ASTM D1188/D1188M-22
(Test Method)Standard Test Method for Bulk Specific Gravity and Density of Compacted Asphalt Mixtures Using Coated Samples
Standard Test Method for Bulk Specific Gravity and Density of Compacted Asphalt Mixtures Using Coated Samples
SIGNIFICANCE AND USE
3.1 This test method is useful in calculating percent air voids as given in Test Method D3203/D3203M. Since specific gravity has no units, it must be converted to density when this type of measurement is required. This conversion is made by multiplying the specific gravity at a given temperature by the density of water at the same temperature.
Note 2: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method covers the determination of bulk specific gravity of specimens of Parafilm-coated, compacted asphalt mixtures.
1.2 This method should be used with samples that contain open or interconnecting voids or absorb more than 2.0 % of water by volume, or both.
Note 1: A method for calculating the percent water absorbed by the specimen on a volume basis is described in Test Method D2726/D2726M.
1.3 The bulk specific gravity of the compacted asphalt mixtures may be used in calculating the unit weight of the mixture.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:D1188/D1188M −22
Standard Test Method for
Bulk Specific Gravity and Density of Compacted Asphalt
1
Mixtures Using Coated Samples
This standard is issued under the fixed designation D1188/D1188M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope 2. Referenced Documents
2
1.1 This test method covers the determination of bulk 2.1 ASTM Standards:
specific gravity of specimens of Parafilm-coated, compacted D979/D979MPractice for Sampling Bituminous Paving
asphalt mixtures. Mixtures
D1461Test Method for Moisture or Volatile Distillates in
1.2 This method should be used with samples that contain
Asphalt Mixtures
open or interconnecting voids or absorb more than 2.0% of
D2726/D2726MTest Method for Bulk Specific Gravity and
water by volume, or both.
Density of Non-Absorptive Compacted Asphalt Mixtures
NOTE 1—A method for calculating the percent water absorbed by the
D3203/D3203MTest Method for PercentAirVoids in Com-
specimenonavolumebasisisdescribedinTestMethodD2726/D2726M.
pacted Asphalt Mixtures
1.3 The bulk specific gravity of the compacted asphalt
D3666Specification for Minimum Requirements for Agen-
mixtures may be used in calculating the unit weight of the
cies Testing and Inspecting Road and Paving Materials
mixture.
D4753Guide for Evaluating, Selecting, and Specifying Bal-
ances and Standard Masses for Use in Soil, Rock, and
1.4 The values stated in either SI units or inch-pound units
Construction Materials Testing
are to be regarded separately as standard. The values stated in
D5361/D5361MPractice for Sampling Compacted Asphalt
each system may not be exact equivalents; therefore, each
Mixtures for Laboratory Testing
system shall be used independently of the other. Combining
D7227/D7227MPractice for Rapid Drying of Compacted
values from the two systems may result in nonconformance
Asphalt Mixture Specimens Using Vacuum DryingAppa-
with the standard.
ratus
1.5 The text of this standard references notes and footnotes
E1Specification for ASTM Liquid-in-Glass Thermometers
which provide explanatory material.These notes and footnotes
E1137/E1137MSpecification for Industrial Platinum Resis-
(excluding those in tables and figures) shall not be considered
tance Thermometers
as requirements of the standard.
1.6 This standard does not purport to address all of the
3. Significance and Use
safety concerns, if any, associated with its use. It is the
3.1 This test method is useful in calculating percent air
responsibility of the user of this standard to establish appro-
voids as given in Test Method D3203/D3203M. Since specific
priate safety, health, and environmental practices and deter-
gravity has no units, it must be converted to density when this
mine the applicability of regulatory limitations prior to use.
type of measurement is required. This conversion is made by
1.7 This international standard was developed in accor-
multiplying the specific gravity at a given temperature by the
dance with internationally recognized principles on standard-
density of water at the same temperature.
ization established in the Decision on Principles for the
NOTE 2—The quality of the results produced by this standard are
Development of International Standards, Guides and Recom-
dependent on the competence of the personnel performing the procedure
mendations issued by the World Trade Organization Technical
and the capability, calibration, and maintenance of the equipment used.
Barriers to Trade (TBT) Committee.
Agencies that meet the criteria of Specification D3666 are generally
considered capable of competent and objective testing, sampling,
1
This test method is under the jurisdiction of ASTM Committee D04 on Road
and Paving Materials and is the direct responsibility of Subcommittee D04.21 on
2
Specific Gravity and Density of Asphalt Mixtures. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved June 15, 2022. Published June 2022. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1951. Last previous edition approved in 2015 as D1188–07 (2015). Standards volume information, refer to the standard’s Document Summary page on
DOI: 10.1520/D1188_D1188M-22. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
-
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D1188 − 07 (Reapproved 2015) D1188/D1188M − 22
Standard Test Method for
Bulk Specific Gravity and Density of Compacted
1
BituminousAsphalt Mixtures Using Coated Samples
This standard is issued under the fixed designation D1188;D1188/D1188M; the number immediately following the designation indicates
the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope
1.1 This test method covers the determination of bulk specific gravity of specimens of Parafilm-coated, compacted bituminous
mixtures as defined in Terminology asphalt mixtures.E12.
1.2 This method should be used with samples that contain open or interconnecting voids or absorb more than 2 %2.0 % of water
by volume, or both, as determined by Section both.8.
NOTE 1—A method for calculating the percent water absorbed by the specimen on a volume basis is described in Test Method D2726/D2726M.
1.3 The bulk specific gravity of the compacted bituminousasphalt mixtures may be used in calculating the unit weight of the
mixture.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in nonconformance with the standard.
1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes
(excluding those in tables and figures) shall not be considered as requirements of the standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
1
This test method is under the jurisdiction of ASTM Committee D04 on Road and Paving Materials and is the direct responsibility of Subcommittee D04.21 on Specific
Gravity and Density of Asphalt Mixtures.
Current edition approved July 1, 2015June 15, 2022. Published October 2015June 2022. Originally approved in 1951. Last previous edition approved in 20072015 as
ε1
D1188 – 07 (2015). . DOI: 10.1520/D1188-07R15.10.1520/D1188_D1188M-22.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D1188/D1188M − 22
D979D979/D979M Practice for Sampling Bituminous Paving Mixtures
D1461 Test Method for Moisture or Volatile Distillates in Asphalt Mixtures
D2726D2726/D2726M Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Asphalt Mixtures
D3203D3203/D3203M Test Method for Percent Air Voids in Compacted Asphalt Mixtures
D3666 Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
D4753 Guide for Evaluating, Selecting, and Specifying Balances and Standard Masses for Use in Soil, Rock, and Construction
Materials Testing
D5361D5361/D5361M Practice for Sampling Compacted Asphalt Mixtures for Laboratory Testing
D6752D7227/D7227M Test Method for Bulk Specific Gravity and Density Practice for Rapid Drying of Compacted Asphalt
Mixtures Mixture Specimens Using Automatic Vacuum Sealing MethodDrying Apparatus
E12E1 Terminology Relating to Density and Specific Gravity of Solids, Liquids, and GasesSpecification for ASTM Liquid-
in-Glass Thermometers (Withdrawn 1996)
E1137/E1137M Specification for Industrial Platinum Resistance Thermometers
3. Significance and Use
3.1 This test method is useful in calculating percent air voids as
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.