SIST EN 62575-1:2016

SLOVENSKI STANDARD
SIST EN 62575-1:2016
01-april-2016
5DGLRIUHNYHQþQLILOWUL5)]D]HORYLVRNH]YRþQHIUHNYHQFH%$:GRORþHQH
NDNRYRVWLGHO6SORãQDVSHFLILNDFLMD
Radio frequency (RF) bulk acoustic wave (BAW) filters of assessed quality - Part 1:
Generic specification
Ta slovenski standard je istoveten z: EN 62575-1:2016
ICS:
33.120.30 5DGLRIUHNYHQþQLNRQHNWRUML RF connectors
5)
SIST EN 62575-1:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 62575-1:2016

---------------------- Page: 2 ----------------------

SIST EN 62575-1:2016


EUROPEAN STANDARD EN 62575-1

NORME EUROPÉENNE

EUROPÄISCHE NORM
February 2016
ICS 31.140

English Version
Radio frequency (RF) bulk acoustic wave (BAW) filters of
assessed quality - Part 1: Generic specification
(IEC 62575-1:2015)
Filtres radiofréquences (RF) à ondes acoustiques de Volumenwellen-(BAW-)Filter mit bewerteter Qualität für
volume (OAV) sous assurance de la qualité - Hochfrequenz-(HF-)Anwendungen -
Partie 1: Spécification générique Teil 1: Fachgrundspezifikation
(IEC 62575-1:2015) (IEC 62575-1:2015)
This European Standard was approved by CENELEC on 2015-12-03. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 62575-1:2016 E

---------------------- Page: 3 ----------------------

SIST EN 62575-1:2016
EN 62575-1:2016
European foreword
The text of document 49/1163/FDIS, future edition 1 of IEC 62575-1, prepared by
IEC/TC 49 “Piezoelectric, dielectric and electrostatic devices and associated materials for frequency
control, selection and detection" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 62575-1:2016.

The following dates are fixed:
• latest date by which the document has to be (dop) 2016-09-03
implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2018-12-03
• latest date by which the national
standards conflicting with the
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.

Endorsement notice
The text of the International Standard IEC 62575-1:2015 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:

IEC 60368 Series NOTE Harmonized as EN 60368 Series.
IEC 60862-1:2015 NOTE Harmonized as EN 60862-1:2015 (not modified).
IEC 61000-4-2 NOTE Harmonized as EN 61000-4-2.
IEC 62604-1:2015 NOTE Harmonized as EN 62604-1:2015 (not modified)
2

---------------------- Page: 4 ----------------------

SIST EN 62575-1:2016
EN 62575-1:2016
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.

NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu

Publication Year Title EN/HD Year

IEC 60027 Series Letter symbols to be used in electrical EN 60027 Series
technology
IEC 60050-561 -  International electrotechnical - -
vocabulary (IEV) -
Part 561: Piezoelectric, dielectric and
electrostatic devices and associated
materials for frequency control, selection
and detection
IEC 60068-1 2013 Environmental testing - EN 60068-1 2014
Part 1: General and guidance
IEC 60068-2-1 -  Environmental testing - EN 60068-2-1 -
Part 2-1: Tests - Test A: Cold
IEC 60068-2-2 -  Environmental testing - EN 60068-2-2 -
Part 2-2: Tests - Test B: Dry heat
IEC 60068-2-6 -  Environmental testing - EN 60068-2-6 -
Part 2-6: Tests - Test Fc: Vibration
(sinusoidal)
IEC 60068-2-7 -  Basic environmental testing procedures - EN 60068-2-7 -
Part 2-7: Tests - Test Ga and guidance:
Acceleration, steady state
IEC 60068-2-13 -  Basic environmental testing procedures - EN 60068-2-13 -
Part 2-13: Tests - Test M: Low air pressure
IEC 60068-2-14 -  Environmental testing - EN 60068-2-14 -
Part 2-14: Tests - Test N: Change of
temperature
IEC 60068-2-17 1994 Basic environmental testing procedures - EN 60068-2-17 1994
Part 2-17: Tests - Test Q: Sealing
IEC 60068-2-21 -  Environmental testing - EN 60068-2-21 -
Part 2-21: Tests - Test U: Robustness of
terminations and integral mounting devices
IEC 60068-2-27 -  Environmental testing - EN 60068-2-27 -
Part 2-27: Tests - Test Ea and guidance:
Shock
IEC 60068-2-30 -  Environmental testing - EN 60068-2-30 -
Part 2-30: Tests - Test Db: Damp heat,
cyclic (12 h + 12 h cycle)
3

---------------------- Page: 5 ----------------------

SIST EN 62575-1:2016
EN 62575-1:2016
Publication Year Title EN/HD Year

IEC 60068-2-31 -  Environmental testing - EN 60068-2-31 -
Part 2-31: Tests - Test Ec: Rough handling
shocks, primarily for equipment-type
specimens
IEC 60068-2-45 -  Basic environmental testing procedures - EN 60068-2-45 -
Part 2-45: Tests - Test XA and guidance:
Immersion in cleaning solvents
IEC 60068-2-52 -  Environmental testing - EN 60068-2-52 -
Part 2-52: Tests - Test Kb: Salt mist, cyclic
(sodium chloride solution)
IEC 60068-2-58 -  Environmental testing - EN 60068-2-58 -
Part 2-58: Tests - Test Td: Test methods
for solderability, resistance to dissolution of
metallization and to soldering heat of
surface mounting devices (SMD)
IEC 60068-2-64 -  Environmental testing - EN 60068-2-64 -
Part 2-64: Tests - Test Fh: Vibration,
broadband random and guidance
IEC 60068-2-78 -  Environmental testing - EN 60068-2-78 -
Part 2-78: Tests - Test Cab: Damp heat,
steady state
IEC 60122-1 -  Quartz crystal units of assessed quality - EN 60122-1 -
Part 1: Generic specification
IEC 60617-DB -  Graphical symbols for diagrams - -
IEC 60642 -  Piezoelectric ceramic resonators and - -
resonator units for frequency control and
selection - Chapter I: Standard values and
conditions - Chapter II: Measuring and test
conditions
IEC 60695-11-5 -  Fire hazard testing - EN 60695-11-5 -
Part 11-5: Test flames - Needle-flame test
method - Apparatus, confirmatory test
arrangement and guidance
1) 1)
IEC 60749-28 -  Semiconductor devices - Mechanical and EN 60749-28 -
climatic test methods -
Part 28: Electrostatic Discharge (ESD)
Sensitivity Testing Direct contact charged
device model (DC-CDM)
IEC 61340-3-1 -  Electrostatics - EN 61340-3-1 -
Part 3-1: Methods for simulation of
electrostatic effects - Human body model
(HBM) electrostatic discharge test
waveforms
IEC 61340-3-2 -  Electrostatics - EN 61340-3-2 -
Part 3-2: Methods for simulation of
electrostatic effects - Machine model (MM)
electrostatic discharge test waveforms
ISO 80000-1 -  Quantities and units - EN ISO 80000-1 -
Part 1: General


1)
At draft stage.
4

---------------------- Page: 6 ----------------------

SIST EN 62575-1:2016




IEC 62575-1

®


Edition 1.0 2015-10




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE
colour

inside










Radio frequency (RF) bulk acoustic wave (BAW) filters of assessed quality –

Part 1: Generic specification




Filtres radiofréquences (RF) à ondes acoustiques de volume (OAV) sous

assurance de la qualité –

Partie 1: Spécification générique














INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 31.140 ISBN 978-2-8322-2969-9



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 62575-1:2016
– 2 – IEC 62575-1:2015 © IEC 2015
CONTENTS
FOREWORD . 5
INTRODUCTION . 7
1 Scope . 8
2 Normative references. 8
3 Terms, definitions, units and symbols . 9
3.1 Terms and definitions . 9
3.2 Units and symbols . 15
4 Preferred values for ratings and characteristics . 15
4.1 General . 15
4.2 Nominal frequencies . 15
4.3 Operating temperature ranges, in degrees Celsius (°C) . 16
4.4 Climatic category . 16
4.5 Bump severity . 16
4.6 Vibration severity . 17
4.7 Shock severity . 17
4.8 Fine leak rate . 17
5 Marking . 18
5.1 Filter marking . 18
5.2 Package marking . 18
6 Quality assessment procedures . 18
6.1 General . 18
6.2 Primary stage of manufacture . 18
6.3 Structurally similar components . 18
6.4 Subcontracting . 18
6.5 Incorporated components . 18
6.6 Manufacturer’s approval . 19
6.7 Approval procedures . 19
6.7.1 General . 19
6.7.2 Capability approval . 19
6.7.3 Qualification approval . 19
6.8 Procedures for capability approval . 19
6.8.1 General . 19
6.8.2 Eligibility for capability approval . 20
6.8.3 Application for capability approval . 20
6.8.4 Granting of capability approval . 20
6.8.5 Capability manual . 20
6.9 Procedures for qualification approval . 20
6.9.1 General . 20
6.9.2 Eligibility for qualification approval. 20
6.9.3 Application for qualification approval . 20
6.9.4 Granting of qualification approval . 20
6.9.5 Quality conformance inspection . 20
6.10 Test procedures . 20
6.11 Screening requirements . 20
6.12 Rework and repair work . 21
6.12.1 Rework . 21

---------------------- Page: 8 ----------------------

SIST EN 62575-1:2016
IEC 62575-1:2015 © IEC 2015 – 3 –
6.12.2 Repair work . 21
6.13 Certified records of released lots . 21
6.14 Validity of release . 21
6.15 Release for delivery . 21
6.16 Unchecked parameters . 21
7 Test and measurement procedures . 21
7.1 General . 21
7.2 Test and measurement conditions . 21
7.2.1 Standard conditions of testing . 21
7.2.2 Precision of measurement . 22
7.2.3 Precautions. 22
7.2.4 Alternative test methods . 22
7.3 Visual inspection . 22
7.3.1 General . 22
7.3.2 Visual test A . 22
7.3.3 Visual test B . 23
7.3.4 Visual test C . 23
7.4 Dimensions and gauging procedures . 23
7.4.1 Dimensions test A . 23
7.4.2 Dimensions test B . 23
7.5 Electrical test procedures . 23
7.5.1 General . 23
7.5.2 Insertion attenuation measurement . 23
7.5.3 Return attenuation measurement . 25
7.5.4 Intermodulation distortion measurement . 27
7.5.5 Measurement of insertion attenuation characteristics at specified
terminating impedances and at standard atmospheric conditions . 28
7.5.6 Measurement of insertion attenuation characteristics as a function of
temperature . 28
7.5.7 Measurement of return attenuation at specified terminating impedance
and at the standard atmospheric conditions . 28
7.5.8 Measurement of intermodulation distortion at standard atmospheric
conditions . 28
7.5.9 Measurement method for the balanced type filter . 29
7.5.10 Insulation resistance . 30
7.5.11 Voltage proof . 30
7.6 Mechanical and environmental test procedures . 30
7.6.1 Robustness of terminations (destructive) . 30
7.6.2 Sealing tests (non-destructive) . 31
7.6.3 Soldering (solderability and resistance to soldering heat) (destructive) . 31
7.6.4 Rapid change of temperature: severe shock by liquid immersion (non-
destructive) . 31
7.6.5 Rapid change of temperature with prescribed time of transition (non-
destructive) . 32
7.6.6 Bump (destructive) . 32
7.6.7 Vibration (destructive) . 32
7.6.8 Shock (destructive) . 33
7.6.9 Free fall (destructive) . 33
7.6.10 Acceleration, steady state (non-destructive) . 33
7.6.11 Low air pressure (non-destructive) . 33

---------------------- Page: 9 ----------------------

SIST EN 62575-1:2016
– 4 – IEC 62575-1:2015 © IEC 2015
7.6.12 Dry heat (non-destructive) . 33
7.6.13 Damp heat, cyclic (destructive) . 33
7.6.14 Cold (non-destructive) . 34
7.6.15 Climatic sequence (destructive) . 34
7.6.16 Damp heat, steady state (destructive) . 34
7.6.17 Salt mist cyclic (destructive) . 34
7.6.18 Immersion in cleaning solvents (non-destructive) . 34
7.6.19 Flammability test (destructive) . 34
7.6.20 Electrostatic discharge (ESD) sensitivity test (destructive) . 34
7.7 Endurance test procedure . 35
Bibliography . 36

Figure 1 – FBAR configuration . 10
Figure 2 – SMR configuration . 11
Figure 3 – Frequency response of RF BAW filters . 15
Figure 4 – Insertion attenuation measurement . 24
Figure 5 – Return attenuation measurement . 25
Figure 6 – Intermodulation distortion measurement . 28
Figure 7 – Four-port network analyser measurement for balanced-balanced-
connection filter . 29
Figure 8 – Three-port network analyser measurement for unbalanced-balanced-
connection filter . 30

Table 1 – Frequency allocation of typical UMTS bands . 16

---------------------- Page: 10 ----------------------

SIST EN 62575-1:2016
IEC 62575-1:2015 © IEC 2015 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

RADIO FREQUENCY (RF) BULK ACOUSTIC WAVE (BAW)
FILTERS OF ASSESSED QUALITY –

Part 1: Generic specification

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62575-1 has been prepared by IEC technical committee 49:
Piezoelectric, dielectric and electrostatic devices and associated materials for frequency
control, selection and detection.
The text of this standard is based on the following documents:
FDIS Report on voting
49/1163/FDIS 49/1169/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 11 ----------------------

SIST EN 62575-1:2016
– 6 – IEC 62575-1:2015 © IEC 2015
A list of all parts in the IEC 62575, published under the general title Radio frequency (RF)
bulk acoustic wave (BAW) filters of assessed quality, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.

---------------------- Page: 12 ----------------------

SIST EN 62575-1:2016
IEC 62575-1:2015 © IEC 2015 – 7 –
INTRODUCTION
RF BAW filters are now widely used in mobile communications. While the RF BAW filters have
various specifications, many of them can be classified within a few fundamental categories.
Standard specifications, given in the IEC 62575 series, and national specifications or detail
specifications issued by manufacturers, define the available combinations of nominal
frequency pass bandwidth, ripple, shape factor, terminating impedance, etc. These
specifications are compiled to include a wide range of RF BAW filters with standardized
performances. It cannot be over-emphasized that the user should, wherever possible, select
his RF BAW filters from these specifications, when available, even if it may lead to making
small modifications to his circuit to enable standard filters to be used. This applies particularly
to the selection of the nominal frequency.
This standard has been compiled in response to a generally expressed desire on the part of
both users and manufacturers for guidance on the use of RF BAW
...