iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D2359-12

(Specification)

Standard Specification for Refined Benzene-535

Standard Specification for Refined Benzene-535

ABSTRACT
This specification covers a grade of benzene known as refined benzene-535. Different tests shall be performed in order to determine the following properties of refined benzene-535: minimum purity, maximum toluene content, maximum sulfur content, maximum thiophene content, maximum nonaromatic hydrocarbon content, maximum nitrogen content, water content, maximum acid wash color, appearance, maximum color, 1,4 dioxane content, and minimum solidification point with anhydrous basis.
SCOPE
1.1 This specification covers a grade of benzene known as refined benzene-535.  
1.2 The following applies to all specified limits in this standard: for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 Consult current OSHA regulations, supplier's Material Safety Data Sheets, and local regulations for all materials used in this specification.

General Information

Status
Historical
Publication Date
31-Oct-2012
ICS
87.060.30 - Solvents
Technical Committee
D16 - Aromatic, Industrial, Specialty and Related Chemicals
Drafting Committee
D16.01 - Benzene, Toluene, Xylenes, Cyclohexane and Their Derivatives
Current Stage
Ref Project

Relations

Replaces
ASTM D2359-10 - Standard Specification for Refined Benzene-535
Effective Date
01-Nov-2012
Replaced By
ASTM D2359-16 - Standard Specification for Refined Benzene-535
Effective Date
01-Jun-2016
Referred By
ASTM D4790-23 - Standard Terminology of Aromatic Hydrocarbons and Related Chemicals
Effective Date
01-Nov-2012
Referred By
ASTM D4735-19 - Standard Test Method for Determination of Trace Thiophene in Refined Benzene by Gas Chromatography
Effective Date
01-Nov-2012
Referred By
ASTM D7011-15(2019) - Standard Test Method for Determination of Trace Thiophene in Refined Benzene by Gas Chromatography and Sulfur Selective Detection
Effective Date
01-Nov-2012

Buy Standard

ASTM D2359-12 - Standard Specification for Refined Benzene-535ASTM D2359-12 - Standard Specification for Refined Benzene-535
PreviousNext
Technical specification
ASTM D2359-12 - Standard Specification for Refined Benzene-535
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM D2359-12 - Standard Specification for Refined Benzene-535REDLINE ASTM D2359-12 - Standard Specification for Refined Benzene-535
PreviousNext
Technical specification
REDLINE ASTM D2359-12 - Standard Specification for Refined Benzene-535
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D2359 −12
StandardSpecification for
1
Refined Benzene-535
This standard is issued under the fixed designation D2359; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* D5194 Test Method for Trace Chloride in Liquid Aromatic
Hydrocarbons
1.1 This specification covers a grade of benzene known as
D5386 Test Method for Color of Liquids Using Tristimulus
refined benzene-535.
Colorimetry
1.2 The following applies to all specified limits in this
D5808 Test Method for Determining Chloride in Aromatic
standard: for purposes of determining conformance with this
Hydrocarbons and Related Chemicals by Microcoulom-
standard, an observed value or a calculated value shall be
etry
rounded off “to the nearest unit” in the last right-hand digit
D6069 Test Method for Trace Nitrogen in Aromatic Hydro-
used in expressing the specification limit, in accordance with
carbons by Oxidative Combustion and Reduced Pressure
the rounding-off method of Practice E29.
Chemiluminescence Detection
1.3 The values stated in SI units are to be regarded as
D6304 Test Method for Determination of Water in Petro-
standard. No other units of measurement are included in this
leum Products, Lubricating Oils, and Additives by Cou-
standard.
lometric Karl Fischer Titration
1.4 Consult current OSHA regulations, supplier’s Material D6875 Test Method for Solidification Point of Industrial
Safety Data Sheets, and local regulations for all materials used
Organic Chemicals by Thermistor
in this specification.
D7011 Test Method for Determination of Trace Thiophene
in Refined Benzene by Gas Chromatography and Sulfur
2. Referenced Documents
Selective Detection
2
2.1 ASTM Standards:
D7183 Test Method for Determination of Total Sulfur in
D848 Test Method for Acid Wash Color of Industrial Aro-
Aromatic Hydrocarbons and Related Chemicals by Ultra-
matic Hydrocarbons
violet Fluorescence
D852 Test Method for Solidification Point of Benzene
D7184 Test Method for Ultra Low Nitrogen in Aromatic
D1209 Test Method for Color of Clear Liquids (Platinum-
Hydrocarbons by Oxidative Combustion and Reduced
Cobalt Scale)
Pressure Chemiluminescence Detection
D1685 Test Method for Traces of Thiophene in Benzene by
D7359 Test Method for Total Fluorine, Chlorine and Sulfur
3
Spectrophotometry (Withdrawn 2009)
in Aromatic Hydrocarbons and Their Mixtures by Oxida-
D3437 Practice for Sampling and Handling Liquid Cyclic
tive Pyrohydrolytic Combustion followed by Ion Chroma-
Products
tography Detection (Combustion Ion Chromatography-
D4492 Test Method for Analysis of Benzene by Gas Chro-
CIC)
matography
D7360 Test Method for Analysis of Benzene by Gas Chro-
D4735 Test Method for Determination of Trace Thiophene
matography with External Calibration
in Refined Benzene by Gas Chromatography
D7375 Test Method for Trace Quantities of Water in Aro-
matic Hydrocarbons and Their Mixtures by Coulometric
1
This specification is under the jurisdiction of ASTM Committee D16 on
Karl Fischer Titration
Aromatic Hydrocarbons and Related Chemicals and is the direct responsibility of
D7457 Test Method for Determining Chloride in Aromatic
Subcommittee D16.01 on Benzene, Toluene, Xylenes, Cyclohexane and Their
Hydrocarbons and Related Chemicals by Microcoulom-
Derivatives.
Current edition approved Nov. 1, 2012. Published December 2012. Originally
etry
approved in 1966. Last previous edition approved in 2010 as D2359 – 10. DOI:
D7504 Test Method for Trace Impurities in Monocyclic
10.1520/D2359-12.
2 Aromatic Hydrocarbons by Gas Chromatography and
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Effective Carbon Number
Standards volume information, refer to the standard’s Document Summary page on
D7536 Test Method for Chlorine in Aromatics by Mono-
the ASTM website.
3 chromatic Wavelength Dispersive X-ray Fluorescence
The last approved version of this historical standard is referenced on
www.astm.org. Spectrometry
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D2359 − 12
E29 Practice for Using Significant Digits in Test Data to
A
If more than one method is listed, the producer and user should agree on the
Determine Conformance with Specifications
referee method.
E1064 Test Method for Water in Organic Liquids by Coulo-
B
Clear liquid free of sediment and haze when observed at 18.3 to 25.6°C.
metric Karl Fischer
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D2359 − 10 D2359 − 12
Standard Specification for
1
Refined Benzene-535
This standard is issued under the fixed designation D2359; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers a grade of benzene known as refined benzene-535.
1.2 The following applies to all specified limits in this standard: for purposes of determining conformance with this standard,
an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing
the specification limit, in accordance with the rounding-off method of Practice E29.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 Consult current OSHA regulations, supplier’s Material Safety Data Sheets, and local regulations for all materials used in
this specification.
2. Referenced Documents
2
2.1 ASTM Standards:
D848 Test Method for Acid Wash Color of Industrial Aromatic Hydrocarbons
D852 Test Method for Solidification Point of Benzene
D1209 Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)
3
D1685 Test Method for Traces of Thiophene in Benzene by Spectrophotometry (Withdrawn 2009)
D3437 Practice for Sampling and Handling Liquid Cyclic Products
D4492 Test Method for Analysis of Benzene by Gas Chromatography
D4735 Test Method for Determination of Trace Thiophene in Refined Benzene by Gas Chromatography
D5194 Test Method for Trace Chloride in Liquid Aromatic Hydrocarbons
D5386 Test Method for Color of Liquids Using Tristimulus Colorimetry
D5808 Test Method for Determining Chloride in Aromatic Hydrocarbons and Related Chemicals by Microcoulometry
D6069 Test Method for Trace Nitrogen in Aromatic Hydrocarbons by Oxidative Combustion and Reduced Pressure
Chemiluminescence Detection
D6304 Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl
Fischer Titration
D6875 Test Method for Solidification Point of Industrial Organic Chemicals by Thermistor
D7011 Test Method for Determination of Trace Thiophene in Refined Benzene by Gas Chromatography and Sulfur Selective
Detection
D7183 Test Method for Determination of Total Sulfur in Aromatic Hydrocarbons and Related Chemicals by Ultraviolet
Fluorescence
D7184 Test Method for Ultra Low Nitrogen in Aromatic Hydrocarbons by Oxidative Combustion and Reduced Pressure
Chemiluminescence Detection
D7359 Test Method for Total Fluorine, Chlorine and Sulfur in Aromatic Hydrocarbons and Their Mixtures by Oxidative
Pyrohydrolytic Combustion followed by Ion Chromatography Detection (Combustion Ion Chromatography-CIC)
D7360 Test Method for Analysis of Benzene by Gas Chromatography with External Calibration
1
This specification is under the jurisdiction of ASTM Committee D16 on Aromatic Hydrocarbons and Related Chemicals and is the direct responsibility of Subcommittee
D16.01 on Benzene, Toluene, Xylenes, Cyclohexane and Their Derivatives.
Current edition approved Aug. 1, 2010Nov. 1, 2012. Published September 2010December 2012. Originally approved in 1966. Last previous edition approved in 20092010
as D2359 – 09.D2359 – 10. DOI: 10.1520/D2359-10.10.1520/D2359-12.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D2359 − 12
D7375 Test Method for Trace Quantities of Water in Aromatic Hydrocarbons and Their Mixtures by Coulometric Karl Fischer
Titration
D7457 Test Method for Determining Chloride in Aromatic Hydrocarbons and Related Chemicals by Microcoulometry
D7504 Test Method for Trace Impurities in Monocyclic Aromatic Hydrocarbons by Gas Chromatography and Effective Carbon
Number
D7536 Test Method for Chlorine in Aromatics by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry
E29 Practice for Usin
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D4734-20(Specification)
Standard Specification for Refined Benzene-545

ABSTRACT
This specification covers benzene-545. Tests shall be performed to determine the property requirements of benzene-545 in accordance to the following test methods: benzene weight percentage; sulfur mass; thiophene mass; toluene mass; nonaromatic hydrocarbons weight percentage; nitrogen mass; acid wash color; bromine index, water, appearance, and solidification point.
SCOPE
1.1 This specification covers benzene-545.  
1.2 The following applies to all specified limits in this standard: for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit in accordance with the rounding-off method in Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 Consult current OSHA regulations, supplier’s Safety Data Sheets, and local regulations for all materials used in this specification.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D841-19(Specification)
Standard Specification for Nitration Grade Toluene

ABSTRACT
This specification covers the standard requirements for nitration grade toluene. The material shall be tested and sampled in accordance with standard test methods and practices and shall conform to the following requirements: volume of non-aromatic hydrocarbons; acid wash color; copper strip corrosion; appearance which shall be a clear liquid, free of sediment and haze; color in the platinum-cobalt scale; and distillation range.
SCOPE
1.1 This specification covers nitration grade toluene.  
1.2 The following applies to all specified limits in this specification: for purposes of determining conformance with this specification, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 Consult current OSHA regulations, supplier’s Safety Data Sheets, and local regulations for all materials used in this specification.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2359-19(Specification)
Standard Specification for Refined Benzene-535

ABSTRACT
This specification covers a grade of benzene known as refined benzene-535. Different tests shall be performed in order to determine the following properties of refined benzene-535: minimum purity, maximum toluene content, maximum sulfur content, maximum thiophene content, maximum nonaromatic hydrocarbon content, maximum nitrogen content, water content, maximum acid wash color, appearance, maximum color, 1,4 dioxane content, and minimum solidification point with anhydrous basis.
SCOPE
1.1 This specification covers a grade of benzene known as refined benzene-535.  
1.2 The following applies to all specified limits in this standard: for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 Consult current OSHA regulations, supplier’s Safety Data Sheets, and local regulations for all materials used in this specification.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D843-19(Specification)
Standard Specification for Nitration Grade Xylene

ABSTRACT
This specification covers nitration grade xylene. The nonaromatic hydrocarbons, acid wash color, copper corrosion, appearance, distillation range, initial distillation temperature, and dry point of nitration grade xylene shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers nitration grade xylene.  
1.2 The following applies to all specified limits in this standard: for purposes of determining conformance with this standard, an observed value or a calculated value shall be round off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the round-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.  
1.4 Consult OSHA regulations, supplier’s Safety Data Sheets, and local regulations for all materials used in this specification.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D6387-19(2023)(Test Method)
Standard Test Methods for Composition of Turpentine and Related Terpene Products by Capillary Gas Chromatography

SIGNIFICANCE AND USE
5.1 Earlier methods for characterizing turpentine and related terpene products were based on physical properties, such as those in Specification D13 and Test Methods D801 and D802, and packed column gas chromatography for the major constituents (for example, α-pinene, β-pinene) as in Test Method D3009. As terpene products became widely used as chemical raw material, the separation and quantitation of compounds present at lower concentrations in the product became more important. The capillary gas chromatographic technique described in these test methods is a rapid and convenient means to perform these analyses.
SCOPE
1.1 These test methods describe the determination of the amounts of α-pinene, β-pinene, dipentene, terpene alcohols, and other terpene compounds in turpentine and related terpene products using capillary gas chromatography. The two methods for determining the amount of the individual terpene compounds are the “internal standard” method, which yields absolute values, and the “area percent” method, which yields relative values.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of the standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: Overall this test method gives excellent repeatability but only moderate reproducibility. This greater than normal differential is a consequence of the variety of gas chromatography (GC) columns and other variables used by participants. These variables, coupled with the complex composition of the test products, enabled some workers to separate peaks that others reported as one peak; thus, this test method gives excellent precision within a given laboratory on a given GC. When laboratory to laboratory comparison have to be made, however, it is essential that the GC operating conditions be defined closely.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D2942-02(2023)(Test Method)
Standard Test Method for Total Acid Acceptance of Halogenated Organic Solvents (Nonreflux Methods)

SIGNIFICANCE AND USE
4.1 Solvents that have been depleted in stabilizer content can become acidic. Acids can cause corrosion to process and storage equipment used for halogenated solvents.  
4.2 Halogenated organic solvents may contain amine type (alkaline, aqueous extractable) acid accepting additives, neutral type (typically epoxide) acid accepting additives or both. This test method can determine the combined acid acceptance from both types of stabilizers. In addition, if the amine acid acceptance is determined by a separate procedure (see Test Methods D2106), the amount of neutral acid accepting stabilizers in a solvent can be calculated from the difference between combined and amine acid acceptance values.  
4.3 This test method may be used by producers and users to verify that a product is complying with acid acceptance product specifications or by users to monitor the acid accepting ability of a solvent in use.
SCOPE
1.1 This test method covers the determination of the total acid acceptance including amine and neutral type (alpha epoxide) stabilizers in halogenated organic solvents.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D1613-17(2023)(Test Method)
Standard Test Method for Acidity in Volatile Solvents and Chemical Intermediates Used in Paint, Varnish, Lacquer, and Related Products

SIGNIFICANCE AND USE
4.1 This test method is useful for determining low levels of acidity, below 0.05 %, in organic compounds and hydrocarbon mixtures. The total acidity is calculated as acetic acid or milligrams of sodium hydroxide per gram of sample.  
4.2 Acidity may be present as a result of contamination, decomposition during storage or distribution, or manufacture. This test method may be used in assessing compliance with a specification.
SCOPE
1.1 This test method covers the determination of total acidity as acetic acid, in concentrations below 0.05 %, in organic compounds and hydrocarbon mixtures used in paint, varnish, and lacquer solvents and diluents. It is known to be applicable to such mixtures as low molecular weight saturated and unsaturated alcohols, ketones, ethers, esters, hydrocarbon diluents, naphtha, and other light distillate petroleum fractions.  
1.2 For purposes of determining conformance of an observed value or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 For specific hazard information and guidance consult supplier’s Safety Data Sheet.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D365-23(Guide)
Standard Guide for Soluble Nitrocellulose Base Solutions

SIGNIFICANCE AND USE
3.1 Since the desired specifications and compositions of soluble nitrocellulose base solutions vary greatly, these methods are used to establish whether limits that shall be as agreed upon between the producer and the user have been met.
SCOPE
1.1 This guide covers the testing of soluble nitrocellulose base solutions that are made by dispersing various kinds and concentrations of soluble nitrocellulose (cellulose nitrate) in various solvent mixtures.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements see Section 11.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM D611-23(Test Method)
Standard Test Methods for Aniline Point and Mixed Aniline Point of Petroleum Products and Hydrocarbon Solvents

SIGNIFICANCE AND USE
5.1 The aniline point (or mixed aniline point) is useful as an aid in the characterization of pure hydrocarbons and in the analysis of hydrocarbon mixtures. Aromatic hydrocarbons exhibit the lowest, and paraffins the highest values. Cycloparaffins and olefins exhibit values that lie between those for paraffins and aromatics. In homologous series the aniline points increase with increasing molecular weight. Although it occasionally is used in combination with other physical properties in correlative methods for hydrocarbon analysis, the aniline point is most often used to provide an estimate of the aromatic hydrocarbon content of mixtures.
SCOPE
1.1 These test methods cover the determination of the aniline point of petroleum products and hydrocarbon solvents. Test Method A is suitable for transparent samples with an initial boiling point above room temperature and where the aniline point is below the bubble point and above the solidification point of the aniline-sample mixture. Test Method B, a thin-film method, is suitable for samples too dark for testing by Test Method A. Test Methods C and D are for samples that may vaporize appreciably at the aniline point. Test Method D is particularly suitable where only small quantities of sample are available. Test Method E describes a procedure using an automatic apparatus suitable for the range covered by Test Methods A and B.  
1.2 These test methods also cover the determination of the mixed aniline point of petroleum products and hydrocarbon solvents having aniline points below the temperature at which aniline will crystallize from the aniline-sample mixture.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 WARNING—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are given in Section 7.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM D1296-23(Test Method)
Standard Test Method for Odor of Volatile Solvents and Diluents

SIGNIFICANCE AND USE
3.1 The comparative odor characteristics can be used, combined with other tests, for product identification and assessing compliance with a specification.  
3.2 The residual odor characteristics can be used to judge the presence of relatively nonvolatile materials that may be associated with manufacture or contamination during distribution. Since volatile solvents and diluents are used in a wide variety of chemical processes and residual materials may affect the efficiency of such processes, this test method provides a comparative test for manufacturing control and assessing compliance with a specification.
SCOPE
1.1 This test method covers a comparative procedure for observing the characteristic and residual odors of volatile organic solvents and diluents to determine their odor acceptability in a solvent system.  
1.2 It is not intended that this test method be employed to determine subtle odor differences between materials or to determine odor intensity.  
1.3 It is recommended that this test method not be employed to determine the residual odor of a liquid if its time for evaporation to dryness at room temperature exceeds 30 min or as agreed upon.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 4.  
1.6 For specific hazard information, see the supplier's Material Safety Data Sheet (MSDS).  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off