SIST EN ISO 1119:2004

SLOVENSKI STANDARD
SIST EN ISO 1119:2004
01-januar-2004
Geometrical product specifications (GPS) - Series of conical tapers and taper
angles (ISO 1119:1998)
Geometrical product specifications (GPS) - Series of conical tapers and taper angles
(ISO 1119:1998)
Geometrische Produktspezifikationen (GPS) - Reihen von Kegeln und Kegelwinkeln (ISO
1119:1998)
Spécification géométrique de produits (GPS) - Série d'angles de cônes et de conicités
(ISO 1119:1998)
Ta slovenski standard je istoveten z: EN ISO 1119:2002
ICS:
17.040.01 Linearne in kotne meritve na Linear and angular
splošno measurements in general
SIST EN ISO 1119:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 1119:2004

---------------------- Page: 2 ----------------------

SIST EN ISO 1119:2004
EUROPEAN STANDARD
EN ISO 1119
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2002
ICS 17.040.01
English version
Geometrical product specifications (GPS) - Series of conical
tapers and taper angles (ISO 1119:1998)
Spécification géométrique de produits (GPS) - Série Geometrische Produktspezifikationen (GPS) - Reihen von
d'angles de cônes et de conicités (ISO 1119:1998) Kegeln und Kegelwinkeln (ISO 1119:1998)
This European Standard was approved by CEN on 23 September 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1119:2002 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 1119:2004
EN ISO 1119:2002 (E)
Foreword
The text of ISO 1119:1998 has been prepared by Technical Committee ISO/TC 213
"Dimensional and geometrical product specifications and verification" of the International
Organization for Standardization (ISO) and has been taken over as EN ISO 1119:2002 by
Technical Committee CEN/TC 290 "Dimensional and geometrical product specification and
verification", the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by May 2003, and conflicting national
standards shall be withdrawn at the latest by May 2003.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,
Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the
United Kingdom.
Endorsement notice
The text of ISO 1119:1998 has been approved by CEN as EN ISO 1119:2002 without any
modifications.
2

---------------------- Page: 4 ----------------------

SIST EN ISO 1119:2004
INTERNATIONAL ISO
STANDARD 1119
Second edition
1998-09-15
Geometrical Product Specifications
(GPS) — Series of conical tapers and taper
angles
Spécification géométrique de produits (GPS) — Série d'angles de cônes et
de conicités
A
Reference number
ISO 1119:1998(E)

---------------------- Page: 5 ----------------------

SIST EN ISO 1119:2004
ISO 1119:1998(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national standards bodies (ISO member bodies). The work of
preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which
a technical committee has been established has the right to be represented
on that committee. International organizations, governmental and non-
governmental, in liaison with ISO, also take part in the work. ISO collab-
orates closely with the International Electrotechnical Commission (IEC) on
all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 1119 was prepared by the Technical Committee
ISO/TC 213, Dimensional and geometrical product specifications and
verification.
This second edition cancels and replaces the first edition (ISO 1119:1975),
of which the tables have been corrected and updated, but not technically
modified.
Annexes A and B of this International Standard are for information only.
©  ISO 1998
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet iso@iso.ch
Printed in Switzerland
ii

---------------------- Page: 6 ----------------------

SIST EN ISO 1119:2004
©
ISO ISO 1119:1998(E)
Introduction
This International Standard is a geometrical product specification (GPS)
standard and is to be regarded as a general GPS standard (see
ISO/TR 14638). It influences chain links 1 and 2 of the chain of standards
on angle.
For more detailed information of the relation of this International Standard
to other standards and the GPS matrix model, see annex A.
iii

---------------------- Page: 7 ----------------------

SIST EN ISO 1119:2004

---------------------- Page: 8 ----------------------

SIST EN ISO 1119:2004
©
INTERNATIONAL STANDARD  ISO ISO 1119:1998(E)
Geometrical Product Specifications (GPS) — Series
of conical tapers and taper angles
1  Scope
This International Standard gives a series of cones or conical tapers, ranging from 120° to less than 1°, or ratios
from 1:0,289 to 1:500, intended for general use in mechanical engineering.
It applies only to plain conical surfaces, and excludes prismatic pieces, taper threads, bevel gears, etc.
The method of dimensioning and tolerancing conical surfaces on drawings is covered in ISO 3040.
2  Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject to
revision, and parties to agreements based on this International Standard are encouraged to investigate the
possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain
registers of currently valid International Standards.
ISO 3:1973, Preferred numbers — Series of preferred numbers.
ISO 3040:1990, Technical drawings — Dimensioning and tolerancing — Cones.
3  Definitions
For the purposes of this International Standard, the following definitions apply.
3.1
cone angle
a
included angle between generatrixes as measured in the axial plane section
1

-----------------
...