ASTM D4434/D4434M-21
(Specification)Standard Specification for Poly(Vinyl Chloride) Sheet Roofing
Standard Specification for Poly(Vinyl Chloride) Sheet Roofing
ABSTRACT
This specification covers flexible fiber- or fabric-reinforced sheet made from poly(vinyl chloride) resin as the primary polymer intended for use in single-ply roofing membranes exposed to the weather. The sheet shall contain. In-place roof system design criteria such as fire resistance, material compatibility, wind uplift resistance, in-situ shrinkage, among others, are beyond the scope of this specification. The physical requirements for which the sheet materials shall be tested on and shall conform accordingly to are as follows: overall thickness and thickness over scrim; tensile strength at break; breaking strength; elongation at break; seam strength; retention of properties after heat aging; tear resistance and tearing strength; low temperature bend; cracking and crazing after accelerated weathering test; linear dimensional change; change in weight after immersion in water; and static and dynamic puncture resistance.
SCOPE
1.1 This specification covers flexible sheet made from poly(vinyl chloride) resin as the primary polymer intended for use in single-ply roofing membranes exposed to the weather. The sheet shall contain reinforcing fibers or reinforcing fabrics.
1.2 The tests and property limits used to characterize the sheet are values intended to ensure minimum quality for the intended purpose. In-place roof system design criteria, such as fire resistance, material compatibility, wind uplift resistance, in-situ shrinkage, among others, are factors that must be considered but are beyond the scope of this specification.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:D4434/D4434M −21
Standard Specification for
1
Poly(Vinyl Chloride) Sheet Roofing
This standard is issued under the fixed designation D4434/D4434M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope D638Test Method for Tensile Properties of Plastics
D751Test Methods for Coated Fabrics
1.1 This specification covers flexible sheet made from
D1004Test Method for Tear Resistance (Graves Tear) of
poly(vinyl chloride) resin as the primary polymer intended for
Plastic Film and Sheeting
use in single-ply roofing membranes exposed to the weather.
D1204Test Method for Linear Dimensional Changes of
Thesheetshallcontainreinforcingfibersorreinforcingfabrics.
Nonrigid Thermoplastic Sheeting or Film at Elevated
1.2 The tests and property limits used to characterize the
Temperature
sheet are values intended to ensure minimum quality for the
D2136Test Method for Coated Fabrics—Low-Temperature
intended purpose. In-place roof system design criteria, such as
Bend Test
fire resistance, material compatibility, wind uplift resistance,
D3045Practice for Heat Aging of Plastics Without Load
in-situ shrinkage, among others, are factors that must be
D5602/D5602MTest Method for Static Puncture Resistance
considered but are beyond the scope of this specification.
of Roofing Membrane Specimens
1.3 The values stated in either SI units or inch-pound units D5635/D5635MTest Method for Dynamic Puncture Resis-
tance of Roofing Membrane Specimens
are to be regarded separately as standard. The values stated in
each system may not be exact equivalents; therefore, each D7635/D7635MTestMethodforMeasurementofThickness
of Coatings Over Fabric Reinforcement
system shall be used independently of the other. Combining
values from the two systems may result in nonconformance G151PracticeforExposingNonmetallicMaterialsinAccel-
erated Test Devices that Use Laboratory Light Sources
with the standard.
G154Practice for Operating Fluorescent Ultraviolet (UV)
1.4 This standard does not purport to address all of the
Lamp Apparatus for Exposure of Nonmetallic Materials
safety concerns, if any, associated with its use. It is the
G155Practice for Operating XenonArc LightApparatus for
responsibility of the user of this standard to establish appro-
Exposure of Non-Metallic Materials
priate safety, health, and environmental practices and deter-
mine the applicability of regulatory limitations prior to use.
3. Classification
1.5 This international standard was developed in accor-
3.1 Type II—Reinforced sheet in which fibers are incorpo-
dance with internationally recognized principles on standard-
rated into a production process, for example as a carrier,
ization established in the Decision on Principles for the
without appreciably affecting such physical property charac-
Development of International Standards, Guides and Recom-
teristics of the finished product as tensile strength or ultimate
mendations issued by the World Trade Organization Technical
elongation, but may provide other desirable characteristics,
Barriers to Trade (TBT) Committee.
such as dimensional stability.
2. Referenced Documents
3.2 Type III—Sheet that is internally reinforced with fabric
2
2.1 ASTM Standards:
and which may also have a fabric backing.
D570Test Method for Water Absorption of Plastics
3.3 Type IV—Sheet that is internally reinforced with fabric
and which may also have a fabric backing with minimum
1
thickness of 0.91 mm [0.036 in.].
This specification is under the jurisdiction of ASTM Committee D08 on
RoofingandWaterproofingandisthedirectresponsibilityofSubcommitteeD08.18
on Nonbituminous Organic Roof Coverings.
4. Materials and Manufacture
Current edition approved Jan. 1, 2021. Published January 2021. Originally
4.1 The sheet shall consist of poly(vinyl chloride) resin in
approved in 1985. Last previous edition approved in 2015 as D4434/D4434M–15.
DOI: 10.1520/D4434_D4434M-21.
amounts greater than 50% of the total polymer content
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
suitably compounded with plasticizers, stabilizers, fillers,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
pigments,andotheringredientstosatisfythephysicalproperty
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. requirements and accelerated durability tests.
Co
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D4434/D4434M − 15 D4434/D4434M − 21
Standard Specification for
1
Poly(Vinyl Chloride) Sheet Roofing
This standard is issued under the fixed designation D4434/D4434M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope
1.1 This specification covers flexible sheet made from poly(vinyl chloride) resin as the primary polymer intended for use in
single-ply roofing membranes exposed to the weather. The sheet shall contain reinforcing fibers or reinforcing fabrics.
1.2 The tests and property limits used to characterize the sheet are values intended to ensure minimum quality for the intended
purpose. In-place roof system design criteria, such as fire resistance, material compatibility, wind uplift resistance, in-situ
shrinkage, among others, are factors that must be considered but are beyond the scope of this specification.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformancenonconformance with the standard.
1.4 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of
the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety
and health practices and determine the applicability of regulatory limitation prior to use.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D570 Test Method for Water Absorption of Plastics
D638 Test Method for Tensile Properties of Plastics
D751 Test Methods for Coated Fabrics
D1004 Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting
D1204 Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature
1
This specification is under the jurisdiction of ASTM Committee D08 on Roofing and Waterproofing and is the direct responsibility of Subcommittee D08.18 on
Nonbituminous Organic Roof Coverings.
Current edition approved Dec. 1, 2015Jan. 1, 2021. Published January 2016January 2021. Originally approved in 1985. Last previous edition approved in 20122015 as
D4434/D4434M – 12.D4434/D4434M – 15. DOI: 10.1520/D4434_D4434M-15.10.1520/D4434_D4434M-21.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D4434/D4434M − 21
D2136 Test Method for Coated Fabrics—Low-Temperature Bend Test
D3045 Practice for Heat Aging of Plastics Without Load
D5602D5602/D5602M Test Method for Static Puncture Resistance of Roofing Membrane Specimens
D5635D5635/D5635M Test Method for Dynamic Puncture Resistance of Roofing Membrane Specimens
D7635/D7635M Test Method for Measurement of Thickness of Coatings Over Fabric Reinforcement
G151 Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources
G154 Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Nonmetallic Materials
G155 Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials
3. Classification
3.1 Type II—Reinforced sheet in which fibers are incorporated into a produ
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.