CEN/TC 256/SC 2/WG 35 - Hot box detection

This part of EN 15437 defines the minimum characteristics for the interface between a trackside Hot Axlebox Detector (HABD) and Rolling Stock (RST) that comply with the European Directives for Interoperability to ensure that the minimum functional requirement of the interface is achieved.
The minimum requirements of the interface apply to:
a)   Rolling stock conforming to standard European railway gauge, that is 1 435 mm;
b)   Rolling stock axles fitted with outboard bearings;
NOTE 1   The design of rolling stock axles fitted with inboard bearings should respect the requirements set out in Note 2 of 5.2.
c)   Rolling stock with a maximum design speed lower than 250 km/h;
NOTE 2   Interoperable rolling stock with a maximum design speed higher than or equal to 250 km/h are mandated to have on-board equipment for axlebox condition monitoring. The requirements for on-board equipment are described in !EN 15437-2:2012+A1:2022.
NOTE 3   Interoperable rolling stock with a maximum design speed higher than or equal to 250 km/h are outside the scope of this Part of the standard. However, if such rolling stock are required to be monitored by HABDs their target area should comply with the requirements specified in this standard, except where stated otherwise.
d)   Trackside HABDs that are required to monitor rolling stock with a maximum design speed higher than or equal to 250 km/h.
The rolling stock requirements of the interface are described in Clause 5 and for the HABD requirements of the interface are described in Clause 6.
The scope of this part (part 1) of the standard does not include:
-   Hot Wheel (Hot Disc) Detectors (HWDs). However, HWD are often installed in combination with trackside HABD to provide a dual monitoring system. This standard does not prevent the use of such a combination;
-   how a HABD measures the temperature and identifies axle box position. This is part of an individual equipment design and not part of the functional requirements of this standard;
-   operational requirements for acting on the information reported by the HABD system;
-   maintenance requirements for HABD systems.

This European Standard defines the minimum performance requirements of on-board monitoring systems for axlebox condition monitoring by means of temperature measurements.
This European Standard refers to temperature monitoring of the axlebox. However, the design may be such that the rolling bearing itself is monitored directly.
The requirements of this European Standard are intended to apply equally to basic monitoring systems for monitoring the axlebox temperature through to more technically complex systems that may employ a combination of mechatronics.
To ensure the compatibility of monitoring systems and the effective monitoring functions, this European Standard defines the requirements in the following areas:
-   equipment and characteristics;
-   monitoring performance;
-   operation and interface.
This part of EN 15437 does not include:
-   systems that do not give an indication to the driver;
-   how an on-board monitoring system is structured and how it measures the temperature and identifies axlebox position. This is considered part of equipment design and not part of the functional requirements set out in this standard;
-   operational requirements for acting on the information reported by the on-board monitoring system;
-   operational requirements for conflict of information between trackside monitoring systems and on-board monitoring systems;
-   maintenance requirements for on-board temperature monitoring systems.

This European Standard defines the minimum performance requirements of on-board monitoring systems for axlebox condition monitoring by means of temperature measurements.
This European Standard refers to temperature monitoring of the axlebox. However, the design may be such that the rolling bearing itself is monitored directly.
The requirements of this European Standard are intended to apply equally to basic monitoring systems for monitoring the axlebox temperature through to more technically complex systems that may employ a combination of mechatronics.
To ensure the compatibility of monitoring systems and the effective monitoring functions, this European Standard defines the requirements in the following areas:
-   equipment and characteristics;
-   monitoring performance;
-   operation & Interface.
This part of EN 15437 does not include:
-   systems that do not give an indication to the driver;
-   how an on-board monitoring system is structured and how it measures the temperature and identifies axlebox position. This is considered part of equipment design and not part of the functional requirements set out in this standard;
-   operational requirements for acting on the information reported by the on-board monitoring system;
-   operational requirements for conflict of information between trackside monitoring systems and on-board monitoring systems;
-   maintenance requirements for on-board temperature monitoring system.

This part of EN15437 defines the minimum characteristics for the interface between a trackside Hot Axlebox Detector (HABD) and Rolling Stock (RST) that comply with the European Directives for Interoperability to ensure that the minimum functional requirement of the interface is achieved.  
The minimum requirements of the interface apply to:
a)   Rolling stock conforming to standard European railway gauge, that is 1435mm;
b)   Rolling stock axles fitted with outboard bearings;
NOTE   The design of rolling stock axles fitted with inboard bearings should respect the requirements set out in Note 2 of 5.2.
c)   Rolling stock with a maximum operational speed of up to and including 250 km/h;
NOTE 1   That is conventional rail and class 2 high speed rail rolling stock as defined in the rolling stock TSIs.
NOTE 2   Interoperable rolling stock designed for speeds above 250km/h (class 1 high speed rolling stock) are mandated to have on-board equipment for axlebox condition monitoring. The requirements for on-board equipment are described in part 2 of this standard which is currently under development.
NOTE 3   Interoperable rolling stock designed for speeds above 250km/h (class 1 high speed rolling stock) are outside the scope of this Part of the standard. However, if class 1 high speed trains are required to be monitored by HABDs their target area should comply with the requirements specified in this standard, except where stated otherwise.
d)   Trackside HABDs that are required to monitor conventional rail and class 2 high speed rail rolling stock.
The rolling stock requirements of the interface are described in Clause 5 and for the HABD requirements of the interface are described in Clause 6.