iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D6072-08

(Guide)

Standard Practice for Obtaining Samples of Geosynthetic Clay Liners

Standard Practice for Obtaining Samples of Geosynthetic Clay Liners

SIGNIFICANCE AND USE
This practice provides a procedure by which samples of GCL should be obtained for laboratory testing. The practice applies to materials obtained prior to installation (either at a job site or at a production facility) or exhumed material after installation.
Only GCL samples obtained in accordance with 5.1 of this practice will be considered representative of the actual manufactured GCL for quality assurance/quality control (QA/QC) purposes..
The quantity of GCL received by the laboratory should be sufficient for the preparation of several representative test specimens for the standardized physical, hydraulic, and mechanical tests to be performed on the GCLs.
The procedures in this practice should be used by plant and field personnel for obtaining GCL samples for laboratory testing.
SCOPE
1.1 This practice covers procedures for sampling geosynthetic clay liners (GCLs) for the purpose of laboratory testing. These procedures are designed to ensure that representative samples are obtained and properly packaged for submittal to a testing laboratory.
1.2 The procedures in this practice may be applied to either samples of unhydrated GCLs obtained at the project site prior to installation (or at the production facility, prior to shipment to the project site) or samples exhumed from a project site after installation.
1.3 It is assumed that the number  of samples to be obtained has already been determined in the project specification, standard test method, or by prior agreement between the purchaser and seller. This practice covers only the methods for obtaining a pre-arranged number of samples and does not describe methods for obtaining individual specimens from the sample.
1.4 The values stated in SI units are to be regarded as the standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
30-Jun-2008
ICS
13.080.99 - Other standards related to soil quality
Technical Committee
D35 - Geosynthetics
Drafting Committee
D35.04 - Geosynthetic Clay Liners
Current Stage
Ref Project

Relations

Replaces
ASTM D6072-96(2002) - Standard Guide for Obtaining Samples of Geosynthetic Clay Liners
Effective Date
01-Jul-2008
Replaced By
ASTM D6072/D6072M-09 - Standard Practice for Obtaining Samples of Geosynthetic Clay Liners
Effective Date
01-Nov-2009

Buy Standard

ASTM D6072-08 - Standard Practice for Obtaining Samples of Geosynthetic Clay LinersASTM D6072-08 - Standard Practice for Obtaining Samples of Geosynthetic Clay Liners
PreviousNext
Guide
ASTM D6072-08 - Standard Practice for Obtaining Samples of Geosynthetic Clay Liners
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM D6072-08 - Standard Practice for Obtaining Samples of Geosynthetic Clay LinersREDLINE ASTM D6072-08 - Standard Practice for Obtaining Samples of Geosynthetic Clay Liners
PreviousNext
Guide
REDLINE ASTM D6072-08 - Standard Practice for Obtaining Samples of Geosynthetic Clay Liners
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information.
Designation:D6072–08
Standard Practice for
1
Obtaining Samples of Geosynthetic Clay Liners
This standard is issued under the fixed designation D6072; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D5888 Guide for Storage and Handling of Geosynthetic
Clay Liners
1.1 This practice covers procedures for sampling geosyn-
thetic clay liners (GCLs) for the purpose of laboratory testing.
3. Terminology
These procedures are designed to ensure that representative
3.1 Definitions:
samples are obtained and properly packaged for submittal to a
3.1.1 geosynthetic clay liner (GCL), n—a manufactured
testing laboratory.
hydraulic barrier consisting of clay bonded to a layer or layers
1.2 The procedures in this practice may be applied to either
of geosynthetics.
samples of unhydrated GCLs obtained at the project site prior
3.1.2 sample, n—a portion of a material which is taken for
toinstallation(orattheproductionfacility,priortoshipmentto
testing or for record purposes (See Practice D4354).
the project site) or samples exhumed from a project site after
3.1.3 specimen, n—a specific portion of a material or
installation.
laboratory sample upon which a test is performed or which is
1.3 It is assumed that the number of samples to be obtained
taken for that purpose (See Practice D4354).
has already been determined in the project specification,
3.1.4 For definitions of other geosynthetic terms used in this
standard test method, or by prior agreement between the
practice, refer to Terminology D4439.
purchaser and seller. This practice covers only the methods for
obtaining a pre-arranged number of samples and does not
4. Significance and Use
describe methods for obtaining individual specimens from the
4.1 This practice provides a procedure by which samples of
sample.
GCL should be obtained for laboratory testing. The practice
1.4 The values stated in SI units are to be regarded as the
appliestomaterialsobtainedpriortoinstallation(eitheratajob
standard.
site or at a production facility) or exhumed material after
1.5 This standard does not purport to address all of the
installation.
safety concerns, if any, associated with its use. It is the
4.2 Only GCL samples obtained in accordance with 5.1 of
responsibility of the user of this standard to establish appro-
this practice will be considered representative of the actual
priate safety and health practices and determine the applica-
manufactured GCL for quality assurance/quality control (QA/
bility of regulatory limitations prior to use.
QC) purposes.
4.3 The quantity of GCL received by the laboratory should
2. Referenced Documents
2 be sufficient for the preparation of several representative test
2.1 ASTM Standards:
specimens for the standardized physical, hydraulic, and me-
D4220 Practices for Preserving and Transporting Soil
chanical tests to be performed on the GCLs.
Samples
4.4 The procedures in this practice should be used by plant
D4354 Practice for Sampling of Geosynthetics for Testing
and field personnel for obtaining GCL samples for laboratory
D4439 Terminology for Geosynthetics
testing.
1
5. Procedure
This practice is under the jurisdiction of ASTM CommitteeD35 on Geosyn-
thetics and is the direct responsibility of Subcommittee D35.04 on Geosynthetic
5.1 Obtaining Samples prior to Installation:
Clay Liners.
5.1.1 In accordance with the project specifications or with
Current edition approved July 1, 2008. Published September 2008. Originally
approved in 1996. Last previous edition approved in 2002 as D6072–96(2002). Practice D4354, divide the shipment or other given quantity of
DOI: 10.1520/D6072-08.
GCL into lots, and select lot and laboratory samples. This will
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
usually involve the selection of a certain number of finished
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
GCL rolls from which samples will be cut.
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D6072–08
5.1.2 Affix on the packaging of the GCLrolls to be sampled 5.1.13 Samples should be transmitted to the laboratory in a
adhesive labels or other markings which clearly identify that manner that minimizes the amount elapsed time, sample
the roll is to be sampled. handling, disturbances (such as moisture, vibration, impact,
etc.) that could occur in transit. Expedited delivery will
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D6072–96 (Reapproved 2002)
Standard Guide for Designation: D 6072 – 08
Standard Practice for
1
Obtaining Samples of Geosynthetic Clay Liners
This standard is issued under the fixed designation D 6072; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This practice covers procedures for sampling geosynthetic clay liners (GCLs) for the purpose of laboratory testing. These
procedures are designed to ensure that representative samples are obtained and properly packaged for submittal to a testing
laboratory.
1.2TheproceduresinthispracticemaybeappliedtosamplesofunhydratedGCLsobtainedattheprojectsiteorattheproduction
facility, prior to shipment to the project site.
1.2 The procedures in this practice may be applied to either samples of unhydrated GCLs obtained at the project site prior to
installation (or at the production facility, prior to shipment to the project site) or samples exhumed from a project site after
installation.
1.3 It is assumed that the number of samples to be obtained has already been determined in the project specification, standard
test method, or by prior agreement between the purchaser and seller. This practice covers only the methods for obtaining a
pre-arranged number of samples and does not describe methods for obtaining individual specimens from the sample.
1.4 The values stated in SI units are to be regarded as the standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards: ASTM Standards:
D 4220 Practices for Preserving and Transporting Soil Samples
D 4354 Practice for Sampling of Geosynthetics for Testing
2
D 4439Terminology for Geosynthetics
2
D4873Guide forIdentification, Storage, and Handling of Geosynthetic Rolls and Samples Terminology for Geosynthetics
D 5888 Guide for Storage and Handling of Geosynthetic Clay Liners
3. Terminology
3.1 Definitions:
3.1.1 geosynthetic clay liner (GCL), n— a manufactured hydraulic barrier consisting of clay bonded to a layer or layers of
geosynthetics.
3.1.2 sample, n—a portion of a material which is taken for testing or for record purposes (See Practice D 4354).
3.1.3 specimen, n—a specific portion of a material or laboratory sample upon which a test is performed or which is taken for
that purpose (See Practice D 4354).
3.1.4 For definitions of other geosynthetic terms used in this practice, refer to Terminology D 4439.
4. Significance and Use
4.1 This practice provides a methodprocedure by which samples of GCL mayshould be obtained for laboratory testing. The
1
This practice is under the jurisdiction ofASTM Committee D35 on Geosynthetics and is the direct responsibility of Subcommittee D35.04 on Geosynthetic Clay Liners.
Current edition approved December 10, 1996. Published December 1997.
Current edition approved July 1, 2008. Published September 2008. Originally approved in 1996. Last previous edition approved in 2002 as D 6072–96(2002).
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
, Vol 04.13.volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D6072–08
practice applies to materials obtained prior to installation (either at a job site or at a production facility) or exhumed material after
installation.
4.2 Only GCL samples obtained in accordance with 5.1 of this practice will be considered representative of the actual
manufactured GCL for quality assurance/quality control (QA/QC) purposes.
4.3 The quantity of GCL received by the laboratory should be sufficient for the preparation of several representative test
specimens for a variety of the standardized physical, hydraulic, and mechanical tests commonly to be performed on the GCLs.
4.4 TheproceduresinthispracticeshouldbeusedbyplantandfieldpersonnelforobtainingGCLsamplesforlaboratorytesting.
5. Procedu
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D6072/D6072M-19e1(Practice)
Standard Practice for Obtaining Samples of Geosynthetic Clay Liners

SIGNIFICANCE AND USE
4.1 This practice provides a procedure by which samples of GCL should be obtained for laboratory testing. The practice applies to materials obtained prior to installation (either at a job site or at a production facility) or exhumed material after installation.  
4.2 Only GCL samples obtained in accordance with 5.1 of this practice will be considered representative of the actual manufactured GCL for quality assurance/quality control (QA/QC) purposes.  
4.3 The quantity of GCL received by the laboratory should be sufficient for the preparation of several representative test specimens for the standardized physical, hydraulic, and mechanical tests to be performed on the GCLs.  
4.4 The procedures in this practice should be used by plant and field personnel for obtaining GCL samples for laboratory testing.
SCOPE
1.1 This practice covers procedures for sampling geosynthetic clay liners (GCLs) for the purpose of laboratory testing. These procedures are designed to ensure that representative samples are obtained and properly packaged for submittal to a testing laboratory.  
1.2 The procedures in this practice may be applied to either samples of unhydrated GCLs obtained at the project site prior to installation (or at the production facility, prior to shipment to the project site) or samples exhumed from a project site after installation.  
1.3 It is assumed that the number of samples to be obtained has already been determined in the project specification, standard test method, or by prior agreement between the purchaser and seller. This practice covers only the methods for obtaining a pre-arranged number of samples and does not describe methods for obtaining individual specimens from the sample.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM E3382-23(Guide)
Standard Guide for Developing Representative Background Concentrations at Sediment Sites — Framework Overview, Including Conceptual Site Model Considerations

SIGNIFICANCE AND USE
4.1 Intended Use:  
4.1.1 This guide may be used by various parties involved in sediment corrective action programs, including regulatory agencies, project sponsors, environmental consultants, toxicologists, risk assessors, site remediation professionals, environmental contractors, and other stakeholders.  
4.2 Updates to CSM:  
4.2.1 The CSM should be updated as needed and refined to describe the physical properties, chemical composition and occurrence, biological features, and environmental conditions of the sediment corrective action project (Guide E1689).  
4.3 Reference Material:  
4.3.1 This guide should be used in conjunction with other ASTM guides listed in 2.1 (especially Guides E3163, E3164, E3240, E3242, and E3344), as well as the material in the References section (including (1)).  
4.4 Flexible Site-Specific Implementation:  
4.4.1 This guide provides a systematic but flexible framework to accommodate variations in approaches by regulatory agencies and by the user based on project objectives, site complexity, unique site features, regulatory requirements, newly developed guidance, newly published scientific research, changes in regulatory criteria, advances in scientific knowledge and technical capability, and unforeseen circumstances.  
4.5 Regulatory Frameworks:  
4.5.1 This guide is intended to be applicable to a broad range of local, state, tribal, federal, or international jurisdictions, each with its own unique regulatory framework. As such, this guide does not provide a detailed discussion of the requirements or guidance associated with any of these regulatory frameworks, nor is it intended to supplant applicable regulations and guidance. The user of this guide will need to be aware of the regulatory requirements and guidance in the jurisdiction where the work is being performed.  
4.6 Systematic Project Planning and Scoping Process:  
4.6.1 When applying this guide, the user should undertake a systematic project planning and sco...
SCOPE
1.1 This guide provides an overarching framework for the development of representative sediment background concentrations at contaminated sediment sites. It is intended to inform, complement, and support but not supersede the guidelines established by local, state, tribal, federal, or international agencies.  
1.2 Technically defensible representative sediment background concentrations are critical for several purposes (Guide E3242) (1)2. These include sediment site delineation, establishing remedial goals, remedy selection, assessment of risks posed by representative background concentrations, and establishing appropriate post-remedial monitoring plans.  
1.3 As part of the overall framework presented in this guide, Guide E3240 provides a general discussion of how Conceptual Site Model (CSM) development fits into the risk-based corrective action framework for contaminated sediment sites. However, not all elements of a sediment CSM need to be considered when developing representative sediment background concentrations; those that do are discussed in detail in Section 7 of this guide.  
1.3.1 As additional data are collected and analyzed, the CSM should be updated as needed.  
1.3.2 This guide is related to several other guides. Guide E3344 describes how to select an appropriate background reference area(s). Guide E3164 covers the sampling methodologies used in the field to obtain sediment samples (whether from the sediment site or background reference area[s]), and Guide E3163 discusses appropriate laboratory methodologies to use for the chemical analysis of potential contaminants of concern (PCOCs) in sediment samples. Guide E3242 describes how to evaluate candidate background data to obtain representative background data sets (including statistical, geochemical, and forensic considerations) and then how to use them to calculate representative sediment background concentrations. Relevant content contained in Guides ...

  • Guide
    16 pages
    English language
    sale 15% off
ASTM
ASTM D6169/D6169M-21(Guide)
Standard Guide for Selection of Subsurface Soil and Rock Sampling Devices for Environmental and Geotechnical Investigations

SIGNIFICANCE AND USE
4.1 Direct observation of the subsurface by the collection of soil and rock samples is an essential part of investigation for geotechnical and environmental purposes. This guide provides information on the major types of soil and rock sampling devices to assist in selection of devices that are suitable for known site geologic conditions, and provide samples that meet project objectives. This guide should not be used as a substitute for consulting with professional experience in sampling soil or rock in similar formations before determining the best method and type of sampling.  
4.2 This guide should be used in conjunction with Guide D6286 on drilling methods and sampling equipment, and diamond drilling Guide D2113. Drilling and sampler specific practices and guides listed throughout this guide are used as part of developing a detailed site investigation and sampling plan. The sampling plan should start with development of a site conceptual model and phased investigations to locate sampling sites (D420, D6286). The selection of sampling equipment and sampling devices goes hand-in-hand. In some cases, soil sample requirements may influence choice of drilling method, or conversely, types of available sampling equipment may influence choice of sampling devices.  
4.3 Samples should be handled in accordance with Practice D4220/D4220M, for preserving and transporting soil samples, Practice D5079 for preserving and transporting rock core samples for geotechnical purposes. For environmental work sample handling procedures should be in accordance with Practice D6640 for collection and handling of soils obtained in core barrel samplers for environmental investigations, Practice D3694 for preparation of sample containers and for preservation of organic constituents, and Practice D5088 for decontamination of field equipment used at waste sites.
Note 1: The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the...
SCOPE
1.1 This guide covers guidance for the selection of soil and rock sampling devices used for the purpose of characterizing in situ physical and hydraulic properties, chemical characteristics, subsurface lithology, stratigraphy and structure, and hydrogeologic units in geotechnical and environmental investigations.  
1.2 This guide should be used in conjunction with referenced ASTM Guides D420 and D5730, and individual practices for sampling devices referenced in 2.1. Soil and rock samplers are most often used in drilled/pushed boreholes using various drilling methods/technologies in Guide D6286 and it addresses ability to use these samplers.  
1.3 Refer to Practice D6640 and Guide D4547 for handling of samples for environmental investigations. Practices D4220/D4220M and D5079 are used for preserving and transporting soil and rock samples.  
1.4 This guide does not address selection of sampling devices for hand-held soil sampling equipment (Guide D4700) and soil sample collection with solid-stem augering devices (Practice D1452/D1452M), or collection of grab samples or hand-carved block samples (D7015/D7015M) from accessible excavations. Refer to X1.2 for additional guidance on use of soil and rock sampling devices for both environmental and geotechnical applications.  
1.5 This guide does not address devices for collecting cores from submerged sediments or other sampling devices for solid wastes. Refer to Guides D4823 and D6232 for these materials.  
1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.7 This guide offers an organized collection of information or series of options and does not recommend a specific course of action. This document canno...

  • Guide
    28 pages
    English language
    sale 15% off
  • Guide
    28 pages
    English language
    sale 15% off
ASTM
ASTM D6230-21e1(Practice)
Standard Practices for Monitoring Earth or Structural Movement Using Inclinometers

SIGNIFICANCE AND USE
4.1 An inclinometer is a deformation monitoring system, which uses a grooved pipe or casing with internal longitudinal grooves aligned with the anticipated direction of movement, installed in either a soil/rock mass or a geotechnical structural element. The inclinometer casing can be surveyed with a single traversing probe or with an array of in-place inclinometer (IPI) gauges connected to a data logger. The measurement and calculation of deformation normal to the axis of the inclinometer casing is done by passing a probe along the length of this pipe or placement of a sensor array, guided by the internal grooves. The probe or sensor array measures the inclination of the pipe, usually in two orthogonal directions 90° apart (X- and Y-direction) with respect to the axis of the casing (Z-direction, usually the line of gravity). Measurements are converted to distances using trigonometric functions. Successive surveys compared with an initial survey give differences in position and indicate deformation normal to the axis of the inclinometer casing. In most cases the inclinometer casing is installed in a near-vertical hole, and the measurements indicate subsurface horizontal deformation. In some cases, the inclinometer casing is installed horizontally, and the measurements indicate vertical deformation.  
4.2 Inclinometers are also called slope inclinometers or slope indicators. Typical applications include measuring the rate and direction of landslide movement and locating the zone of shearing, monitoring the magnitude and rate of horizontal movements for embankments and excavations, monitoring the settlement and lateral spread beneath tanks and embankments, and monitoring the deflection of bulkheads, piles or structural walls.
Note 1: The precision of this standard is dependent on the competence of the personnel performing it and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of...
SCOPE
1.1 This standard covers the use of inclinometers to monitor the internal movement of ground, or lateral movement of subsurface structures. The standard covers types of instruments, installation procedures, operating procedures, and maintenance requirements. The standard also provides formulae for data reduction.  
1.2 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026 unless superseded by this standard.  
1.2.1 The procedures used to specify how data are collected, recorded or calculated in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analytical methods for engineering design.  
1.3 Units—The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only. Reporting of test results in units other than SI shall not be regarded as nonconformance with this standard.  
1.4 This standard offers an organized collection of information or a series of options and does not recommend a specific course of action. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this standard may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s man...

  • Standard
    11 pages
    English language
    sale 15% off
ASTM
ASTM C1733-21(Test Method)
Standard Test Method for Distribution Coefficients of Inorganic Species by Batch Method

SIGNIFICANCE AND USE
4.1 The distribution coefficient, Kd, is an experimentally determined ratio quantifying the distribution of a chemical species between a given fluid and solid material sample under certain conditions, including the attainment of constant aqueous concentrations of the species of interest. The Kd concept is used in mass transport modeling, for example, to assess the degree to which the movement of a species will be delayed by interactions with the local geomedium as the solution migrates through the geosphere under a given set of underground geochemical conditions (pH, temperature, ionic strength, etc.). The retardation factor (Rf) is the ratio of the velocity of the groundwater divided by the velocity of the contaminant, which can be expressed as:
   where:  
  ρb  =  bulk density of the porous medium (mass/length3), and    ηe  =  effective porosity of the medium (unitless) expressed as a decimal.    
4.2 Because of the sensitivity of Kd to site specific conditions and materials, the use of literature derived  Kd values is strongly discouraged. For applications other than transport modeling, batch Kd measurements also may be used, for example, for parametric studies of the effects of changing chemical conditions and of mechanisms related to the interactions of fluids with solid material.
SCOPE
1.1 This test method covers the determination of distribution coefficients, Kd, of chemical species to quantify uptake onto solid materials by a batch sorption technique. It is a laboratory method primarily intended to assess sorption of dissolved ionic species subject to migration through pores and interstices of site specific geomedia, or other solid material. It may also be applied to other materials such as manufactured adsorption media and construction materials. Application of the results to long-term field behavior is not addressed in this method. Kd for radionuclides in selected geomedia or other solid materials are commonly determined for the purpose of assessing potential migratory behavior of contaminants in the subsurface of contaminated sites and out of a waste form and in the surface of waste disposal facilities. This test method is also applicable to studies for parametric studies of the variables and mechanisms which contribute to the measured Kd.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM D8170-20(Guide)
Standard Guide for Using Disposable Handheld Soil Core Samplers for the Collection and Storage of Soil for Volatile Organic Analysis

SIGNIFICANCE AND USE
5.1 This guide is for the use of disposable handheld soil core samplers in collecting and storing approximately 5 or 25 g soil samples for volatile organic analysis in a manner that reduces loss of contaminants due to volatilization or biodegradation. In general, an initial soil core sample is collected (see Guides D6169/D6169M and D6282/D6282M) and the disposable handheld soil core sampler is then used to collect the 5 or 25 g soil sample from the initial soil core sample. The disposable handheld soil core sampler can also serve as a sample storage chamber.  
5.2 The physical integrity of the soil sample is maintained during sample collection, storage, and transfer in the laboratory for analysis or preservation.  
5.3 During sample collection, storage, and transfer, there is very limited exposure of the sample to the atmosphere.  
5.4 Laboratory subsampling is not required for samples collected following this guide. The sample is expelled directly from the coring body/storage chamber into the appropriate container for analysis, or preservation, at the analytical laboratory without disrupting the integrity of the sample. Subsampling from the disposable handheld soil core sampler should not be performed to obtain smaller sample sizes for analysis.  
5.5 This guide specifies sample storage in the disposable handheld soil core sampler at 4 ± 2°C for up to 48 h.  
5.6 This guide does not use methanol preservation or other chemical preservatives in the field. As a result, there are no problems associated with flammability hazards, shipping restrictions, or dilution of samples containing low volatile concentrations due to solvents being added to samples in the field.  
5.7 The disposable handheld soil core samplers are single-use devices. They should not be cleaned or reused.  
5.8 This disposable handheld soil core samplers cannot be used for collecting cemented material, consolidated material, or material having fragments wider than the mouth of the device or coa...
SCOPE
1.1 This guide is intended for application to soils that may contain volatile organic compounds.  
1.2 This guide provides a general procedure and considerations associated with using a disposable handheld soil core sampler to collect and temporarily store a soil sample for volatile organic analysis.  
1.3 In general, an initial soil sample is collected (see Guides D6169/D6169M and D6282/D6282M) and the disposable handheld soil core sampler is then used to collect the 5 or 25 g soil sample from the initial soil core sample. The disposable handheld soil core sampler can also serve as a sample storage chamber. It is recommended that this standard be used in conjunction with Guides D4547, D4687, D6169/D6169M, D6232, D6282/D6282M, D6418, and D6640, as appropriate, which provide information on the collection of the initial soil core sample.  
1.4 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026. Reporting of test results in units other than SI shall not be regarded as nonconformance with this standard.  
1.5 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process.  
1.6 This standard doe...

  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM D8199-20(Test Method)
Standard Test Method for Determining the Specific Strength of Hydraulically Applied Fiber Matrix Products for Erosion Control

SIGNIFICANCE AND USE
5.1 Specific strength is a measure of the ability of a fiber matrix product to withstand force applied by a tensile machine and is useful to understand in order to produce quality products. Specific strength is frequently related to the matrix density, fiber quality, fiber length and chemistry and can be used as a measurement for quality assurance or quality control, or both requirements.  
5.2 This method may not be applicable to all hydraulically applied fiber matrix products due to variations in product chemistry.
Note 1: The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice D3740 does not in itself assure reliable results. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some of those factors.
SCOPE
1.1 This standard provides a quantitative test method to determine the specific strength of hydraulically applied fiber matrix products using dry and wet preparation methods in a laboratory setting. This method is designed for use as an index test for product quality assurance or quality control, or both to comply with manufacturing requirements. This test method is not indicative of product performance in the field.  
1.2 Units—The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information only and are not considered standard. Reporting of test results in units other than SI shall not be regarded as nonconformance with this standard.  
1.3 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026, unless superseded by this test method.  
1.3.1 The procedures used to specify how data are collected/recorded and calculated in the standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of these test methods to consider significant digits used in analysis methods for engineering data.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6286/D6286M-20(Guide)
Standard Guide for Selection of Drilling and Direct Push Methods for Geotechnical and Environmental Subsurface Site Characterization

SIGNIFICANCE AND USE
4.1 The 1998 edition of this standard was written solely for selection of drilling methods for environmental applications and specifically for installation of groundwater monitoring wells. The second revision was made to include geotechnical applications since many of the advantages, disadvantages, and limitations discussed extensively throughout this document also apply to geotechnical design use such as data collection (sampling and in-situ testing) for construction design and instrumentation. Besides installation of monitoring wells (D5092/D5092M, D6724/D6724M), Environmental investigations are also made for sampling, in-situ testing, and installation of aquifer testing boreholes (D4044/D4044M, D4050).  
4.2 There are other guides for geotechnical investigations addressing drilling methods such as in Eurocode (1, 2)5, U.S. Federal Highway Administration, (3, 4), U.S. Army Corps of Engineers, (5), and U.S. Bureau of Reclamation (6, 7). An authoritative Handbook on Environmental Site Characterization and Ground-Water Monitoring was compiled by Nielsen (8) which addresses drilling methods in detail including the advent of Direct Push methods developed for environmental investigations. Two other major drilling guides have been written by the National Drilling Association (9) and from the Australia Drilling Industry Training Committee (10) and these guides are user for the drillers.  
4.3 Table 1 lists sixteen classes of methods addressed in this guide. The selection of particular method(s) for drilling/push boring requires that specific characteristics of each site be considered. This guide is intended to make the user aware of some of the various drilling/push boring methods available and the applications, advantages, and disadvantages of each with respect to determining geotechnical and environmental exploration. (A) Actual achievable drilled depths will vary depending on the ambient geohydrologic conditions existing at the site and size of drilling/push boring e...
SCOPE
1.1 This guide provides descriptions of various methods for site characterization along with advantages and disadvantages associated with each method discussed. This guide is intended to aid in the selection of drilling method(s) for geotechnical and environmental soil and rock borings for sampling, testing, and installation of wells, or other instrumentation. It does not address drilling for foundation improvement, drinking water wells, or special horizontal drilling techniques for utilities.  
1.2 This guide cannot address all possible subsurface conditions that may occur such as, geologic, topographic, climatic, or anthropogenic. Site evaluation for engineering, design, and construction purposes is addressed in Guide D420. Soil and rock sampling in drill holes is addressed in Guide D6169/D6169M. Pertinent guides and practices addressing specific drilling methods, equipment, and procedures are listed in Section 2. Guide D5730 provides information on most all aspects of environmental site characterization.  
1.3 The values stated in either SI units or inch-pound units (given in brackets) are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.4 This guide does not purport to comprehensively address all methods and the issues associated with drilling for geotechnical and environmental purposes. Users should seek qualified professionals for decisions as to the proper equipment and methods that would be most successful for their site investigation. Other methods may be available for these methods and qualified professionals should have flexibility to exercise judgment as to possible alternatives not covered in this guide. The guide is current at the time of issue, but new alternative methods may become available prior ...

  • Guide
    28 pages
    English language
    sale 15% off
  • Guide
    28 pages
    English language
    sale 15% off
ASTM
ASTM E3242-20(Guide)
Standard Guide for Determination of Representative Sediment Background Concentrations

SIGNIFICANCE AND USE
4.1 Intended Use: This guide may be used by various parties involved in sediment corrective action programs, including regulatory agencies, project sponsors, environmental consultants, toxicologists, risk assessors, site remediation professionals, environmental contractors, and other stakeholders.  
4.2 Related ASTM Standards: This guide is related to Guide E3164, which addresses corrective action monitoring before, during, and after sediment remediation activities; as well as Guide E3163, concerning sediment analytical techniques used during sediment programs.  
4.3 Use of Representative Background to Set a Boundary: Representative background concentrations for sediments can be used to delineate a sediment corrective action, establishing the boundary of the sediment corrective action by distinguishing site-related impacts from representative background concentrations.  
4.4 Use of Representative Background to Establish Cleanup Levels: Representative background concentrations for sediments can also be used to establish cleanup levels for use in sediment corrective actions. In cases where risk-based sediment cleanup levels are below representative background concentrations, background concentrations are typically used as the cleanup level. This ensures that the cleanup levels are sustainable. Any recontamination from ongoing sources will eventually result in surface sediment concentrations greater than the risk-based cleanup level, but the surface sediment should still meet a cleanup level based on representative background concentrations, even after recontamination.  
4.5 Use of Representative Background in Risk Assessments: Representative background concentrations can be used in the risk assessment process (including human and ecological risk assessments) to understand risks posed by background levels of contaminants to human health and the environment, and the incremental risks posed by site-related releases and/or activities that result in sediment concentrat...
SCOPE
1.1 This guide focuses on the approach for determination of representative sediment background concentrations used for remedial actions performed under various regulatory programs, including the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). Although many of the references cited in this guide are CERCLA oriented, the guide is applicable to remedial actions performed under local, state, federal, and international cleanup programs. However, the guide does not describe requirements for each jurisdiction. The requirements for the regulatory entity under which the cleanup is performed should be reviewed to confirm compliance.  
1.2 This guide provides a framework, including specific statistical and geochemical considerations, as well as case studies, demonstrating the approach to determine representative sediment background concentrations. This guide is intended to inform, complement, and support, but not supersede, local, state, federal, or international regulations.  
1.2.1 This guide does not address methods and means of data collection (Guide E3163, Guide E3164.)  
1.2.2 This guide is designed to apply to contaminated sediment sites where sediment data have been collected and are readily available. Additionally, this guide assumes that risk assessments have been performed, so that the contaminants/chemicals of interest that exceed risk-based thresholds have been identified.  
1.2.3 Furthermore, this guide presumes that risk-based thresholds identified are low enough to pose corrective action implementation challenges, and/or the site is subject to recontamination from ongoing anthropogenic and/or natural sources that are not controlled. In both cases, representative sediment background concentrations will be useful for determining the extent of corrective remedial actions (when used as remedial goals), evaluating risks posed by representative background concentrations, and establishing...

  • Guide
    39 pages
    English language
    sale 15% off
ASTM
ASTM D8151-19e1(Practice)
Standard Practice for Obtaining Rainfall Runoff from Unvegetated Rolled and Hydraulic Erosion Control Products (RECPs and HECPs) for Acute Ecotoxicity Testing

SIGNIFICANCE AND USE
5.1 A large number of erosion control product manufacturers produce a variety of RECPs and HECPs that are designed to be applied to any land surface to stabilize soils and prevent erosion. Many of these products are engineered to absorb moisture and remain in place even under extreme rainfall events and are composed of substances that could go into solution with runoff. Based on the characteristics of these products and their intended and actual use in the environment, the most likely scenario through which aquatic organisms would be exposed to these products or their soluble components is through storm water runoff. Further, because such runoff events typically last for minutes to hours rather than days, use of acute (48 h) toxicity testing methodology is appropriate to model expected environment exposures.
Note 1: The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice D3740 does not in itself assure reliable results. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some of those factors.
SCOPE
1.1 This practice establishes the guidelines, requirements, and procedures for obtaining rainfall runoff of unvegetated rolled and hydraulic erosion control products (RECPs and HECPs) during bench-scale conditions from simulated rainfall to be sent out for acute ecotoxicity testing.  
1.2 This practice obtains unvegetated erosion control product (ECP) runoff from rainsplash-induced erosion under bench-scale conditions using bench-scale collection procedures.  
1.3 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.  
1.4 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026, unless superseded by this test method.  
1.4.1 The procedures used to specify how data are collected/recorded and calculated in the standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of these test methods to consider significant digits used in analysis methods for engineering data.  
1.5 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Dev...

  • Standard
    8 pages
    English language
    sale 15% off