ASTM F1836M-15

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F1836M −15 An American National Standard
Standard Specification for
1
Stuffing Tubes, Nylon, and Packing Assemblies (Metric)
This standard is issued under the fixed designation F1836M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope 2.3 ASME Standard:
ASME B1.1 Unified Inch Screw Threads (UN and UNR
1.1 This specification covers the general requirements for
4
Thread Form)
nylon stuffing tubes and packing assemblies. Nylon stuffing
2.4 IEC Standard
tubes are intended for making electric cable penetrations in
Standard 68-2-6 Environmental Testing–Part 2: Tests–Test
marine shipboard enclosures for electrical equipment. The
5
FC: Vibration (Sinusoidal) Sixth Edition
following types are suitable for both thin-wall enclosures up to
3
5mm( ⁄16 in.) thick and thick-wall enclosures, bulkheads, and
3. Terminology
3 3
decks of 5 to 19 mm ( ⁄16 to ⁄4 in.) thick.
3.1 Definitions of Terms Specific to This Standard:
1.2 This specification does not cover metal stuffing tubes.
3.1.1 nylon stuffıng tube, n—a marine electrical fitting used
for the sealing of cable penetration into shipboard enclosures
1.3 The values stated in SI units are to be regarded as
while maintaining or exceeding the degree of protection for
standard. No other units of measurement are included in this
which the enclosure is rated.
standard.
3.1.2 packing assembly, n—the compressible insert for the
1.4 This standard does not purport to address all of the
nylon stuffing tube. It consists of one neoprene bushing and
safety concerns, if any, associated with its use. It is the
three nylon washers.
responsibility of the user of this standard to establish appro-
3.1.3 enclosure, n—an electrical panel, cabinet, junction
priate safety and health practices and determine the applica-
box, light fixture, electrical equipment, control box, or panel.
bility of regulatory limitations prior to its use.
4. Classification
2. Referenced Documents
4.1 Nylon stuffing tubes shall be of the following types (see
2
Fig. 1):
2.1 ASTM Standards:
4.1.1 Type 1—straight—Unified Form Thread.
D2000 Classification System for Rubber Products in Auto-
4.1.2 Type 2—90°—Unified Form Thread.
motive Applications
4.1.3 Type 3—NPT—American Standard Pipe Thread.
D4066 Classification System for Nylon Injection and Extru-
4.1.4 Type 4—Y—Unified Form Thread.
sion Materials (PA)
2.2 NEMA Standards:
5. Ordering Information
Standard 250 Enclosures for Electrical Equipment (1000 V
3
5.1 Orders for stuffing tubes under this specification shall
Max)
include the following:
5.1.1 Type (see 4.1).
5.1.2 Part number (see Table 1).
1
This specification is under the jurisdiction of ASTM Committee F25 on Ships
5.1.3 Packing assembly size (see Fig. 2 and Table 2).
and Marine Technology and is the direct responsibility of Subcommittee F25.10 on
5.1.4 The O-ring included in the stuffing tube assembly has
Electrical.
a finite shelf life. If the stuffing tube assembly is used after the
Current edition approved Dec. 1, 2015. Published January 2016. Originally
approved in 1997. Last previous edition approved in 2013 as F1836M – 09 (2013).
DOI: 10.1520/F1836M-15.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
4
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Available from the International Electrotechnical Commission, 3 rue de
Standards volume information, refer to the standard’s Document Summary page on Varembe, Case postale 131, CH-1211, Geneva 20, Switzerland.
5
the ASTM website. Available from American Society of Mechanical Engineers (ASME), ASME
3
Available from National Electrical Manufacturers Association (NEMA), 1300 International Headquarters, Two Park Ave., New York, NY 10016-5990, http://
N. 17th St., Suite 1752, Rosslyn, VA 22209, http://www.nema.org. www.asme.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1836M−15
FIG. 1Stuffing Tube Types
FIG. 1Stuffing Tube Types (continued)
2

---------------------- Page: 2 ----------------------
F1836M−15
TABLE 1 Stuffing Tubes Part Numbers and Dimensional Data
Tube Part Cable Range Packing Clearance Hole Diameter O-Ring
A
Size No. in. mm Assembly for Tube Install Buna-N
min. max. min. max. in. mm Size
1 Type-1-001 0.077 0.300 1.96 7.62 -16 0.885 22.48 212
2 -002 0.275 0.472 6.99 11.99 -17 1.010 25.65 214
3 -003 0.410 0.472 10.41 11.99 -18 1.135 28.83 216
Straight 4 -004 0.450 0.7
...