31.060.01 - Capacitors in general

Specifies marking codes for resistors and capacitors and indexes for the dielectric material and the electrodes of plastic film and paper capacitors

This document describes the methods for testing electrical characteristics of electric
double-layer capacitor cells (hereinafter referred to as "capacitor") used for peak power
assistance in hybrid electric vehicles.
All the tests in this document are type tests.
This document can also be applicable to the capacitor used in idling reduction systems (start
and-stop systems) for the vehicles.
This document can also be applicable to the capacitor modules consisting of more than one
cell.
NO...view more

IEC corrigendum

Specifies marking codes for resistors and capacitors and indexes for the dielectric material and the electrodes of plastic film and paper capacitors

This International Standard states the requirements for both self-healing and non-self-healing continuously rated a.c. capacitors of up to and including 2,5 kVAr, and not less than 0,1 µF, having a rated voltage not exceeding 1 000 V, which are intended for use in discharge lamp circuits operating at 50 Hz or 60 Hz and at altitudes up to 3 000 m. NOTE These lamps and associated ballasts are covered by IEC 60081, IEC 60901, IEC 60188, IEC 60192, IEC 60662, and IEC 61167 and by IEC 61347-2-8 and I...view more

IEC 60063:2015 provides series of preferred values for the resistance of resistors and for the capacitance of capacitors. The definition of such series with a defined numeric resolution is a basic prerequisite for the marking and coding of capacitors and resistors with their respective capacitance or resistance values as described in IEC 60062. This edition includes the following significant technical changes with respect to the previous edition:
- revision of the information on a relationship ...view more

IEC 62146-1:2013 is applicable to grading capacitors used on circuit-breakers. Their function is to control the voltage distribution across the individual interrupter units of a multi-break circuit-breaker. Grading capacitors can also be used in parallel to the interrupter unit on single break circuit-breakers to modify the Transient Recovery Voltage (TRV). The grading capacitor is a sub-component for the circuit-breaker and shall be specified in accordance with the circuit-breaker specification...view more

IEC 62146-1:2013 is applicable to grading capacitors used on circuit-breakers. Their function is to control the voltage distribution across the individual interrupter units of a multi-break circuit-breaker. Grading capacitors can also be used in parallel to the interrupter unit on single break circuit-breakers to modify the Transient Recovery Voltage (TRV). The grading capacitor is a sub-component for the circuit-breaker and shall be specified in accordance with the circuit-breaker specification...view more

This part of IEC 60127 covers requirements for miniature fuse-links for special applications. It does not apply to fuses completely covered by the subsequent parts of IEC 60269-1. It does not apply to miniature fuse-links for appliances intended to be used under special conditions, such as in corrosive or explosive atmospheres. This standard applies in addition to the requirements of IEC 60127-1. This standard is applicable to fuse-links with a rated voltage not exceeding 1000 V, a rated current...view more

This International Standard gives a series of preferred diameters of the finished wire terminations of capacitors and resistors for use in electronic equipment.

This International Standard applies to capacitors and resistors with unidirectional wire terminations intended for use in electronic equipment. This standard provides a method for determination of the space required by capacitors and resistors with unidirectional wire terminations.

IEC 60301:2012 gives a series of preferred diameters of the finished wire terminations of capacitors and resistors for use in electronic equipment. This third edition cancels and replaces the second edition, published in 1971, and its Amendment 1, published in 1972, and constitutes a technical revision. The main technical changes with respect to the second edition are the following:
- employment of SI units only in the normative part of this standard, causing transfer of all imperial dimensions...view more

IEC 60717:2012 applies to capacitors and resistors with unidirectional wire terminations intended for use in electronic equipment. This standard provides a method for determination of the space required by capacitors and resistors with unidirectional wire terminations. NOTE: Instead of measuring the actual space, it may be sufficient to ensure that a component fits into the maximum space for which it is designed. This may be achieved by means of fixed gauges. The main technical changes with resp...view more

This part of IEC 62490 provides the equivalent series inductance L (ESL) measuring method
for capacitors with lead terminal type for use in electronic equipment. The inductance values of capacitors provided for this document are within the range of 1 Nh to 10 nH.

IEC 62490-2:2010 provides the ESL measuring method for the surface mount capacitors for use in electronic equipment.

IEC 62490-1:2010 provides the equivalent series inductance L (ESL) measuring method for capacitors with lead terminal type for use in electronic equipment. The inductance values of capacitors provided for this document are within the range of 1 nH to 10 nH.

IEC 62490-2:2010 provides the ESL measuring method for the surface mount capacitors for use in electronic equipment.

IEC 62490-1:2010 provides the equivalent series inductance L (ESL) measuring method for capacitors with lead terminal type for use in electronic equipment. The inductance values of capacitors provided for this document are within the range of 1 nH to 10 nH.