ASTM D6353-23

ASTM D6353-23 is a guide published by ASTM International. Its full title is "Standard Guide for Sampling Plan and Core Sampling for Prebaked Anodes Used in Aluminum Production". This standard covers: SIGNIFICANCE AND USE 4.1 Core sampling is an acceptable way of obtaining a test specimen without destroying the usefulness of an anode block. 4.1.1 Test specimen obtained by this guide can be used by producers and users of carbon anodes for the purpose of conducting the tests in Note 1 to obtain comparative physical properties. 4.2 Sampling shall not weaken the anode or increase the likelihood of premature failure. SCOPE 1.1 This guide covers sampling for prebaked carbon anodes used in the production of aluminum, and details procedures for taking test samples from anode blocks. It covers equipment and procedures for obtaining samples from anode blocks in a manner that does not destroy the block or prevent its subsequent use as originally intended. However, the user must determine the subsequent use of the sampled anode blocks. Preferred locations for taking samples from single units of anodes are covered in this guide. 1.1.1 Information for sampling of shaped refractory products, in general, is given in ISO 5022. This standard details the statistical basis for sampling plans for acceptance testing of a consignment or lot. Anodes used in the production of aluminum have specific requirements for sampling and while the statistical basis for sampling given in ISO 5022 applies, further or modified requirements may also apply. 1.1.2 Information for sampling of anodes for Al-metal production is given in ISO 8007-2. This standard details the statistical basis for sampling plans for acceptance testing of a consignment or lot. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. Note 1: The following ASTM standards are noted as sources of useful information: Test Methods D5502, D6120, D6744, and D6745. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE 4.1 Core sampling is an acceptable way of obtaining a test specimen without destroying the usefulness of an anode block. 4.1.1 Test specimen obtained by this guide can be used by producers and users of carbon anodes for the purpose of conducting the tests in Note 1 to obtain comparative physical properties. 4.2 Sampling shall not weaken the anode or increase the likelihood of premature failure. SCOPE 1.1 This guide covers sampling for prebaked carbon anodes used in the production of aluminum, and details procedures for taking test samples from anode blocks. It covers equipment and procedures for obtaining samples from anode blocks in a manner that does not destroy the block or prevent its subsequent use as originally intended. However, the user must determine the subsequent use of the sampled anode blocks. Preferred locations for taking samples from single units of anodes are covered in this guide. 1.1.1 Information for sampling of shaped refractory products, in general, is given in ISO 5022. This standard details the statistical basis for sampling plans for acceptance testing of a consignment or lot. Anodes used in the production of aluminum have specific requirements for sampling and while the statistical basis for sampling given in ISO 5022 applies, further or modified requirements may also apply. 1.1.2 Information for sampling of anodes for Al-metal production is given in ISO 8007-2. This standard details the statistical basis for sampling plans for acceptance testing of a consignment or lot. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. Note 1: The following ASTM standards are noted as sources of useful information: Test Methods D5502, D6120, D6744, and D6745. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D6353-23 is classified under the following ICS (International Classification for Standards) categories: 77.020 - Production of metals. The ICS classification helps identify the subject area and facilitates finding related standards.

ASTM D6353-23 has the following relationships with other standards: It is inter standard links to ASTM D4175-23a, ASTM D6744-23, ASTM D4175-23e1, ASTM D6744-06(2017)e1, ASTM D6120-97(2017)e1, ASTM D6120-97(2012), ASTM D6745-11, ASTM D6745-06(2011), ASTM D6744-06(2011)e1, ASTM D6744-06(2011), ASTM D5502-00(2010), ASTM D6120-97(2007), ASTM D6745-06, ASTM D6744-06, ASTM D5502-00(2005). Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

ASTM D6353-23 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.