ASTM F2643-20

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F2643 −20 An American National Standard
Standard Specification for
1
Powered Pot, Pan and Utensil Washing Sinks
This standard is issued under the fixed designation F2643; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope A436 Specification for Austenitic Gray Iron Castings
A554 Specification for Welded Stainless Steel Mechanical
1.1 This specification covers commercial powered pot, pan
Tubing
and utensil washing sinks.
A582/A582M Specification for Free-Machining Stainless
1.2 The values stated in inch-pound units are to be regarded
Steel Bars
as standard. The values given in parentheses are mathematical
B43 Specification for Seamless Red Brass Pipe, Standard
conversions to SI units that are provided for information only
Sizes
and are not considered standard.
B75 Specification for Seamless Copper Tube (Metric)
1.3 The following safety hazards caveat pertains only to the
B0075_B0075M
test methods portion, Section 12, of this specification: This B127 Specification for Nickel-Copper Alloy Plate, Sheet,
standard does not purport to address all of the safety concerns,
and Strip
if any, associated with its use. It is the responsibility of the user F760 Specification for Food Service Equipment Manuals
of this standard to establish appropriate safety, health, and
F2379 Test Method for Energy Performance of Powered
environmental practices and determine the applicability of Open Warewashing Sinks
4
regulatory limitations prior to use.
2.2 Federal Regulations:
1.4 This international standard was developed in accor- OSHA Title 29 Chapter XVII, Part 1910
5
dance with internationally recognized principles on standard-
2.3 American National Standards:
ization established in the Decision on Principles for the ANSI S1.4 Specification for Sound Level Meters
Development of International Standards, Guides and Recom-
ANSI S1.13 Methods for the Measurement of Sound Pres-
mendations issued by the World Trade Organization Technical sure Levels
Barriers to Trade (TBT) Committee.
2.4 National Electrical Manufacturers Association Stan-
6
dards:
2. Referenced Documents
NEMA ICS Industrial Controls and Systems
2
NEMA MG-1 Motors and Generators
2.1 ASTM Standards:
7
2.5 National Fire Protection Association Standards:
A29/A29M SpecificationforGeneralRequirementsforSteel
NFPA No. 70 National Electrical Code
Bars, Carbon and Alloy, Hot-Wrought
8
2.6 NSF International Standards:
A120 Specification for Pipe, Steel, Black and Hot-Dipped
NSF/ANSI 2 Food Equipment
Zinc-Coated (Galvanized) Welded and Seamless for Or-
3
NSF/ANSI 51 Plastic Materials and Components Used in
dinary Uses; Replaced by A 53 (Withdrawn 1987)
Food Equipment
A240/A240M Specification for Chromium and Chromium-
NSF Listings Food Equipment
Nickel Stainless Steel Plate, Sheet, and Strip for Pressure
9
2.7 Underwriters Laboratories Standards:
Vessels and for General Applications
UL 921 Commercial Electric Dishwashers
A276 Specification for Stainless Steel Bars and Shapes
4
AvailablefromU.S.GovernmentPrintingOfficeSuperintendentofDocuments,
1
This specification is under the jurisdiction of ASTM Committee F26 on Food 732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401, http://
Service Equipment and is the direct responsibility of Subcommittee F26.01 on www.access.gpo.gov.
5
Cleaning and Sanitation Equipment. Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
CurrenteditionapprovedJune1,2020.PublishedJuly2020.Originallyapproved 4th Floor, New York, NY 10036, http://www.ansi.org.
6
in 2007. Last previous edition approved in 2015 as F2643 – 15. DOI: 10.1520/ Available from National Electrical Manufacturers Association (NEMA), 1300
F2643-20. N. 17th St., Suite 1752, Rosslyn, VA 22209, http://www.nema.org.
2 7
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from National Fire Protection Association (NFPA), 1 Batterymarch
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Park, Quincy, MA 02169-7471, http://www.nfpa.org.
8
Standards volume information, refer to the standard’s Document Summary page on Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd.,Ann
the ASTM website. Arbor, MI 48113-0140, http://www.nsf.org.
3
9
The last approved version of this historical standard is referenced on Available from UL LLC, 333 Pfingsten Rd., Northbrook, IL 60062-2096,
www.astm.org. http://www.ul.com.
Copyright © ASTM Intern
...