004

---------------------- Page: 12 ----------------------

SIST EN ISO 11960:2004
INTERNATIONAL STANDARD ISO 11960:2001(E)
Petroleum and natural gas industries — Steel pipes for use as
casing or tubing for wells
1 Scope
1.1 This International Standard specifies the technical delivery conditions for steel pipes (casing, tubing, plain
end casing liners and pup-joints) and accessories. This International Standard is applicable to the following
connections in accordance with ISO 10422 or API Spec 5B:
� short round thread casing (STC);
� long round thread casing (LC);
� buttress thread casing (BC);
� extreme-line casing (XC);
� non-upset tubing (NU);
� external upset tubing (EU);
� integral joint tubing (IJ).
For such connections, this International Standard specifies the technical delivery conditions for couplings and
thread protection.
For pipes covered by this International Standard, the sizes, masses, wall thicknesses, grades and applicable end
finishes are defined.
This International Standard may also be applied to tubulars with connections not covered by ISO/API standards.
1.2 The four groups of products to which this International Standard is applicable include the following grades of
pipe:
� Group 1: All casing and tubing in Grades H, J, K and N;
� Group 2: All casing and tubing in Grades C, L, M and T;
� Group 3: All casing and tubing in Grade P;
� Group 4: All casing in Grade Q.
1.3 Casing sizes larger than Label 1: 4-1/2 but smaller than Label 1: 10-3/4 may be specified by the purchaser to
be used in tubing service, see Tables C.1, C.24, C.30 and C.31 or Tables E.1, E.24, E.30 and E.31.
1.4 Supplementary requirements that may optionally be agreed between purchaser and manufacturer, for non-
destructive examination, coupling blanks, upset casing, electric-welded casing, impact testing, seal ring couplings
and certificates are given in annex A.
1.5 This International Standard is not applicable to threading requirements.
NOTE Dimensional requirements on threads and thread gauges, stipulations on gauging practice, gauge specifications, as
well as instruments and methods for inspection of threads are given in ISO 10422 or API Spec 5B. Connections machined to
either of these specifications are the same for practical purposes and are totally interchangeable.
© ISO 2001 – All rights reserved 1

---------------------- Page: 13 ----------------------

SIST EN ISO 11960:2004
ISO 11960:2001(E)
2 Conformance
2.1 Normative references
In the interests of worldwide application of this International Standard, ISO/TC 67 has decided, after detailed
technical analysis, that certain of the normative documents listed in clause 3 and prepared by ISO/TC 67 or other
ISO Technical Committee are interchangeable in the context of the relevant requirement with the relevant
document prepared by the American Petroleum Institute (API), the American Society for Testing and Materials
(ASTM) or the American National Standards Institute (ANSI). These latter documents are cited in the running text
following the ISO reference and preceded by “or”, for example “ISO XXXX or API YYYY”. Application of an
alternative normative document cited in this manner will lead to the same results as the use of the preceding
ISO reference. These documents are thus considered interchangeable in practice.
2.2 Units of measurement
In this International Standard, data are expressed in both the International System (SI) of units and the United
States Customary (USC) system of units. For a specific order item, it is intended that only one system of units be
used, without combining data expressed in the other system.
Products manufactured to specifications expressed in either of these unit systems shall be considered equivalent
and totally interchangeable. Consequently, compliance with the requirements of this International Standard as
expressed in one system provides compliance with requirements expressed in the other system.
For data expressed in the SI, a comma is used as the decimal separator and a space as the thousands separator.
For data expressed in the USC system, a dot (on the line) is used as the decimal separator and a space as the
thousands separator.
In the text, data in SI units are followed by data in USC units in brackets.
2.3 Tables and figures
Separate tables for data expressed in SI units and USC units are given in annex C and annex E respectively. For a
specific order item, only one unit system shall be used.
Figures are contained in annex D and express data in both SI and USC units.
3 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.
ISO 31-0, Quantities and units — Part 0: General principles
ISO 643, Steels — Micrographic determination of the ferritic or austenitic grain size
ISO 6506-1, Metallic materials — Brinell Hardness test — Part 1:Test method
ISO 6508-1, Metallic materials — Rockwell Hardness test —Part 1:Test method (Scales A, B,C,D, E,F,G, H, K,
N, T
ISO 6892, Metallic materials — Tensile testing at ambient temperature
2 © ISO 2001 – All rights reserved

---------------------- Page: 14 ----------------------

SIST EN ISO 11960:2004
ISO 11960:2001(E)
ISO 7500-1, Metallic materials — Verification of static uniaxial testing machines — Part 1: Tensile/compression
testing machines — Verification and calibration of the force-measuring system
ISO 9303, Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes — Full
peripheral ultra
...