ASTM B761-02
(Test Method)Standard Test Method for Particle Size Distribution of Metal Powders and Related Compounds by X-Ray Monitoring of Gravity Sedimentation
Standard Test Method for Particle Size Distribution of Metal Powders and Related Compounds by X-Ray Monitoring of Gravity Sedimentation
SCOPE
1.1 This test method covers the determination of particle size distributions of metal powders. Experience has shown that this test method is satisfactory for the analysis of elemental tungsten, tungsten carbide, molybdenum, and tantalum powders, all with an as-supplied Fisher number of 6 m or less, as determined by Test Method B 330. Other metal powders (for example, elemental metals, carbides, and nitrides) may be analyzed using this test method with caution as to significance until actual satisfactory experience is developed (see 7.2). The procedure covers the determination of particle size distribution of the powder in the following two conditions:
1.1.1 As the powder is supplied (as-supplied), and
1.1.2 After the powder has been deagglomerated by rod milling as described in Practice B 859.
1.2 This test method is applicable to particles of uniform density and composition having a particle size distribution range of 0.1 up to 100 μm.
1.2.1 However, the relationship between size and sedimentation velocity used in this test method assumes that particles sediment within the laminar flow regime. This requires that the particles sediment with a Reynolds number of 0.3 or less. Particle size distribution analysis for particles settling with a larger Reynolds number may be incorrect due to turbulent flow. Some materials covered by this test method may settle with Reynolds number greater than 0.3 if particles greater than 25 m are present. The user of this test method should calculate the Reynolds number of the largest particle expected to be present in order to judge the quality of obtained results. Reynolds number (Re) can be calculated using the flowing equation
Re = D3(ρ - ρ 0ρog
/18π2
where
D = the diameter of the largest particle expected to be present,
ρ = the particle density,
ρ0 = the suspending liquid density,
g = the acceleration due to gravity, and
π = is the suspending liquid viscosity.
A table of the largest particles that can be analyzed with Reynolds number of 0.3 or less in water at 35°C is given for a number of metals in Table 1. A column of the Reynolds number calculated for a 30-μm particle sedimenting in the same liquid system is given for each material also.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard information is given in Section 7.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B 761–02
Standard Test Method for
Particle Size Distribution of Metal Powders and Related
1
Compounds by X-Ray Monitoring of Gravity Sedimentation
This standard is issued under the fixed designation B 761; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope *
D = the diameter of the largest particle expected to be
1.1 This test method covers the determination of particle
present,
size distributions of metal powders. Experience has shown that
r = the particle density,
this test method is satisfactory for the analysis of elemental
r = the suspending liquid density,
0
tungsten, tungsten carbide, molybdenum, and tantalum pow-
g = the acceleration due to gravity, and
ders, all with an as-supplied Fisher number of 6 µm or less, as
h = is the suspending liquid viscosity.
determined by Test Method B 330. Other metal powders (for
example, elemental metals, carbides, and nitrides) may be
A table of the largest particles that can be analyzed with
analyzed using this test method with caution as to significance
Reynolds number of 0.3 or less in water at 35°C is given for a
until actual satisfactory experience is developed (see 7.2). The
numberofmetalsinTable1.AcolumnoftheReynoldsnumber
procedure covers the determination of particle size distribution
calculated for a 30–µm particle sedimenting in the same liquid
of the powder in the following two conditions:
system is given for each material also.
1.1.1 As the powder is supplied (as-supplied), and
1.3 This standard does not purport to address all of the
1.1.2 After the powder has been deagglomerated by rod
safety concerns, if any, associated with its use. It is the
milling as described in Practice B 859.
responsibility of the user of this standard to establish appro-
1.2 This test method is applicable to particles of uniform
priate safety and health practices and determine the applica-
density and composition having a particle size distribution
bility of regulatory limitations prior to use. Specific hazard
range of 0.1 up to 100 µm.
information is given in Section 7.
1.2.1 However, the relationship between size and sedimen-
tation velocity used in this test method assumes that particles
2. Referenced Documents
sediment within the laminar flow regime.This requires that the
2.1 ASTM Standards:
particles sediment with a Reynolds number of 0.3 or less.
B 330 Test Method forAverage Particle Size of Powders of
Particle size distribution analysis for particles settling with a
Refractory Metals and Their Compounds by the Fisher
largerReynoldsnumbermaybeincorrectduetoturbulentflow.
2
Sub-Sieve Sizer
Some materials covered by this test method may settle with
B 821 Guide for Liquid Dispersion of Metal Powders and
Reynolds number greater than 0.3 if particles greater than 25
2
Related Compounds for Particle Size Analysis
µm are present. The user of this test method should calculate
B 859 Practice for De-agglomeration of Refractory Metal
the Reynolds number of the largest particle expected to be
Powders and Their Compounds Prior to Particle Size
present in order to judge the quality of obtained results.
2
Analysis
Reynolds number (Re) can be calculated using the flowing
3
E 456 Terminology Related to Quality and Statistics
equation
E 691 Practice for Conducting an Interlaboratory Study to
3
3
D ~r – r !r g
Determine the Precision of a Test Method
0 0
Re 5 (1)
2
18h
3. Summary of Test Method
3.1 A carefully dispersed homogeneous suspension of the
where
powder is permitted to settle in a cell scanned by a collimated
X-ray beam of constant intensity. The net X-ray signal is
1 inversely proportional to the sample concentration in the
This test method is under the jurisdiction of ASTM Committee B09 on Metal
Powders and Metal Powder Products and is the direct responsibility of Subcom-
mittee B09.03 on Refractory Metal Powders.
2
Current edition approved Nov. 10, 2002. Published December 2002. Originally Annual Book of ASTM Standards, Vol 02.05.
3
approved in 1986. Last previous edition approved in 1998 as B 761 – 98. Annual Book of ASTM Standards, Vol 14.02.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B761–02
TABLE 1 Maximum Diameter of Metal Powders and Related Compounds That Can Be Analyzed with Reynolds Number of 0.3 or Less in
Waterat35°C
A
Particle Composition Particle Density Maximum Particle Diameter Reynolds Number for 30 µm
Cobalt 8.90 33.19 0.22
Copper 8.92 33.16
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.