03.120.01 - Quality in general

IEC 61163-2 provides guidance on RSS techniques and procedures for electrical,electronic, and mechanical components. This document is procedural in nature and is not, andcannot be, exhaustive with respect to component technologies due to the rapid rate ofdevelopments in the component industry.This document is:a) intended for component manufacturers as a guideline;b) intended for component users as a guideline to negotiate with component manufacturers onRSS requirements;c) intended to allow the p...view more

IEC 62960:2020 provides guidance on a review methodology for dependability from a technical perspective that is applicable at all stages of a system life cycle. Its application can improve the dependability of a system throughout its life cycle by triggering appropriate actions at appropriate times to address potential dependability problems.
It provides guidance for developers, manufacturers, users and third-party independent reviewers such as consulting organizations.
This document describes...view more

IEC 61163-2:2020 provides guidance on RSS techniques and procedures for electrical, electronic, and mechanical components. This document is procedural in nature and is not, and cannot be, exhaustive with respect to component technologies due to the rapid rate of developments in the component industry. This document is:
a) intended for component manufacturers as a guideline;
b) intended for component users as a guideline to negotiate with component manufacturers on RSS requirements;
c) intende...view more

EN-IEC 61123 is intended to define a procedure to verify if a reliability of an item/system complies with the stated requirements. The requirement is assumed to be specified as the percentage of success (success ratio) or the percentage of failures (failure ratio). This document can be used where a number of items are tested (number of trials performed) and classified as passed or failed. It can also be used where one or a number of items are tested repeatedly. The procedures are based on the as...view more

IEC 61123:2019 is intended to define a procedure to verify if a reliability of an item/system complies with the stated requirements. The requirement is assumed to be specified as the percentage of success (success ratio) or the percentage of failures (failure ratio). This document can be used where a number of items are tested (number of trials performed) and classified as passed or failed. It can also be used where one or a number of items are tested repeatedly. The procedures are based on the ...view more

IEC 61123:2019 is intended to define a procedure to verify if a reliability of an item/system complies with the stated requirements. The requirement is assumed to be specified as the percentage of success (success ratio) or the percentage of failures (failure ratio). This document can be used where a number of items are tested (number of trials performed) and classified as passed or failed. It can also be used where one or a number of items are tested repeatedly. The procedures are based on the ...view more

IEC 62629-12-2:2019 specifies the measuring methods of motion artifacts for stereoscopic displays using glasses. This document is applicable to stereoscopic displays using glasses, which consist of transmissive type active matrix liquid crystal display modules (without a post image processing).

This document specifies requirements that enable an organization to design, develop and provide products, goods or services so that they can be accessed, understood and used by the widest range of users.
This document specifies requirements and recommendations that enables  an organization to extend their range of users by identifying diverse needs, characteristics, capabilities,  and preferences, by directly or indirectly involving users, and by using knowledge about accessibility in its proce...view more

This standard establishes requirements for performing and documenting APQP and PPAP. APQP begins
with conceptual product needs and extends through product definition, production planning, product
and process validation (i.e. PPAP), product use, and post-delivery service. This standard integrates and
collaborates with the requirements of the EN 9100, EN 9102, EN 9103 and EN 9110 standards.
The requirements specified in this standard are complementary (not alternative) to contractual and
appl...view more

This document explains how failure modes and effects analysis (FMEA), including the failure
modes, effects and criticality analysis (FMECA) variant, is planned, performed, documented
and maintained.
The purpose of failure modes and effects analysis (FMEA) is to establish how items or
processes might fail to perform their function so that any required treatments could be
identified. An FMEA provides a systematic method for identifying modes of failure together
with their effects on the item...view more

This document provides guidance in relation to a set of requirements placed upon system life
cycles in order for an open system to achieve open systems dependability.
This document elaborates on IEC 60300-1 by providing details of the changes needed to
accommodate the characteristics of open systems. It defines process views based on
ISO/IEC/IEEE 15288:2015, which identifies the set of system life cycle processes.
This document is applicable to life cycles of products, systems, processes or...view more

IEC 60812:2018 explains how failure modes and effects analysis (FMEA), including the failure modes, effects and criticality analysis (FMECA) variant, is planned, performed, documented and maintained. The purpose of failure modes and effects analysis (FMEA) is to establish how items or processes might fail to perform their function so that any required treatments could be identified. An FMEA provides a systematic method for identifying modes of failure together with their effects on the item or p...view more

ISO/IEC 80079-34:2018 specifies particular requirements and information for establishing and maintaining a quality management system to manufacture Ex Products in accordance with the certificates. While it does not preclude the use of other quality management systems that are compatible with the objectives of ISO 9001:2015 and which provide equivalent results, the minimum requirements are given in this document. This second edition cancels and replaces the first edition, published in 2011, and c...view more

IEC 60812:2018 explains how failure modes and effects analysis (FMEA), including the failure modes, effects and criticality analysis (FMECA) variant, is planned, performed, documented and maintained. The purpose of failure modes and effects analysis (FMEA) is to establish how items or processes might fail to perform their function so that any required treatments could be identified. An FMEA provides a systematic method for identifying modes of failure together with their effects on the item or p...view more

IEC 62853:2018 provides guidance in relation to a set of requirements placed upon system life cycles in order for an open system to achieve open systems dependability. This document elaborates on IEC 60300-1 by providing details of the changes needed to accommodate the characteristics of open systems. It defines process views based on ISO/IEC/IEEE 15288:2015, which identifies the set of system life cycle processes. This document is applicable to life cycles of products, systems, processes or ser...view more

The objective of any organization, as part of continual improvement, is to reduce the number of issues
(i.e. undesirable conditions, defects, failures) and to minimize their impact on quality, delivery
performance, and cost.
This includes having processes in place to detect and eradicate significant and recurrent issues, which
implies having well identified problems, a common understanding of their impact and associated root
causes, and having defined and implemented adequate actions so tha...view more

This Standard defines the dependability assurance programme and the dependability requirements for space systems.
Dependability assurance is a continuous and iterative process throughout the project life cycle.
The ECSS dependability policy for space projects is applied by implementing a dependability assurance programme, which comprises:
•   identification of all technical risks with respect to functional needs which can lead to non-compliance with dependability requirements,
•   application of an...view more

The part 1 of EN 50126
* considers RAMS, understood as reliability, availability, maintainability and safety and their interaction;
* considers the generic aspects of the RAMS life-cycle. The guidance in this part is still applicable in the application of specific standards;
* defines
- a process, based on the system life-cycle and tasks within it, for managing RAMS;
- a systematic process, tailorable to the type and size of system under consideration, for specifying requirements for RAMS a...view more

Part 2 of EN 50126
* considers the safety-related generic aspects of the RAMS life-cycle. The guidance in this part is still applicable in the application of specific standards;
* defines methods and tools which are independent of the actual technology of the systems and subsystems;
* provides:
- the user of the standard with the understanding of the system approach to safety which is a key concept of EN 50126;
- methods to derive the safety requirements and their safety integrity requireme...view more

ISO/IEC 25064:2013 describes the Common Industry Format (CIF) for user needs reports, and provides specifications for their contents and format, including the content elements to be provided. User needs reports include both the collection and documentation of information from various sources relevant to user needs, and the analysis and integration of this information into consolidated user needs.
User needs reports are applicable to software and hardware systems, products or services (excludin...view more