ASTM D2464-23

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D2464 − 23 An American National Standard
Standard Specification for
Threaded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings,
1
Schedule 80
This standard is issued under the fixed designation D2464; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
1.1 This specification covers poly(vinyl chloride) (PVC)
Barriers to Trade (TBT) Committee.
threaded Schedule 80 pipe fittings. Included are requirements
for materials, workmanship, dimensions, and burst pressure.
2. Referenced Documents
NOTE 1—Threaded CPVC plastic pipe fittings, Schedule 80, which
2
were formerly included in this standard, are now covered by Specification
2.1 ASTM Standards:
F437.
D618 Practice for Conditioning Plastics for Testing
1.2 The products covered by this specification are intended
D1599 Test Method for Resistance to Short-Time Hydraulic
for use with the distribution of pressurized liquids only, which
Pressure of Plastic Pipe, Tubing, and Fittings
are chemically compatible with the piping materials. Due to
D1600 Terminology for Abbreviated Terms Relating to Plas-
inherent hazards associated with testing components and sys-
tics
tems with compressed air or other compressed gases some
D1784 Classification System and Basis for Specification for
manufacturers do not allow pneumatic testing of their products.
Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlo-
Consult with specific product/component manufacturers for
rinated Poly(Vinyl Chloride) (CPVC) Compounds
their specific testing procedures prior to pneumatic testing.
D2122 Test Method for Determining Dimensions of Ther-
NOTE 2—Pressurized (compressed) air or other compressed gases
moplastic Pipe and Fittings
contain large amounts of stored energy which present serious safety
hazards should a system fail for any reason. F412 Terminology Relating to Plastic Piping Systems
F437 Specification for Threaded Chlorinated Poly(Vinyl
1.3 The text of this specification references notes, footnotes,
Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80
and appendixes which provide explanatory material. These
F1498 Specification for Taper Pipe Threads 60° for Thermo-
notes and footnotes (excluding those in tables and figures) shall
plastic Pipe and Fittings
not be considered as requirements of the specification.
1.4 The values stated in inch-pound units are to be regarded 2.2 Federal Standard:
3
as the standard. The values given in parentheses are provided Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
for information only.
2.3 Military Standard:
3
1.5 The following safety hazards caveat pertains only to the
MIL-STD-129 Marking for Shipment and Storage
test method portion, Section 8, of this specification. This
2.4 NSF Standard:
standard does not purport to address all of the safety concerns,
Standard No. 14 for Plastic Piping Components and Related
if any, associated with its use. It is the responsibility of the user
4
Materials
of this standard to establish appropriate safety, health, and
Standard No. 61 for Drinking Water Systems Components—
environmental practices and determine the applicability of
4
Health Effects
regulatory limitations prior to use.
1.6 This international standard was developed in accor-
dance with internationally recognized principles on standard-
2
ization established in the Decision on Principles for the
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic the ASTM website.
3
Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings. DLA Document Services Building 4/D 700 Robbins Avenue Philadelphia, PA
Current edition approved Sept. 1, 2023. Published September 2023. Originally 19111-5094 http://quicksearch.dla.mil/
4
approved in 1965. Last previous edition approved in 2015 as D2464 – 15. DOI: Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., Ann
10.1520/D2464-23. Arbor, MI 48113-0140, http://www.nsf.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International,
...