31.040.01 - Resistors in general
Resistors in general
Widerstande im allgemeinen
Resistances electriques en general
Upori splošno
General Information
TAN - // IEC Corrigendum
- Corrigendum3 pagesEnglish and French language
sale 10% off- e-Library read for1 day
TAN - // IEC Corrigendum
- Corrigendum3 pagesEnglish and French language
sale 10% off- e-Library read for1 day
Specifies marking codes for resistors and capacitors and indexes for the dielectric material and the electrodes of plastic film and paper capacitors
- Amendment7 pagesEnglish language
sale 10% off- e-Library read for1 day
Resistance measurements are typically compromised by a variety of phenomena, for example
serial resistance in the measurement path, self-heating or non-ohmic properties. Whether the
effect of such phenomena on a resistance measurement is acceptable or not depends on the
magnitude of each effect in comparison to the resistance and to the required accuracy. Hence,
the risk of erroneous resistance measurements increases with decreasing resistance and with
a tightening of the permissible tolera...view more
- Standard48 pagesEnglish language
sale 10% off- e-Library read for1 day
IEC 62812:2019 specifies methods of measurement and associated test conditions that eliminate or reduce the influence of adverse phenomena in order to improve the attainable accuracy of low-resistance measurements. The methods described in this document are applicable for the individual measurements of the resistance of individual resistors, and also for resistance measurements as part of a test sequence. They are applied if prescribed by a relevant component specification, or if agreed between ...view more
- Standard48 pagesEnglish language
sale 10% off- e-Library read for1 day
IEC 62812:2019 specifies methods of measurement and associated test conditions that eliminate or reduce the influence of adverse phenomena in order to improve the attainable accuracy of low-resistance measurements. The methods described in this document are applicable for the individual measurements of the resistance of individual resistors, and also for resistance measurements as part of a test sequence. They are applied if prescribed by a relevant component specification, or if agreed between ...view more
- Standard92 pagesEnglish and French language
sale 15% off
IEC corrigendum
- Corrigendum5 pagesEnglish language
sale 10% off- e-Library read for1 day
Specifies marking codes for resistors and capacitors and indexes for the dielectric material and the electrodes of plastic film and paper capacitors
- Standard33 pagesEnglish language
sale 10% off- e-Library read for1 day
IEC 60063:2015 provides series of preferred values for the resistance of resistors and for the capacitance of capacitors. The definition of such series with a defined numeric resolution is a basic prerequisite for the marking and coding of capacitors and resistors with their respective capacitance or resistance values as described in IEC 60062. This edition includes the following significant technical changes with respect to the previous edition:
- revision of the information on a relationship ...view more
- Standard20 pagesEnglish and French language
sale 15% off
This International Standard gives a series of preferred diameters of the finished wire terminations of capacitors and resistors for use in electronic equipment.
- Standard8 pagesEnglish language
sale 10% off- e-Library read for1 day
Non-linearity testing is a method to evaluate the integrity of a resistive element. It may be applied as an effective inline screening method suitable to detect and eliminate potential infant mortality failures in passive components. The method is fairly rapid, convenient, and the associated equipment is relatively inexpensive. Typical effects causing non-linearity on resistors are e.g. inhomogeneous spots within a resistive film, traces of film left in the spiraling grooves, or contact instabil...view more
- Standard19 pagesEnglish language
sale 10% off- e-Library read for1 day
Standardizes a method of measurement and associated test conditions for determining the magnitude of non-linear distortion generated in a resistor. Has the status of a technical report. The contents of the corrigendum of September 1974 have been included in this copy.
- Standard19 pagesEnglish language
sale 10% off- e-Library read for1 day
This International Standard applies to capacitors and resistors with unidirectional wire terminations intended for use in electronic equipment. This standard provides a method for determination of the space required by capacitors and resistors with unidirectional wire terminations.
- Standard13 pagesEnglish language
sale 10% off- e-Library read for1 day
IEC 60440:2012 specifies a method of measurement and associated test conditions to assess the magnitude of non-linear distortion generated in a resistor. This method is applied if prescribed by a relevant component specification, or if agreed between a customer and a manufacturer. This International Standard cancels and replaces the Technical Report IEC/TR 60440, published in 1973. The major changes with regard to the Technical Report are:
- change of the principle parameter's term from "third ...view more
- Standard33 pagesEnglish and French language
sale 15% off
IEC 60301:2012 gives a series of preferred diameters of the finished wire terminations of capacitors and resistors for use in electronic equipment. This third edition cancels and replaces the second edition, published in 1971, and its Amendment 1, published in 1972, and constitutes a technical revision. The main technical changes with respect to the second edition are the following:
- employment of SI units only in the normative part of this standard, causing transfer of all imperial dimensions...view more
- Standard12 pagesEnglish and French language
sale 15% off
IEC 60717:2012 applies to capacitors and resistors with unidirectional wire terminations intended for use in electronic equipment. This standard provides a method for determination of the space required by capacitors and resistors with unidirectional wire terminations. NOTE: Instead of measuring the actual space, it may be sufficient to ensure that a component fits into the maximum space for which it is designed. This may be achieved by means of fixed gauges. The main technical changes with resp...view more
- Standard20 pagesEnglish and French language
sale 15% off
IEC 60915:2006 contains preferred dimensions for shaft ends and bushes and for the mounting of single-hole, bush-mounted, shaft-operated variable capacitors, variable resistors and potentiometers. If other dimensions not listed in this standard have to be used, it is recommended to select them also from IEC 60390 and IEC 60620. This second edition cancels and replaces the first edition published in 1987 and constitutes a minor revision, related to tables, figures and references. This bilingual v...view more
- Standard31 pagesEnglish and French language
sale 15% off
specifies marking codes for resistors and capacitors and indexes for the dielectric material and the electrodes of plastic film and paper capacitors
- Standard18 pagesEnglish language
sale 10% off- e-Library read for1 day
EN following parallel vote * Supersedes HD 91 S1:1977
- Standard23 pagesEnglish language
sale 10% off- e-Library read for1 day