iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D6451-99

(Guide)

Standard Guide for Application of Asphalt Based Protection Board

Standard Guide for Application of Asphalt Based Protection Board

SCOPE
1.1 This guide lists minimum application and installation requirements for semi-rigid protection board when used as protection for below grade or below wearing surface (like plaza decks) waterproofing.
1.2 The values stated in SI units are to be regarded as the standard. The values givein in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 8.

General Information

Status
Historical
Publication Date
09-Jul-1999
ICS
91.060.99 - Other elements of buildings
Technical Committee
D08 - Roofing and Waterproofing
Drafting Committee
D08.22 - Waterproofing and Dampproofing Systems
Current Stage
Ref Project

Relations

Replaced By
ASTM D6451-99(2006) - Standard Guide for Application of Asphalt Based Protection Board
Effective Date
01-May-2006
Referred By
ASTM D7693/D7693M-15 - Standard Guide for Application of Heat Weldable Modified Bituminous Waterproofing Membranes Systems for New Concrete Decks
Effective Date
10-Jul-1999

Buy Standard

ASTM D6451-99 - Standard Guide for Application of Asphalt Based Protection BoardASTM D6451-99 - Standard Guide for Application of Asphalt Based Protection Board
PreviousNext
Guide
ASTM D6451-99 - Standard Guide for Application of Asphalt Based Protection Board
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D6451–99
Standard Guide for
Application of Asphalt Based Protection Board
This standard is issued under the fixed designation D 6451; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope 6. Storage and Handling
1.1 This guide lists minimum application and installation 6.1 Store adhesive and mastic in tightly closed original
requirements for semi-rigid protection board when used as containers under conditions as recommended by the manufac-
protectionforbelowgradeorbelowwearingsurface(likeplaza turer.
decks) waterproofing. 6.2 Store the protection board in supplier’s original pack-
1.2 The values stated in SI units are to be regarded as the aging in a horizontal position to prevent deformation. Protect
standard. The values given in parentheses are for information against exposure to direct sunlight, precipitation, dust, and
only. other such contaminants.
1.3 This standard does not purport to address all of the
7. Materials
safety concerns, if any, associated with its use. It is the
responsibility of the user of this guide to establish appropriate 7.1 Adhesive, when used, must be acceptable to or have
safety and health practices and determine the applicability of been recommended by the waterproofing membrane manufac-
turer or supplier and further must be fully compatible with the
regulatory limitations prior to use. For specific precautionary
statement, see Section 8. membrane and the asphalt protection board.
7.2 Mastic and/or tape (if used on the joints) must be
2. Referenced Documents
acceptable to or have been recommended by the waterproofing
2.1 ASTM Standards: membrane manufacturer or supplier and further be fully
D 1079 Terminology Relating to Roofing, Waterproofing compatible with the membrane and the asphalt protection
and Bituminous Materials board.
D 5957 Guide for Flood Testing Horizontal Waterproofing
2 8. Safety Precautions
Installations
8.1 Store flammable materials in a manner that will not pose
3. Terminology
a fire hazard. Solvent bearing adhesives may be flammable. Do
3.1 Definitions—For definitions of terms relating to water- not use flammable materials near an open flame or equipment
proofing, see Terminology D 1079. that may produce sparks.
4. Significance and Use 9. Environmental Conditions at Time of Application
4.1 This guide outlines general procedures for the storage 9.1 Environmental conditions under which installation may
and application of semi-rigid protection board to below grade proceed shall be as recommended by the suppliers of the
and below wearing surface waterproofing. The proper applica- adhesive and the protection board.
tion is necessary to prevent damage to the waterproofing
10. Substrate Preparation
membrane during backfilling, paving, or other construction
10.1 The waterproofing membrane must be clean and suf-
operations, as well as to minimize the effects of soil stresses.
4.2 This guide is intended to supplement instructions from ficiently dry so as not to interfere with adhesion of the
protection board.
designers and manufacturers.
10.2 If a flood test of the membrane is desired, this test
5. Delivery of Materials
should be made before placing the protection course, in
5.1 Deliver materials in supplier’s original containers and accordance with Guide D 5957.
packaging.
11. Installation
11.1 Install protection board within 24 h of completing the
This guide is under the jurisdiction of ASTM Committee D-8 on Roofing,
waterproofing membrane installation. Delay installation of the
Waterproofing and Bituminous Materials and is the direct responsibility of Sub-
protection board until the waterproofing film cures. If flood
committee D08.22 on Waterproofing and Damproofing Systems.
Current edition approved July 10, 1999. Published September 1999.
Annual Book of ASTM Standards, Vol 04.04.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
D6451
testing is conducted the application should be as soon as corner to make an “X” across the center of the surface of each
possible after the surface is dry and clean. protection board to be installed against the waterproofing
11.2 On Low Slope Surfaces: membrane. Full adhesive coating of the board is also accept-
11.2.1 Lay protection board on
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D6451/D6451M-99(2021)(Guide)
Standard Guide for Application of Asphalt-Based Protection Board

SIGNIFICANCE AND USE
4.1 This guide outlines general procedures for the storage and application of semi-rigid protection board to below-grade and below wearing surface waterproofing. The proper application is necessary to prevent damage to the waterproofing membrane during backfilling, paving, or other construction operations, as well as to minimize the effects of soil stresses.  
4.2 This guide is intended to supplement instructions from designers and manufacturers.
SCOPE
1.1 This guide lists minimum application and installation requirements for semi-rigid protection board when used as protection for below-grade or below wearing surface (like plaza decks) waterproofing.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 8.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    2 pages
    English language
    sale 15% off
ASTM
ASTM D6506/D6506M-01(2018)e1(Specification)
Standard Specification for Asphalt Based Protection Board for Below-Grade Waterproofing

ABSTRACT
This specification covers the manufacture, testing, and physical requirements of two classes of asphalt based protection board used for protecting the integrity of below grade or below wearing surface waterproofing. Class A is made with asphalt saturated organic felt on the bottom and a coated or saturated non-woven glass felt on top, while Class B is made with glass fabrics both top and bottom. The boards shall be sampled for testing, and each class shall conform accordingly to specified individual values of the following physical properties: nominal thickness; puncture strength; water absorption; asphalt content; and resistance to decay.
SCOPE
1.1 This specification covers an asphalt based protection board used for protecting the integrity of below grade or below wearing surface waterproofing. The protection board protects the waterproofing system from backfill, surfacing, construction activities, and weathering conditions prior to backfilling or applying surfacing.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D6451/D6451M-99(2021)(Guide)
Standard Guide for Application of Asphalt-Based Protection Board

SIGNIFICANCE AND USE
4.1 This guide outlines general procedures for the storage and application of semi-rigid protection board to below-grade and below wearing surface waterproofing. The proper application is necessary to prevent damage to the waterproofing membrane during backfilling, paving, or other construction operations, as well as to minimize the effects of soil stresses.  
4.2 This guide is intended to supplement instructions from designers and manufacturers.
SCOPE
1.1 This guide lists minimum application and installation requirements for semi-rigid protection board when used as protection for below-grade or below wearing surface (like plaza decks) waterproofing.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 8.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    2 pages
    English language
    sale 15% off
ASTM
ASTM E1190-21(Test Method)
Standard Test Methods for Strength of Power-Actuated Fasteners Installed in Structural Members

SIGNIFICANCE AND USE
4.1 These test methods are intended to measure the anchoring capability and shear resistance of power-actuated fasteners to provide information from which applicable design values are to be derived for use in structural applications, such as in members of concrete, concrete masonry, and steel.
SCOPE
1.1 These test methods describe procedures for determining the static axial tensile and shear strengths of power-actuated fasteners installed in structural members made of concrete, concrete masonry, and steel.  
1.2 These test methods are intended for use with fasteners that are installed perpendicular to a plane surface of the structural member.  
1.3 Tests for combined tension and shear, fatigue, dynamic, and torsional load resistance are not covered.  
1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 6.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D6506/D6506M-01(2018)e1(Specification)
Standard Specification for Asphalt Based Protection Board for Below-Grade Waterproofing

ABSTRACT
This specification covers the manufacture, testing, and physical requirements of two classes of asphalt based protection board used for protecting the integrity of below grade or below wearing surface waterproofing. Class A is made with asphalt saturated organic felt on the bottom and a coated or saturated non-woven glass felt on top, while Class B is made with glass fabrics both top and bottom. The boards shall be sampled for testing, and each class shall conform accordingly to specified individual values of the following physical properties: nominal thickness; puncture strength; water absorption; asphalt content; and resistance to decay.
SCOPE
1.1 This specification covers an asphalt based protection board used for protecting the integrity of below grade or below wearing surface waterproofing. The protection board protects the waterproofing system from backfill, surfacing, construction activities, and weathering conditions prior to backfilling or applying surfacing.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM F2697-15(Test Method)
Standard Test Methods for Physical Assault on Overhead Horizontal Fixed Barriers for Detention and Correctional Facilities

SIGNIFICANCE AND USE
4.1 A major concern for administrative officials is the security of barriers used in detention/correctional facilities. These test methods are designed to aid in identifying levels of physical security for horizontal fixed barriers, which serve to enclose or separate secure areas. This does not apply to the passage of contraband or vandalism.  
4.2 These test methods are not intended to provide a measure of resistance for a ceiling subjected to attack by corrosive agents, by high-powered rifles, explosives, sawing, or other such methods not typically available to inmates. These test methods are intended to evaluate the resistance of a ceiling to violent attacks by sustained manpower using battering devices, such as benches, barbells, bunks, or tables; and by an upward static force such that could be applied by an inmate pushing against the ceiling with his hands, feet, or back (that is, squat position on a top bunk in a cell). Attacks from outside the facility and fire resistance ratings are not addressed in this standard.  
4.3 The primary purpose or result of these test methods is to approximate the levels of abuse to which horizontal fixed barriers could possibly be subjected in the field. The desired result of its use is to help provide assurance of protection to the public, to facility personnel, and to the inmates themselves.  
4.4 It is recommended that detention/correctional facility administration provide adequate training, supervision, and preventive maintenance programs to enable horizontal fixed barriers to function as intended throughout the expected service life.
SCOPE
1.1 These test methods cover requirements for simulated service tests and testing equipment for determining the performance characteristics of horizontal fixed barriers designed to incarcerate inmates in detention and correctional institutions. The testing equipment provides for the setup and testing of sample barriers and installation systems.  
1.2 It is the intent of these test methods to help ensure that detention security horizontal fixed barriers perform at or above minimum acceptable levels for control of passage to unauthorized or secure areas, to confine inmates, and to delay and frustrate escape attempts. Provide security grilles, access doors, light fixtures, and similar assemblies compatible with these levels of performance, with test apparatus adjustments as required to suit the particular product.  
1.3 These test methods apply to horizontal fixed barriers enclosing or separating secure areas of detention/correctional facilities.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversion to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    11 pages
    English language
    sale 15% off
ASTM
ASTM F319-19(2024)(Practice)
Standard Practice for Polarized Light Detection of Flaws in Aerospace Transparency Heating Elements

SIGNIFICANCE AND USE
4.1 This practice is useful as a screening basis for acceptance or rejection of transparencies during manufacturing so that units with identifiable flaws will not be carried to final inspection for rejection at that time.  
4.2 This practice may also be employed as a go-no go technique for acceptance or rejection of the finished product.  
4.3 This practice is simple, inexpensive, and effective. Flaws identified by this practice, as with other optical methods, are limited to those that produce temperature gradients when electrically powered. Any other type of flaw, such as minor scratches parallel to the direction of electrical flow, are not detectable.
SCOPE
1.1 This practice covers a standard procedure for detecting flaws in the conductive coating (heater element) by the observation of polarized light patterns.  
1.2 This practice applies to coatings on surfaces of monolithic transparencies as well as to coatings imbedded in laminated structures.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 6.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D396-24(Specification)
Standard Specification for Fuel Oils

ABSTRACT
This specification covers grades of fuel oil intended for use in various types of fuel-oil-burning equipment under various climatic and operating conditions. These grades include the following: Grades No. 1 S5000, No. 1 S500, No. 2 S5000, and No. 2 S500 for use in domestic and small industrial burners; Grades No. 1 S5000 and No. 1 S500 adapted to vaporizing type burners or where storage conditions require low pour point fuel; Grades No. 4 (Light) and No. 4 (Heavy) for use in commercial/industrial burners; and Grades No. 5 (Light), No. 5 (Heavy), and No. 6 for use in industrial burners. Preheating is usually required for handling and proper atomization. The grades of fuel oil shall be homogeneous hydrocarbon oils, free from inorganic acid, and free from excessive amounts of solid or fibrous foreign matter. Grades containing residual components shall remain uniform in normal storage and not separate by gravity into light and heavy oil components outside the viscosity limits for the grade. The grades of fuel oil shall conform to the limiting requirements prescribed for: (1) flash point, (2) water and sediment, (3) physical distillation or simulated distillation, (4) kinematic viscosity, (5) Ramsbottom carbon residue, (6) ash, (7) sulfur, (8) copper strip corrosion, (9) density, and (10) pour point. The test methods for determining conformance to the specified properties are given.
SCOPE
1.1 This specification (see Note 1) covers grades of fuel oil intended for use in various types of fuel-oil-burning equipment under various climatic and operating conditions. These grades are described as follows:  
1.1.1 Grades No. 1 S5000, No. 1 S500, No. 1 S15, No. 2 S5000, No. 2 S500, and No. 2 S15 are middle distillate fuels for use in domestic and small industrial burners. Grades No. 1 S5000, No. 1 S500, and No. 1 S15 are particularly adapted to vaporizing type burners or where storage conditions require low pour point fuel.  
1.1.2 Grades B6–B20 S5000, B6–B20 S500, and B6–B20 S15 are middle distillate fuel/biodiesel blends for use in domestic and small industrial burners.  
1.1.3 Grades No. 4 (Light) and No. 4 are heavy distillate fuels or middle distillate/residual fuel blends used in commercial/industrial burners equipped for this viscosity range.  
1.1.4 Grades No. 5 (Light), No. 5 (Heavy), and No. 6 are residual fuels of increasing viscosity and boiling range, used in industrial burners. Preheating is usually required for handling and proper atomization.  
Note 1: For information on the significance of the terminology and test methods used in this specification, see Appendix X1.
Note 2: A more detailed description of the grades of fuel oils is given in X1.3.  
1.2 This specification is for the use of purchasing agencies in formulating specifications to be included in contracts for purchases of fuel oils and for the guidance of consumers of fuel oils in the selection of the grades most suitable for their needs.  
1.3 Nothing in this specification shall preclude observance of federal, state, or local regulations which can be more restrictive.  
1.4 The values stated in SI units are to be regarded as standard.  
1.4.1 Non-SI units are provided in Table 1 and Table 2 and in 7.1.2.1/7.1.2.2 because these are common units used in the industry.
Note 3: The generation and dissipation of static electricity can create problems in the handling of distillate burner fuel oils. For more information on the subject, see Guide D4865.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    13 pages
    English language
    sale 15% off
  • Technical specification
    13 pages
    English language
    sale 15% off
ASTM
ASTM D4479/D4479M-07(2024)(Specification)
Standard Specification for Asphalt Roof Coatings—Asbestos-Free

ABSTRACT
This specification covers the properties and requirements for two types of asbestos-free asphalt roof coatings consisting of an asphalt base, volatile petroleum solvents, and mineral or other stabilizers, or both, mixed to a smooth, uniform consistency suitable for application by squeegee, three-knot brush, paint brush, roller, or by spraying. Type I is made from asphalts characterized as self-healing, adhesive, and ductile, while Type II is made from asphalts characterized by high softening point and relatively low ductility. The coatings shall conform to specified composition limits for water, nonvolatile matter, minerals and/or other stabilizers, and bitumen (asphalt). They shall also meet physical requirements as to uniformity, consistency, and pliability and behavior at given temperatures.
SCOPE
1.1 This specification covers asbestos-free asphalt roof coatings of brushing or spraying consistency.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 The following precautionary caveat pertains only to the test method portion, Section 8, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D1187/D1187M-97(2024)(Specification)
Standard Specification for Asphalt-Base Emulsions for Use as Protective Coatings for Metal

ABSTRACT
This specification establishes the manufacture, testing, and performance requirements of two types of asphalt-based emulsions for use in a relatively thick film as a protective coating for metal surfaces. Type I are quick-setting emulsified asphalt suitable for continuous exposure to water within a few days after application and drying. Type II, on the other hand, are emulsified asphalt suitable for continuous exposure to the weather, only after application and drying. Upon being sampled appropriately, the materials shall conform to composition requirements as to density, residue by evaporation, nonvolatile matter soluble in trichloroethylene, and ash and water content. They shall also adhere to performance requirements as to uniformity, consistency, stability, wet flow, firm set, heat test, flexibility, resistance to water, and loss of adhesion.
SCOPE
1.1 This specification covers emulsified asphalt suitable for application in a relatively thick film as a protective coating for metal surfaces.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off