37.040.10 - Photographic equipment. Projectors

This document defines terms used in electronic still picture imaging that have not been defined by other ISO/TC 42 standards, Technical Specifications or Technical Reports.

This document provides a uniform basis for determining the exposure times for all types of shutters used in still cameras and contains suitable definitions of the terms used.
It specifies the exposure-time markings for all types of shutters and their tolerances. The characteristics of all types of mechanical shutters, which are mounted in still cameras and affect the control of exposure, motion-stopping ability and synchronization with a photoflash light source are also defined. The tolerances ...view more

This document specifies the method for assigning and reporting ISO speed ratings, ISO speed latitude ratings, standard output sensitivity values, and recommended exposure index values, for digital still cameras. It is applicable to both monochrome and colour digital still cameras.

This document defines the measurement method of optical image stabilization performance for still images compensating for handheld blur consisting of two rotational components, yaw and pitch. It applies to consumer digital cameras with optical image stabilization for still images. Apparatuses such as camcorders and mobile phones with still image shooting functionality are within the scope of this document.

This document specifies a protocol to measure the texture reproduction in images captured and processed by digital cameras including cameras in other devices e.g. in camera phones. This document specifies protocols for the measurement of texture reproduction using test charts with stochastic pattern. NOTE The measurement method specified in this document is for objective evaluations of texture reproduction, of which the results are sometimes inconsistent with subjective evaluations (See Annex C)...view more

This document specifies how to measure and report the shooting time lag, shutter release time lag, shooting rate and start-up time lag for digital still cameras, including camera modules in phones and tablet computers. It includes a method that uses control signals inside the digital still camera and a method that determines the timing values without requiring access to the inside of the digital still camera. This document does not address the measurement either of auto focus speed below recomme...view more

This document provides a uniform basis for determining the exposure times for all types of shutters used in still cameras and contains suitable definitions of the terms used. It specifies the exposure-time markings for all types of shutters and their tolerances. The characteristics of all types of mechanical shutters, which are mounted in still cameras and affect the control of exposure, motion-stopping ability and synchronization with a photoflash light source are also defined. The tolerances s...view more

This document specifies the measurement methods and specification of image quality of lenticular prints that are used for changing images. This document does not cover lenticular prints that are used for 3D images. NOTE Lenticular prints for 3D images can be measured with the same types of procedures. However, it needs more information, such as the dependence of the measurement distance, to evaluate the 3D performance. This document specifically describes measurement methods for cross-talk, view...view more

This document specifies the method for assigning and reporting ISO speed ratings, ISO speed latitude ratings, standard output sensitivity values, and recommended exposure index values, for digital still cameras. It is applicable to both monochrome and colour digital still cameras.

This document specifies a protocol to measure the low-light performance of a camera. It is applicable to the measurement of digital cameras including camera phones and other mobile devices. The performance aspects defined in this document are intended to all be tested. Picking one or some of them by the tester is out of scope of the usage of this document.

ISO 8478:2017 specifies a method for measuring the spectral transmittance of camera lenses. It describes particular conditions for measuring the axial spectral transmittance, over a wavelength range from 350 nm to 700 nm, of camera lenses which are intended to be used mainly for taking pictures of very distant objects. If the spectral transmittance values are used exclusively for the calculation of the ISO colour contribution index (see ISO 6728) throughout ISO 8478:2017, the wavelength range re...view more

ISO 18844:2017 specifies the definition of image flare for digital cameras, test patterns, measurement conditions, and methods, so as to enable the comparison of the results of measurement. The methods of measurement are designed to enable the assessment of the performance of digital cameras by using image data output by the digital cameras. ISO 18844:2017 does not specify the aim values or the allowable range of value for the image flare.

This document specifies methods for measuring the resolution and the SFR of electronic still-picture
cameras. It is applicable to the measurement of both monochrome and colour cameras which output
digital data or analogue video signals.

ISO/TR 17321-3:2017 provides guidelines for user controls and readouts employed in scene-referred capture processing modes implemented in digital cameras and camera raw processing software.

ISO 12233:2017 specifies methods for measuring the resolution and the SFR of electronic still-picture cameras. It is applicable to the measurement of both monochrome and colour cameras which output digital data or analogue video signals.

ISO/TR 19247:2016 is applied to the reliable testing of digital cameras (DSCs).

ISO/TS 17321-4:2016 specifies requirements for a programmable light emission system to produce various spectral radiance distributions intended for DSC colour characterization applications. NOTE 1 Evaluation metrics are described in this part of ISO 17321. These evaluations metrics are intended to provide "Figure of Merit (goodness)" relating to the ability of the device to produce arbitrary spectral power distributions. NOTE 2 This part of ISO 17321 applies to a programmable light emission syst...view more

ISO/TS 19567-1:2016 specifies a protocol to measure the texture reproduction in the images captured and processed by digital cameras including cameras in other devices, e.g. in camera phones. ISO/TS 19567-1:2016 specifies protocols for the measurement of the texture reproduction using test charts with cyclic pattern. ISO/TS 19567-1:2016 excludes the acceptable range of value for texture reproduction.