CEN/TC 155/WG 10 - Systems for non-pressure drainage and sewerage - PE (solid wall)

This Technical Report gives guidance for the assessment of conformity of materials, products and assemblies in accordance with the applicable part(s) of EN 1451 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of third-party certification procedures.
NOTE 1   It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001 [1].
NOTE 2   If third-party certification is involved, it is recommended that the certification body is accredited to EN 45011 [2], EN 45012 [3] or EN ISO/IEC 17021 [4], as applicable.
In conjunction with EN 1451-1 this document is applicable to piping systems made of polypropylene (PP) intended to be used for:
-   inside buildings (marked with "B");
-   for both inside buildings and buried in ground within the building structure (marked with "BD").

This Technical Report gives guidance for the assessment of conformity of materials, products and assemblies in accordance with the applicable part(s) of EN 1519 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of third-party certification procedures.
NOTE 1   It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001 [1].
NOTE 2   If third-party certification is involved, it is recommended that the certification body is accredited to EN 45011 [2], EN 45012 [3] or EN ISO/IEC 17021 [4], as applicable.
In conjunction with EN 1519-1 this document is applicable to piping systems made of polyethylene (PE) intended to be used for:
-   inside buildings (marked with "B");
-   for both inside buildings and buried in ground within the building structure (marked with "BD").

This Part of EN 12666 specifies the requirements for pipes, fittings and the system of polyethylene (PE) piping systems intended to be used for  -  non-pressure underground drainage and sewerage outside the building structure (application area code "U"), and -  non-pressure underground drainage and sewerage for both buried in the ground within the building structure (application area code "D") and outside the building structure. This is reflected in the marking of products by "U" and "UD". It also specifies the test parameters for the test methods referred to in this European Standard. This European Standard covers a range of nominal sizes, a range of pipe series/stiffness classes and gives recommendations concerning colours. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. In conjunction with CEN/TS 12666-2 [1] it is applicable to PE pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure drainage and sewerage.This European Standard is applicable to PE pipes with or without an integral socket. The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings. This European Standard is applicable to PE pipes and fittings for the following types of joints: - elastomeric ring seal joints; - butt fused joints; - electrofusion joints; - mechanical joints. NOTE 2 Requirements and limiting values for application area code "D" are given in Tables 3, 6 and Table 12. NOTE 3 Pipes, fittings and other components conforming to any of the plastics product standards listed in the bibliography may be used with pipes and fittings conforming to this European Standard, provided they conform to the requirements for joint dimensions given in Clause 6

This Technical Specification gives guidance for the assessment of conformity of materials, products, joints and assemblies in accordance with the applicable part(s) of EN 1519 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of third-party certification procedures.
NOTE 1   It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001 [1].
NOTE 2   If third-party certification is involved, it is recommended that the certification body is accredited to EN 45011 [2], EN 45012 [3] or EN ISO/IEC 17021 [4], as applicable.
NOTE 3   In order to help the readers, a summary of the test regime is given in Annex A.
In conjunction with EN 1519-1 this document is applicable to piping systems made of polyethylene (PE) intended to be used:
- for soil and waste discharge systems (low and high temperature) inside buildings (application area code "B") and,
- for soil and waste discharge systems (low and high temperature) for both inside buildings and buried in ground within the building structure (application area code "BD")
This is reflected in the marking of products by "B" or "BD".

This Technical Specification gives guidance for the assessment of conformity of materials, products, joints and assemblies in accordance with the applicable part(s) of EN 1852 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE   In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with EN 1852-1 this document is applicable to solid wall piping systems made of polypropylene (PP) intended to be used for:
- non-pressure underground drainage and sewerage outside the building structure (application area code "U"), and
- non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code "D") and outside the building structure.
This is reflected in the marking of products by "U" and "UD".

This Technical Specification gives guidance for the assessment of conformity of materials, products, joints and assemblies in accordance with the applicable part(s) of EN 1451 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of third-party certification procedures.
NOTE 1   It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001 [1].
NOTE 2   If third-party certification is involved, it is recommended that the certification body is accredited to EN 45011 [2], EN 45012 [3] or EN ISO/IEC 17021 [4], as applicable.
NOTE 3   In order to help the readers, a summary of the test regime is given in Annex A.
In conjunction with EN 1451-1 this document is applicable to piping systems made of polypropylene (PP) intended to be used:
- for soil and waste discharge systems (low and high temperature) inside buildings (application area code "B") and,
- for soil and waste discharge systems (low and high temperature) for both inside buildings and buried in ground within the building structure (application area code "BD")
This is reflected in the marking of products by "B" or "BD".

This standard specifies the requirements for pipes, fittings and the system of polyethylene (PE) solid-wall piping systems in the field of soil and waste discharge - inside buildings (marked with "B") and - for both inside buildings and buried in ground within the building structure (marked with "BD"). It also specifies the test parameters for the test methods referred to in this standard.

This part of EN 1852 specifies the requirements for solid wall pipes, fittings and the system of polypropylene (PP) piping systems intended for use for:
   non-pressure underground drainage and sewerage outside the building structure (application area code "U"), and
   non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code "D") and outside the building structure.
This is reflected in the marking of products by "U" and "UD".
This standard covers PP materials without mineral modifiers.
It also specifies the test parameters for the test methods referred to in this standard.
This standard covers a range of nominal sizes, and pipe series and gives recommendations concerning colours.
NOTE 1   It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
In conjunction with Part 2 and Part 3 of EN 1852 it is applicable to PP pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage.
This standard is applicable to PP pipes and fittings with or without an integral socket.
NOTE 2   The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings.
NOTE 3   Requirements and limiting values for application area code "D" are given in Table 3, Table 7 and Table 14.
NOTE 4   Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex C can be connected to pipes and fittings conforming to this standard, when they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 14.

This standard specifies the requirements of pipes, fittings and the system of polypropylene (PP) for solid-wall piping systems in the field of soil and waste discharge (low and high temperature)  (inside buildings (marked with "B"); and  (both inside buildings and buried in ground within the building structure (marked with "BD").  NOTE 1: The application area "inside buildings" according to this standard, applies to the interior area of the building only. The application area "within the building structure" conforms to the requirements for "inside buildings" according to prEN 12056-1.

This European Technical Specification gives guidance for the assessment of conformity to be included in the manufacturer's quality plan as part of the quality system.
This Technical Specification includes:
a)   requirements for materials, components, joints and assemblies given in EN 14758-1;
b)   requirements for the manufacturer's quality system;
NOTE 1   It is recommended that the quality system conforms to EN ISO 9001 [1].
c)   definitions and procedures to be applied if third party certification is involved.
NOTE 2   If third party certification is involved, it is recommended that the certification body is accredited to EN 45011 [2] or EN 45012 [3], as applicable.
This Technical Specification is applicable to piping systems made of polypropylene (PP-MD) intended to be used for
   non pressure underground drainage and sewerage outside building structures (application area code "U"), reflected in the marking of products by "U"; and
non pressure underground drainage and sewerage for both buried in the ground within the building structure (application area code "D") and outside the building structure (application area code "U"), reflected in the marking of products by "UD".

This standard specifies a method for determining the flow rate/pressure drop relationship of components for plastics piping when tested using air at 25 mbar.It is applicable to mechanical fittings, valves, tapping tees and other ancil- laries intended to be used in polyethylene (PE) piping systems for supply of gaseous fuels. The data obtained may be used to calculate the flow of such gases for a specified pressure drop.

This Technical Specification, together with ENV 1046 and EN 1610, provides a material-specific set of guidelines for the installation of piping systems made of polypropylene with mineral modifier(s) (PP-MD) in the field of non-pressure underground drainage and sewerage.
-   outside the building structure (application area code "U");
-   both buried in ground within the building structure (application area code "D") and outside the building.
This is reflected in the marking of products by "U" and "UD".

This Part of EN 12666 gives guidance for the assessment of conformity to be included in the manufacturer's quality plan as part of the quality system.
This Technical Specification includes:
a)    requirements for materials, components, joints and assemblies given in EN 12666-1;
b)    requirements for the manufacturer's quality system;
NOTE 1   It is recommended that the quality system conforms to EN ISO 9001:2000[1].
c)    definitions and procedures to be applied if third party certification is involved.
NOTE 2   If third party certification is involved, it is recommended that the certification body is accredited to EN 45011[2] or EN 45012[3], as applicable.
It is applicable to piping systems made of polyethylene (PE) in the field of non pressure underground drainage and sewerage outside the building structure (application area code "U") and for non pressure underground drainage and sewerage for both buried in the ground within the building structure (application area code "D") and outside the building structure. This is reflected in the marking of products by "U"and "UD".

This Part of EN 1455 gives guidance for the assessment of conformity to be included in the manufacturer's
quality plan as part of the quality system.
This prestandard includes:
a) requirements for materials, components, joints and assemblies given in EN 1455-1:1999;
b) requirements for the manufacturer's quality system;
    NOTE 1 It is recommended that the quality system conforms to EN ISO 9001, as applicable.
c) definitions and procedures to be applied if third party certification is involved.
    NOTE 2  If third party certification is involved, it is recommended that the certification body is accredited
    to EN 45011 or EN 45012, as applicable.
This Part of EN 1455 is applicable to solid-wall piping systems made of acrylonitrile-butadiene-styrene (ABS) in
the field of soil and waste discharge (low and high temperature)
    inside buildings (application area code "B") and
    inside buildings and buried in ground within the building structure (application area code "BD").

This Part of EN 1566 gives guidance for the assessment of conformity to be included in the manufacturer's
quality plan as part of the quality system.
This prestandard includes:
a) requirements for materials, components, joints and assemblies given in EN 1566-1;
b) requirements for the manufacturer's quality system;
    NOTE 1 It is recommended that the quality system conforms to EN ISO 9001, as applicable.
c) definitions and procedures to be applied if third party certification is involved.
    NOTE 2  If third party certification is involved, it is recommended that the certification body is accredited
    to EN 45011 or EN 45012, as applicable.
This Part of EN 1566 is applicable to solid-wall piping systems made of chlorinated poly(vinyl chloride) (PVC-C)
in the field of soil and waste discharge (low and high temperature)
- inside buildings (application area code "B") and
- inside buildings and buried in ground within the building structure (application area code "BD").

This Part of EN 1565 gives guidance for the assessment of conformity to be included in the manufacturer's
quality plan as part of the quality system.
This prestandard includes:
a) requirements for materials, components, joints and assemblies given in  EN 1565-1:1998;
b) requirements for the manufacturer's quality system;
    NOTE 1 It is recommended that the quality system conforms to EN ISO 9001, as applicable.
c) definitions and procedures to be applied if third party certification is involved.
    NOTE 2 If third party certification is involved, it is recommended that the certification body is accredited
    to EN 45011 or EN 45012, as applicable.
This Part of EN 1565 is applicable to solid-wall piping systems made of styrene copolymer blends (SAN+PVC)
in the field of soil and waste discharge (low and high temperature)
- inside buildings (application area code "B") and
- inside buildings and buried in ground within the building structure (application area code "BD").

This European Standard specifies the requirements for solid-wall pipes, fittings and the system of piping systems made from mineral modified polypropylene materials (PP-MD) in the field of non-pressure underground drainage and sewerage outside the building structure (application area code "U"), and non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code "D") and outside the building structure.
This is reflected in the marking of products by "U" and "UD".
It also specifies the test parameters for the test methods referred to in this European Standard.
This European Standard covers a range of nominal sizes, a range of pipe series/stiffness classes and gives recommendations concerning colours.
NOTE 1   It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
In conjunction with Part 2 and Part 3 of EN 14758 (see Foreword) it is applicable to PP-MD pipes and fittings, their elastomeric sealing ring joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage.
This European Standard is applicable to PP-MD pipes with or without an integral socket.
NOTE 2   The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings.
NOTE 3   Requirements and limiting values for application area code "D" are given in Table 4, Table 7 and Table 13.
NOTE 4   Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this European Standard, when they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 13.

This Part of EN 1451 gives guidance for the assessment of conformity to be included in the manufacturer's
quality plan as part of the quality system.
This prestandard includes:
a) requirements for materials, components, joints and assemblies given in  EN 1451-1;
b) requirements for the manufacturer's quality system;
    NOTE 1  It is recommended that the quality system conforms to EN ISO 9001, as applicable.
c) definitions and procedures to be applied if third party certification is involved.
    NOTE 2  If third party certification is involved, it is recommended that the certification body is accredited
    to EN 45011 or EN 45012, as applicable.
This Part of EN 1451 is applicable to solid-wall piping systems made of polypropylene (PP) in the field of soil and
waste discharge (low and high temperature)
- inside buildings (application area code "B") and
- inside buildings and buried in ground within the building structure (application area code "BD").

This Part of EN 1519 gives guidance for the assessment of conformity to be included in the manufacturer's
quality plan as part of the quality system.
This prestandard includes:
a) requirements for materials, components, joints and assemblies given in  EN 1519-1:1999;
b) requirements for the manufacturer's quality system;
    NOTE 1  It is recommended that the quality system conforms to EN ISO 9001, as applicable.
c) definitions and procedures to be applied if third party certification is involved.
    NOTE 2  If third party certification is involved, it is recommended that the certification body is accredited
    to EN 45011 or EN 45012, as applicable.
This Part of EN 1519 is applicable to solid-wall piping systems made of polyethylene (PE) in the field of soil and
waste discharge (low and high temperature)
- inside buildings (application area code "B") and
- inside buildings and buried in ground within the building structure (application area code "BD").

This Part of EN 12666 specifies the requirements for pipes, fittings and the system of polyethylene (PE) piping systems intended to be used for
   non pressure underground drainage and sewerage outside the building structure (application area code "U"), and
                non pressure underground drainage and sewerage for both buried in the ground within the building structure (application area code "D") and outside the building structure.
This is reflected in the marking of products by "U" and "UD".
It also specifies the test parameters for the test methods referred to in this European Standard.
This European Standard covers a range of nominal sizes, a range of pipe series/stiffness classes and gives recommendations concerning colours.
NOTE 1    It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
In conjunction with CEN/TS 12666-2 [1] and CEN/TS 12666-3 [2] it is applicable to PE pipes and fittings, their joints and to joints with components of other plastics and non plastics materials intended to be used for buried piping systems for non pressure drainage and sewerage.
This European Standard is applicable to PE pipes with or without an integral socket.
The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings.
This European Standard is applicable to PE pipes and fittings for the following types of joints:
   elastomeric ring seal joints;
   butt fused joints;
   electrofusion joints;
   mechanical joints.
(continued)

This Part of prEN 1555 specifies the characteristics of valves, made of polyethylene (PE) for piping systems in the field of the supply of gaseous fuels. NOTE:Valves made from other material than polyethylene designed for the supply of gaseous fuels conforming to the relevant standards are permitted to be used in PE piping system according to prEN 1555 provided they have relevant PE connection for butt fusion or electrofusion ends (see prEN 1555-3:1999). It also specifies the test parameters for the tests methods referred to in the present standard.