ASTM D3265-17e1
(Test Method)Standard Test Method for Carbon Black—Tint Strength
Standard Test Method for Carbon Black—Tint Strength
SIGNIFICANCE AND USE
4.1 For the broad range of commercial rubber grade carbon blacks, tint strength is highly dependent upon particle size. Tint strength can be used as an indication of particle size; however, tint strength is also dependent on structure and aggregate size distribution. Therefore, differences in tint strength within grades of carbon black may reflect differences other than particle size.
Note 1: This test method was developed primarily for the characterization of N100, N200, and N300 series carbon blacks.
4.2 Tint strength values within the carbon black industry have been developed using a Automatic Muller apparatus which is used to prepare carbon black-zinc oxide pastes. A new mixing apparatus, SpeedMixer4 (DAC 150 FVZ), and a corresponding procedure have been extensively studied within D24 and shown to provide equivalent tint strength for all carcass or soft blacks and most tread blacks with the exception of higher surface area N100 types and specialty blacks. Therefore, it is the responsibility of the user of this alternate apparatus to ensure their products will adequately disperse. Disputes arising between a user and producer should be resolved using the Automatic Muller apparatus until ASTM develops adequate precision statements.
4.3 The term ITRB is used in the entire text for both, the original ITRB, used as the first reference material for tint testing, but which is now used up, and the successor reference material, ITRB2. Wherever required, like in calculations where it is crucial to differentiate between the original ITRB and ITRB2, this will be clearly mentioned in the text of the test procedure.
SCOPE
1.1 This test method covers the determination of the tint strength of carbon black relative to an industry tint reference black (ITRB).
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation: D3265 − 17
Standard Test Method for
1
Carbon Black—Tint Strength
This standard is issued under the fixed designation D3265; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Editorially corrected footnote 15 in August 2017.
1. Scope 3. Summary of Test Method
3.1 A carbon black sample is mixed with a white powder
1.1 This test method covers the determination of the tint
(zincoxide)andaliquidvehicle(epoxidizedsoybeanoil,ESO)
strength of carbon black relative to an industry tint reference
to produce a black or gray paste. This paste is then spread to
black (ITRB).
produce a surface suitable for measuring the reflectance of the
1.2 The values stated in SI units are to be regarded as the
mixture by means of a photo-electric reflectance meter. The
standard. The values given in parentheses are for information
reflectance of the tested sample is then compared to the
only.
reflectance of the ITRB prepared in the same manner. The tint
strength of the tested sample is expressed as units of the
1.3 This standard does not purport to address all of the
reflectance of the ITRB divided by the reflectance of the
safety concerns, if any, associated with its use. It is the
sample and multiplied by 100.
responsibility of the user of this standard to establish appro-
priate safety, health and environmental practices and deter-
3.2 Correction Factor:
mine the applicability of regulatory limitations prior to use.
3.2.1 When ITRB-2, Paraplex G-62 (made before June
1.4 This international standard was developed in accor-
2012) and ZnO lot#8 are used, apply a correction factor of
dance with internationally recognized principles on standard-
1.0134 for the calibration and standardization in Section 8.
ization established in the Decision on Principles for the
3.2.2 There should be no correction applied when ITRB is
Development of International Standards, Guides and Recom-
used with Paraplex G-62 and ZnO Lot#8 or earlier, that is, the
mendations issued by the World Trade Organization Technical
correction factor is “1”.
Barriers to Trade (TBT) Committee.
3.2.3 There should be no correction applied in the calcula-
tion in Section 10 when using the currently available tint raw
2. Referenced Documents materials (see Section 6) for pastes prepared with either ITRB
3
or ITRB2, that is, the correction factor is “1”.
2
2.1 ASTM Standards:
D1799 Practice for Carbon Black—Sampling Packaged
4. Significance and Use
Shipments
4.1 For the broad range of commercial rubber grade carbon
D1900 Practice for Carbon Black—Sampling Bulk Ship-
blacks,tintstrengthishighlydependentuponparticlesize.Tint
ments
strength can be used as an indication of particle size; however,
D4483 Practice for Evaluating Precision for Test Method
tint strength is also dependent on structure and aggregate size
Standards in the Rubber and Carbon Black Manufacturing
Industries
D4821 Guide for Carbon Black—Validation of Test Method
Precision and Bias
3
In 2013 issues were reported when using Paraplex G-62 purchased after June
2012 and ZnO Lot#10. An ASTM task group investigated the issues and found the
following raw materials acceptable for Tint testing:
1) ESO: Paraplex G-62 purchased before June 2012 or currently available
1
This test method is under the jurisdiction ofASTM Committee D24 on Carbon GreenChem Greenflex 7170, lot 590911X24, and
Black and is the direct responsibility of Subcommittee D24.21 on Carbon Black 2) zinc oxide Lot#8 or earlier, and currently available ZnO lot#11.
Surface Area and Related Properties. Itishighlyrecommendedtoonlyusetheserawmaterialsidentifiedasacceptable
Current edition approved May 1, 2017. Published May 2017. Originally asothersourcesmayleadtounacceptabledifferencesinthetestresults.Thetinttask
approved in 1973. Last previous edition approved in 2015 as D3265 – 15a. DOI: group has determined that Paraplex G-62 with lot numbers that begin with the digit
10.1520/D3265-17E01. 5 and zinc oxide lots 9 and 10 are suspect and may not give acceptable results.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or When using the new raw materials for tint testing some differences may be
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM observedwithvariousgradesofcarbonblackcomparedwithhistoricaldata.Forthis
Standards volume information, refer to the standard’s Document Summary page on reason it is the responsibility of the manufacturer to identify any such differences,
the ASTM website. and if necessary, revise any specifications between producer and user.
Copyright © ASTM International, 10
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: D3265 − 17 D3265 − 17
Standard Test Method for
1
Carbon Black—Tint Strength
This standard is issued under the fixed designation D3265; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Editorially corrected footnote 15 in August 2017.
1. Scope
1.1 This test method covers the determination of the tint strength of carbon black relative to an industry tint reference black
(ITRB).
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D1799 Practice for Carbon Black—Sampling Packaged Shipments
D1900 Practice for Carbon Black—Sampling Bulk Shipments
D4483 Practice for Evaluating Precision for Test Method Standards in the Rubber and Carbon Black Manufacturing Industries
D4821 Guide for Carbon Black—Validation of Test Method Precision and Bias
3. Summary of Test Method
3.1 A carbon black sample is mixed with a white powder (zinc oxide) and a liquid vehicle (epoxidized soybean oil, ESO) to
produce a black or gray paste. This paste is then spread to produce a surface suitable for measuring the reflectance of the mixture
by means of a photo-electric reflectance meter. The reflectance of the tested sample is then compared to the reflectance of the ITRB
prepared in the same manner. The tint strength of the tested sample is expressed as units of the reflectance of the ITRB divided
by the reflectance of the sample and multiplied by 100.
3.2 Correction Factor:
3.2.1 When ITRB-2, Paraplex G-62 (made before June 2012) and ZnO lot#8 are used, apply a correction factor of 1.0134 for
the calibration and standardization in Section 8.
3.2.2 There should be no correction applied when ITRB is used with Paraplex G-62 and ZnO Lot#8 or earlier, that is, the
correction factor is “1”.
1
This test method is under the jurisdiction of ASTM Committee D24 on Carbon Black and is the direct responsibility of Subcommittee D24.21 on Carbon Black Surface
Area and Related Properties.
Current edition approved May 1, 2017. Published May 2017. Originally approved in 1973. Last previous edition approved in 2015 as D3265 – 15a. DOI:
10.1520/D3265-17.10.1520/D3265-17E01.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
´1
D3265 − 17
3.2.3 There should be no correction applied in the calculation in Section 10 when using the currently available tint raw materials
3
(see Section 6) for pastes prepared with either ITRB or ITRB2, that is, the correction factor is “1”.
4. Significance and Use
4.1 For the broad range of commercial rubber grade carbon blacks, tint strength is highly dependent upon particle size. Tint
strength can be used as an indication of particle size; however, tint strength is also dependent on structure and aggregate size
distribution. Therefore, differences in tint strength within grades of carbon black may reflect differences other than particle size.
NOTE 1—This test method was developed primarily for the characterization of N100, N200, and N300 series carbon blacks.
4.2 Tint strength values within the carbon black industry have been developed using a Automatic Muller apparatus which is used
4
to prepare carbon black-zinc oxide pastes. A new mixing apparatus, SpeedMixer (DAC 150 FVZ), and a corresponding procedure
have been extensi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.